GE PNRQ16RBL, PXRQ15RBL owner manual PROPeRINstaLLatIONaNDMaINteNaNce

IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.	GEAppliances.com

PROPeRINstaLLatIONaNDMaINteNaNce

thisReverseOsmosissystemmustbeproperlyinstalledandlocatedinaccordancewiththe InstallationInstructionsbeforeitisused.

Safety Instructions

nExtended non-use of the Reverse Osmosis system. If the system has not been used for one week or more, open the RO water faucet and allow the system to drain. Close the RO water faucet and allow the system to regenerate the water supply.

nRecommended installation is under the sink. However, the unit can be installed in a remote location, up to 20 feet away from the sink.

•However, additional materials will be required. See parts list to obtain additional materials from GE.

•Locating the tank on a basement floor, with the faucet at a first floor sink may result in some loss of flow rate and capacity (approximately 20%). Installing a second tank will improve this performance. An RVKIT can be used.

nIf Reverse Osmosis system is connected to a refrigerator icemaker, a special icemaker connection kit is required (RVKIT). Do not use copper tubing for the connection between the Reverse Osmosis system and the refrigerator.

nSanitize upon installation of the Reverse Osmosis system and after servicing inner parts, including replacement of prefilter, postfilter and Reverse Osmosis cartridge. It is important to have clean hands while handling inner parts of the system. See the sanitizingtheReverseOsmosissystem section.

nThis Reverse Osmosis system contains a replaceable treatment component critical for effective reduction of total dissolved solids. This product water shall be tested periodically to verify that the system is performing satisfactorily. See the theWatertestKit section.

BE SURE TO FOLLOW ALL APPLICABLE STATE AND LOCAL CODES.

CAUTION: To reduce the risk associated with property damage due to water leakage:

•Read and follow these instruction before installation and use of this system.

•Installation and use MUST comply with all state and local plumbing codes.

•Protect from freezing, remove filter cartridge when temperatures are expected to drop below 40° F (4.4° C).

•Do not install systems in areas where ambient temperatures may go above 110° F (43.3° C).

•Do not install if water pressure exceeds 120 psi (827 kPa). If your water pressure exceeds 80 psi (552 kPa), you must install a pressure limiting valve. Contact a plumbing professional if you are uncertain how to check your water pressure.

•Do not install where water hammer conditions may occur. If water hammer conditions exist, you must install a water hammer arrester. Contact a plumbing professional if you are uncertain how to check for this condition.

•Where a back flow prevention device is installed on a water system, a device for controlling pressure due to thermal expansion must be installed.

CAUTION: To reduce the risk associated with property damage due to water leakage:

•Do not use a torch or other high temperature sources near filter system, cartridges, plastic fittings or plastic plumbing.

•On plastic fittings, never use pipe sealant or pipe dope. Use PTFE thread tape only, pipe dope properties may deteriorate plastic.

•Take care when using pliers or pipe wrenches to tighten plastic fittings, as damage may occur if over tightening occurs.

•Do not install in direct sunlight or outdoors.

•Do not install near water pipes which will be in path of a drilling tool when selecting the position to mount the bracket.

•Mount filter in such a position as to prevent it from being struck by other items used in the area of installation.

•Ensure that the location and fasteners will support the weight of the system when installed and full of water.

•Ensure all tubing and fittings are secure and free of leaks.

•Do not install unit if any collets (parts 27 and 28 on page 24) are missing . Contact 800.626.2002 (U.S.), 800.663.6060 (Canada-English),

800.362-3869 (Canada-French) if collets are missing from any fittings to obtain replacements.

•Replace the disposable pre and post filter cartridges every 6 months, at the rated capacity or sooner if a noticeable reduction in flow rate occurs.

•Replace the disposable RO cartridge every 24 months or sooner if a noticeable reduction in filtration efficiency occurs.

Operating Instructions

Installation Instructions

Troubleshooting Tips Consumer

READ AND FOLLOW ThIS SAFETY INFO RMATION CAREFULLY. SAVE ThESE INSTRUCTIONS

3

Support