GE PNRQ16RBL, PXRQ15RBL owner manual Installation Instructions Faucet Assembly, Install the Battery

Page 15

Installation Instructions

FAUCET ASSEMBLY (cont.)

OPTIONAL ONE-PERSON FAUCET TUBING INSTALLATION

1.From under the sink, gather the 1/4” drain line (black), 3/8” drain line (black) and 3/8” outlet tube (blue banded) in one hand with the drain tubes the same length and the outlet tube offset approximately 6 inches.

2.Wrap a rubber band around all 3 tubes.

3.Insert a typical No. 2 pencil through the rubber band location.

4.Rotate the pencil down until it is in line with the tubing and push up through the mounting hole. Release the grip on the pencil and the tubes will remain in position for easier faucet connection.

INSTALL THE BATTERY

1.Remove the lens cover from the faucet base. Grip it from both sides and pull forward.

2.Install one CR2032 3V battery with the “+” side DOWN into the battery tray. Slide the battery tray completely back into the base.

Faucet base

Lens cover

Battery “+”side down

 

 

 

3.Each light will illuminate in sequence twice. The OK (green) light or Filter (amber) light may stay on for a few extra seconds. If you want to reinitiate the start-up sequence, remove the battery for 90 seconds so the electronics can fully reset; then put the battery back in.

4.The OK (green) light will normally flash one time per second when dispensing water. If the system needs service, the Filter or R.O. (amber) lights will flash one time per second while dispensing and will randomly flash when not in use.

NOTE: For lights to change between OK and R.O., the system must detect a change in the filtering process for

25 consecutive seconds. For example, if the system was showing that service was needed, it will take 25 seconds of consecutive filtering for the system to confirm the correct service changes were made.

FOR FILTER CHANGE: Replace the battery when changing the filter. Remove the used battery and wait 90 seconds before installing the new battery to ensure the proper electronics are reset for the next 6 months.

15

Image 15
Contents Reverse Osmosis SafetyINfORMatION PROPeRINstaLLatIONaNDMaINteNaNce Operating Specification guidelinesHow the Reverse Osmosis System Works About the reverse osmosis systemOperating Instructions Safety Instructions Tools and Materials Required for Installation Before Beginning InstallationContents Included With Product Filtration Drain Connection Basement InstallationTUBING/FILTER Detail Feed WaterMounting System Installation Reverse Osmosis AssemblyPreferred Installation Optional InstallationFeed Water Supply Optional Installation 1 Installation Instructions Feed Water SupplyOption Optional Rigid Pipe InstallationFlow Restrictor Replacement Procedure Installing the Tubing to Tank and FaucetInstall the Faucet Faucet AssemblyInstall the Battery Installation Instructions Faucet AssemblyPreferred Installation Option A-BASEMENT Access Filtration Drain ConnectionCheck and comply with local plumbing codes as you plan By the user Installation Instructions Filtration Drain ConnectionStorage Tank Installation System Startup ProcedureStorage Tank and Startup Safety Care and cleaning of the reverse osmosis systemSanitizing the Reverse Osmosis System Water Test Kit Troubleshootingtips Before you call for service…Troubleshooting Tips Consumer Support Parts list REF. no GE Part no Part DESCRIPTION1 Parts catalogGE Reverse Osmosis System Warranty Mesures de sécurité La section FrançaiseConsignes DE Sécurité Conservez CES Instructions ConsommateurSoutien au Conseils de dépannage Guide des spécificationsCe que ce système accomplit Au sujet du système de filtration par osmose inverséeAu sujet du système de filtration par osmose inversée Veuillez lire toutes les directives attentivement Outillage ET Matériel Requis Pour L’INSTALLATIONAvant DE Commencer ’INSTALLATION Liste DES Composants DE L’APPAREILRaccord DU Système DE Filtrage À LA Vidange Installation Dans UN SOUS-SOLDétail DES TUYAUX/DU Filtre EAU D’ALIMENTATIONEnsemble D’OSMOSE Inversée Installation DU Système DE MontageRebranchez le tuyau dalimentation au raccord Installation PréféréeInstallation OPTIONNELLE-1 Alimentation D’EAUInstallation OPTIONNELLE-2 Instructions d’installation Alimentation D’EAU suiteSuite Installation À DistanceProcédure DE Remplacement DU Réducteur DE Débit Installation DU Tuyau AU Réservoir ET AU RobinetInstallation DU Robinet Installation DU Robinet SuiteDispositif DU Robinet Installation DE LA Pile Instructions d’installation Installation DU Robinet suiteDU Système AU SOUS-SOL Raccordements À LA Conduite DE Vidange’INSTALLEZ PAS LE Tuyau DE Vidange EN Vérifiez qu’il n’y ait pas de fuite aux points de Procédure DE Mise EN Marche DU SystèmeMis Ouvrez le robinet d’approvisionnement d’eauSécurité Fonctionnement Fonctionnement Mesures Trousse de test d’eau Avant d’appeler un réparateur Conseils de dépannage Liste de pièces Capuchon D’INDICATEUR DE Débit ET Joint Torique Catalogue des piècesPour la période de GE remplacera Garantie du système de filtration par osmose inversée de GEProlongation de garantie Soutien au consommateur Service de réparationsInstrucciones de instalación La sección en EspañolInformación DE Seguridad Conserve Estas Instrucciones Producto altura 11 ancho 10,5 profundidad Pautas sobre las especificaciones¿Qué hace el sistema de Ósmosis Inversa? Sobre el sistema de Ósmosis InversaInstalación Soporte al consumidor Solucionar problemas Antes DE Empezar LA Instalación Contenidos Incluidos CON EL ProductoLea estas instrucciones completa y cuidadosamente Grifo DEL Sistema DE OI Detalle DE LOS TUBOS/FILTROAgua DE Alimentación Conexión DEL Drenaje DE FiltraciónEnsambladura DEL Sistema DE Ósmosis Inversa Instalación DEL Sistema DE MontajeImportante No permita que Suministro DE Agua DE Alimentación Instalación PreferidaInstalación Opcional Para tubería metal de 1/2 DE o más largo únicamente Las roscas ya que se podrían dañarInstalación Opcional DE Tubería Rígida Instalación EN UNA Ubicación RemotaOpción Procedimiento DE Reemplazo DEL Estrangulador DE Flujo Cómo Instalar LA Tubería AL Tanque Y AL GrifoInstalación DEL Grifo Ensambladura DEL GrifoInstalación DE LA Batería Instalación DEL Cable EléctricoConexión DEL Drenaje DE Filtración Precaución El uso Tanque DE Almacenamiento Y Arranque Instalación DEL Tanque DE AlmacenamientoProcedimiento Para EL Arranque DEL Sistema Solucionar Cuidado y limpieza del sistema de Ósmosis InversaImportante Antes de la Kit de prueba del agua Consejos para la solución de fallas Antes de llamar a solicitar servicio…Solucionar problemas Lista de partes NO. REF Parte no Descripción DE LA Parte Catálogo de partesNotas Notas Garantía del Sistema Ósmosis Inversa Piezas y accesorios Soporte al consumidor Página Web de GE AppliancesSolicite una reparación Garantías ampliadasConsumer Support Schedule Service

