GE GXPL03H Parts Included, Start Up Procedures, Not Wash Filter Cartridge

Page 2

Parts Included

 

Lid Cover

Easy-pour

 

Spout

Sliding Lid

 

 

Blue Filter Reminder

Reservoir

Light

 

Monitor Cover

40-gallon Filter

 

Cartridge

 

 

Pitcher

Start Up Procedures

1 Remove pitcher lid cover.

2 Unwrap filter cartridge and submerge the cartridge in clean water. Allow cartridge to soak for 15 minutes to flush out any loose, small carbon particles, which may be present in your water from the filter, but are not harmful.

3 Wash the pitcher, lid and reservoir with soap and warm water and rinse thoroughly. NOTE: NOT DISHWASHER SAFE. DO

NOT WASH FILTER CARTRIDGE.

4 Place the reservoir into the pitcher. Make sure the spout and handle recess on the reservoir are in the correct orientation.

Spout

Handle

Recess

Recess

 

5 Push filter cartridge firmly into reservoir to create a good seal.

Filter

Reservoir

Start Up Procedures (cont.)

6 Install battery.

• Remove battery and monitor assembly from plastic bag inside the pitcher. Turn the monitor cover over and remove battery cover by removing the screw and prying the cover off.

Battery

Cover

•Insert one CR2032, 3 volt battery positive “+” side up under the retaining clip.

NOTE: Make sure the positive (+) side of the battery is up.

Retaining Clip

Battery Positive

(+) Side Up

•Replace the battery cover by pressing around the lip to make sure it is fully installed.

•The blue light will flash five times, indicating that the timer is working. NOTE: If the blue light does not flash, check battery orientation.

•Press the monitor cover into place on the handle. It will snap when it is in the proper position.

Monitor

Cover

7 Replace lid cover. The lid will snap when it is in the proper location. Open the sliding lid and fill the reservoir with cold tap water and set the pitcher aside. Filtered water will begin to collect in the bottom of the pitcher. Continue to add water until the filtered water in the pitcher reaches the bottom of the reservoir. Do not overfill. Keep water below the bottom edge of the slot (see illustration below). Close the sliding lid on the pitcher.

Sliding

Lid

Fill to the bottom edge of the sliding lid track.

NOTE: If small, black carbon particles are present in the filtered drinking water, the filter cartridge may not have been thoroughly flushed. These small carbon particles are harmless, though it may be necessary to empty the first 1–2 pitchers of filtered water to flush out any remaining carbon particles.

8 Keep pitcher filter refrigerated at all times. After 3 to 4 days, replace unused water with fresh, clean water.

2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Filtration Pitcher GE Model GXPL03H USE and CARE/INSTALLATION InstructionsGE Water Filtration Pitcher Not Wash Filter Cartridge Start Up ProceduresParts Included Replacement Cartridge Filter Indicator LightCartridge Replacement Procedure Filling the Pitcher with Tap WaterPage Pot à filtre Modèle GE GXPL03H Utilisation ET ENTRETIEN/INSTRUCTIONS D’INSTALLATIONPot à eau avec filtre GE Cartouches FXPL3D & FXPL3CADInstructions de démarrage suite Pièces fourniesInstructions de démarrage NE Lavez PAS LA Cartouche DE FiltrationTémoin lumineux Remplacement de la cartoucheCartouche de filtration de remplacement Remplissage du pot avec de l’eau du robinetPage Jarra de filtración GE Modelo GXPL03H Jarra de filtración de agua GEUSO Y Cuidado / Instrucciones DE Instalación Cartuchos FXPL3D & FXPL3CADNo Lave EL Cartucho DEL Filtro Piezas incluidasProcedimientos de inicio Recambio del filtro en el cartucho Luz indicadoraProcedimiento para la sustitución del cartucho Llenado de la jarra con agua corriente

GXPL03H specifications

The GE GXPL03H is an advanced, high-efficiency heat pump water heater that combines innovative technology with user-friendly features. As part of GE's commitment to energy efficiency and sustainability, the GXPL03H is designed to meet the needs of homeowners looking to reduce their energy bills while benefiting the environment.

One of the standout features of the GXPL03H is its impressive energy efficiency rating. The unit has a high Energy Factor (EF) rating, meaning that it uses significantly less energy compared to traditional water heaters. This is primarily achieved through its advanced heat pump technology, which extracts heat from the surrounding air and uses it to heat the water, rather than generating heat directly. As a result, the GXPL03H can deliver substantial energy savings, making it an appealing choice for eco-conscious consumers.

The GXPL03H comes with a user-friendly digital interface that allows homeowners to easily set and monitor their hot water needs. The intuitive control panel provides access to various operating modes, including efficiency modes and high-demand settings, empowering users to optimize the system's performance based on their specific requirements. With options for vacation mode and other programmable settings, the GE GXPL03H can be customized for maximum efficiency and convenience.

Another notable characteristic of the GXPL03H is its robust construction. The unit features a durable exterior and a high-quality tank designed to maintain the temperature of the water efficiently. This design contributes to the longevity of the water heater and minimizes maintenance needs over time.

Additionally, the GE GXPL03H is equipped with advanced noise-reduction technology, ensuring that it operates quietly, making it suitable for indoor installation without causing disruptions. The unit also includes a comprehensive warranty, providing added peace of mind for users.

In summary, the GE GXPL03H heat pump water heater is an efficient, technologically advanced solution for homeowners seeking to lower their energy costs and decrease their environmental impact. With its innovative design, intuitive features, and reliable performance, it represents a significant step toward the future of eco-friendly home appliances.
Top Page Image Contents