GE GX1S50F Replacing the Filter Canister, Flush Procedure, Cómo reemplazar el cartucho del filtro

Page 12

Installation Instructions.

Replacing the Filter Canister

The blue light in the faucet base will flash every 30 seconds to indicate a filter change is needed. This occurs every 6 months.

1.Remove the filter canister from the manifold by rotating the canister to the left about 1/3 turn (Fig. 9). NOTE: A small amount of water from the tubing between the filter and the faucet may come out. A small towel should be able to catch it.

2.Remove foil on top of new replacement filter canister. Install the new canister into the manifold by turning it to the right about 1/3 turn until the alignment marks line up and the filter stops. DO NOT OVERTIGHTEN. The filter will rise up as it is turned.

3.Turn handle on faucet to allow trapped air to purge from the system.

NOTE: System may make noise during this procedure.

4.Check for water leaks around the system.

5.Once water starts to flow out of the faucet, allow the system to run for 5 minutes to flush out any harmless carbon fines that may be present.

6.Turn off faucet and check around system for leaks.

7.Remove battery tray and replace battery to reset timer. (See Battery Installation for proper procedure).

Fig. 9

To install

To remove

Replacement Filter Canister/Estimated Replacement Costs

GXRLQR—Replacement filter canister $30–35

For replacement parts, call toll-free 800.626.2002.

Flush Procedure

Whenever water of unknown quality is passed through the GE Water Filtration system, the filter canister should be discarded and the filtration system flushed.

WARNING: These systems should only be used on microbiologically safe water.

Circumstances that may require flushing the system are:

•Boil water advisory

•Flooding of the GE Water Filtration system

•Long-term non-use

The procedure for flushing the GE Water Filtration system is:

1.See Replacing the Filter Canister section and follow steps 1–4.

Instrucciones de instalación.

Cómo reemplazar el cartucho del filtro

La luz azul en la base del grifo se encenderá de forma intermitente cada 30 segundos para indicar que es necesario cambiar el filtro. Esto ocurre cada 6 meses.

1.Retire el cartucho del filtro del recolector girando el cartucho hacia la izquierda 1/3 de giro. (Fig. 9). NOTA: Podría salir una pequeña cantidad de agua de la tubería entre el filtro y el grifo, la cual se puede absorber con una toalla pequeña.

2.Retire el aluminio de la parte superior del cartucho de repuesto. Instale el nuevo cartucho en el recolector girándolo hacia la derecha alrededor de 1/3 de giro hasta que las marcas de alineación queden en línea y el filtro pare. NO APRIETE EN EXCESO. El filtro podría levantarse a medida que se gira.

3.Gire la manija en el grifo para permitir que el aire atrapado se purgue del sistema.

NOTA: Es posible que el sistema haga ruido durante este procedimiento.

4.Busque fugas de agua alrededor del sistema.

5.Una vez que el agua empiece a fluir del grifo, deje que el sistema opere por 5 minutos para expulsar cualquier traza de carbono que pueda estar presente.

6.Cierre el grifo y revise alrededor del sistema en busca de fugas.

7.Retire la bandeja de la batería y vuelva a instalar la batería para inicializar el temporizador. (Vea la instalación de la batería para el procedimiento correcto).

Fig. 9

Para

Para

instalar

retirar

Repuesto del cartucho del filtro/Costos estimados de reposición

GXRLQR—Repuesto del cartucho del filtro $30–35

Para repuestos, llame gratis al 800.626.2002 (EE.UU.).

Procedimiento para lavar

Cada vez que agua de calidad desconocida es pasada a través del sistema de filtración de agua GE, el cartucho del filtro debería ser deshechado y el sistema de filtración lavado.

ADVERTENCIA: Estos sistemas solamente deberían usarse en agua microbiológicamente segura.

Las circunstancias que podrían requerir el lavado del sistema son:

•Advertencia de que hay que hervir el agua

•Inundación del sistema de filtración de agua GE

•Largo tiempo sin ser usado

El procedimiento para lavar el sistema de filtración de agua GE es:

1.Vea la sección Cómo reemplazar el cartucho del filtro y siga los pasos 1–4.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Water Filtration System Sistema de Filtración de Agua Manual del propietarioLEA Todas LAS Instrucciones Antes DE Usar Installation Overview Water Filtration System Uses the Following CanisterGeneralidades sobre la instalación Model GX1S50FSmartWater Filtration System GX1S50F Using Filter Gxrlqr Replacement Filter Canister/Estimated Replacement CostsImportant Installation Recommendations Tools and Materials Required for InstallationContents Included with the Product Recomendaciones importantes para la instalaciónCold Water Supply Fitting Accesorio para el suministro de agua fríaFaucet Spout Installations see , Instalación del pico del grifo ver , páginaOption OpciónFaucet Installation Installation Steps refer to for clarificationInstalación del grifo Pasos para la instalación consulte la para aclaraciónMounting System Installation Mounting Using the Screw Provided FigMontaje del sistema Montaje utilizando el tornillo suministrado FigInstalling the Tubing Cómo instalar la tuberíaBattery Installation Instalación de la bateríaFlush Procedure Replacing the Filter CanisterCómo reemplazar el cartucho del filtro Procedimiento para lavarBefore you call for service… Antes de solicitar un servicio… La luz indicadora en la base del grifo está intermitenteOlor y/o sabor a cloro en el agua producida Instalado completamenteSoporte al consumidor Página Web de GE Solicite una reparaciónGarantías ampliadas Piezas y accesoriosSchedule Service Parts and AccessoriesGE Water Filtration System Warranty Consumer Support GE Appliances Website

GX1S50F specifications

The GE GX1S50F is an advanced water filtration system designed to provide clean and safe drinking water for households. This innovative system utilizes cutting-edge technologies to ensure that contaminants are effectively reduced while enhancing the overall taste and quality of the water.

One of the main features of the GE GX1S50F is its three-stage filtration process. The system first employs a sediment filter that captures large particles such as dirt, sand, and rust, ensuring that these impurities do not reach the subsequent stages. Following this, a carbon block filter takes over, which is adept at removing chlorine, lead, and other harmful chemicals that can affect the water's taste and safety. Finally, the system features a post-carbon filter that polishes the water, providing the finishing touch to ensure that every drop is crystal clear and fresh.

The GE GX1S50F is designed with user convenience in mind. Its compact size makes it easy to install, fitting seamlessly under most sinks without taking up excessive space. The system is also equipped with a simple shut-off valve, which allows users to quickly halt water flow during filter changes, minimizing mess and ensuring a straightforward replacement process.

Another significant characteristic of the GE GX1S50F is its durability and longevity. The filters are engineered to last up to six months, depending on usage and water quality, allowing households to enjoy cleaner water for a prolonged period without frequent replacements. This not only saves time but also adds to the system's cost-effectiveness.

In addition to its performance features, the GE GX1S50F is designed with sustainability in mind. By providing an efficient means of filtering tap water, the system reduces the reliance on single-use plastic water bottles, promoting an eco-friendly approach to water consumption.

Overall, the GE GX1S50F is a state-of-the-art water filtration solution that combines advanced technology with practical design. With its three-stage filtration process, easy installation, long-lasting filters, and commitment to sustainability, it offers an excellent choice for families looking to improve their drinking water quality while being mindful of their environmental impact.
Top Page Image Contents