PNRQ16RBL, PXRQ15RBL specifications

The GE PXRQ15RBL and PNRQ16RBL are standout refrigerator models that combine modern design with advanced technologies, making them a top choice for consumers seeking both functionality and style in their kitchen. These models are part of GE's renowned Profile series, which is known for its innovative features and energy efficiency.

One of the main features of both the PXRQ15RBL and PNRQ16RBL is their spacious interior, designed to maximize storage space while providing easy access to food items. The shelves are adjustable, allowing users to customize the layout according to their needs. With ample storage options, including bins, drawers, and door storage, these refrigerators make organization seamless and efficient.

Energy efficiency is a major characteristic of these models, complying with ENERGY STAR standards. This not only helps reduce the carbon footprint but also translates into savings on utility bills over time. The advanced cooling technology ensures that food stays fresher for longer periods, maintaining optimal temperatures and humidity levels throughout the interior.

Additionally, the PXRQ15RBL and PNRQ16RBL feature GE's advanced ice and water dispenser located conveniently on the door. This feature provides quick access to chilled water and ice without the hassle of opening the refrigerator, enhancing convenience for everyday use. The dispensers are designed to reduce spills, ensuring a clean and tidy kitchen experience.

Another significant technology incorporated in these models is the "TwinChill" evaporators, which separate the climates in the fresh food and freezer sections. This innovative design prevents the transfer of odors between compartments and helps maintain ideal humidity levels, further preserving the freshness of food items.

Both refrigerators are also equipped with LED lighting, providing clear visibility throughout the interior while being energy-efficient. The sleek black finish enhances the modern aesthetic, allowing these refrigerators to seamlessly blend with any kitchen decor.

In conclusion, the GE PXRQ15RBL and PNRQ16RBL refrigerators are exemplary models that cater to the needs of today’s consumers. With features such as spacious interiors, energy efficiency, advanced cooling technology, and convenient ice and water dispensers, these refrigerators represent a perfect balance of style, innovation, and practicality in the modern kitchen. Their thoughtful design and superior functionality make them a worthy investment for those looking to upgrade their kitchen appliances.