Cold Water Supply Fitting

Installation Instructions.

A.PREFERRED INSTALLATION

(Utilizing existing kitchen sink water supply valve and flexible faucet tubing)

A typical connection using the included water supply fitting is shown in the illustration below.

1.Close the water shut-off valve that is immediately in front of the supply tube and open the faucets to drain water from the sink cold water pipe.

2.Remove the nut that connects the cold water faucet to the supply tube. Some water may spill out.

NOTES:

•Be sure to turn off the water supply and open a faucet to drain the pipe.

•Make sure the gasket is installed in the water supply fitting.

Instrucciones de instalación.

Accesorio para el suministro de agua fría

A.INSTALACIÓN PREFERIDA

(Utilizando la válvula existente de suministro de agua del lavaplatos de la cocina y la tubería flexible del grifo)

En la ilustración que aparece a continuación se muestra una conexión típica usando el accesorio para el suministro de agua incluido.

1.Cierre la válvula de agua que se encuentra inmediatamente en frente del tubo de suministro y abra los grifos para dejar correr el agua de la tubería de agua fría del lavaplatos.

2.Retire la tuerca que conecta el grifo de agua fría al tubo de suministro. Es posible que se derrame un poco de agua.

NOTAS:

•Asegúrese de cerrar el suministro de agua y abra el grifo para drenar la tubería.

•Asegúrese que esté instalada la junta en el accesorio de suministro de agua.

Cold Water	Gasket
Faucet Stud

Water Supply Fitting

1/4″ Tubing to Water Filter Inlet

Fig. 1

Cold

Water Pipe

Cold Water Shutoff

Perno del grifo de agua fría

Tubería de agua fría

Junta

Accesorio de suministro de agua

Tubo de 1/4” a entrada

del filtro de agua

Fig. 1

3.Hand-tighten the water supply fitting onto the cold water faucet. Be sure the gasket, as shown, is in place before final assembly. Finish tightening with an adjustable wrench. Be careful not to

overtighten or cross-thread, as damage to the threads can occur. Make sure the 1/4″ quick connection is not against a wall that causes the supply tubing connection to bend. A quarter turn to tighten or loosen the adapter may be necessary to avoid this.

4.Reconnect faucet tubing line to the fitting.

5.Install tubing. (See Installing the Tubing section.)

Válvula de cierre de agua fría

3.Ajuste en forma manual el accesorio de suministro de agua fría en el grifo de agua fría. Asegúrese que la junta, como se muestra, esté en su lugar antes del ensamble final. Termine de colocar la misma con una llave de ajuste. Asegúrese de no forzar ni presionar por

demás a fin de evitar dañar la rosca. Asegúrese que la conexión rápida de 1/4″ no esté contra una pared que haga que la conexión del tubo de suministro se tuerza. Es posible que se necesite presionar o aflojar el adaptador con un cuarto de giro a fin de evitar esto.

4.Vuelva a conectar la tubería del grifo al accesorio.

5.Instale la tubería. (Consulte la sección de Instalación de la tubería.)

GX1S50F specifications

The GE GX1S50F is an advanced water filtration system designed to provide clean and safe drinking water for households. This innovative system utilizes cutting-edge technologies to ensure that contaminants are effectively reduced while enhancing the overall taste and quality of the water.

One of the main features of the GE GX1S50F is its three-stage filtration process. The system first employs a sediment filter that captures large particles such as dirt, sand, and rust, ensuring that these impurities do not reach the subsequent stages. Following this, a carbon block filter takes over, which is adept at removing chlorine, lead, and other harmful chemicals that can affect the water's taste and safety. Finally, the system features a post-carbon filter that polishes the water, providing the finishing touch to ensure that every drop is crystal clear and fresh.

The GE GX1S50F is designed with user convenience in mind. Its compact size makes it easy to install, fitting seamlessly under most sinks without taking up excessive space. The system is also equipped with a simple shut-off valve, which allows users to quickly halt water flow during filter changes, minimizing mess and ensuring a straightforward replacement process.

Another significant characteristic of the GE GX1S50F is its durability and longevity. The filters are engineered to last up to six months, depending on usage and water quality, allowing households to enjoy cleaner water for a prolonged period without frequent replacements. This not only saves time but also adds to the system's cost-effectiveness.

In addition to its performance features, the GE GX1S50F is designed with sustainability in mind. By providing an efficient means of filtering tap water, the system reduces the reliance on single-use plastic water bottles, promoting an eco-friendly approach to water consumption.

Overall, the GE GX1S50F is a state-of-the-art water filtration solution that combines advanced technology with practical design. With its three-stage filtration process, easy installation, long-lasting filters, and commitment to sustainability, it offers an excellent choice for families looking to improve their drinking water quality while being mindful of their environmental impact.