Harman-Kardon 660 Step Twelve Plug in AC Power Cords, Step Thirteen Insert Batteries in Remote

Page 23

STEP TWELVE – Plug in AC Power Cords

Before plugging the AVR into an unswitched electrical outlet, make sure the Main Power Switch behind the front-panel door is off, to prevent the possibility of damaging the AVR in case of a transient power surge. When pressed in, the switch is on. When pressed again to unlatch it, the switch pops out.

You may plug one device that draws no more than 50 watts into the AC Switched Accessory Outlet on the rear panel. Turn on the device’s mechanical or master power switch, and that device will power on any time the AVR 760/ AVR 660 is turned on (some devices may require additional steps to power on from their standby mode). If the device has a clock or must always be on (such as a cable set-top box programmed to make recordings), do not plug it into this outlet.

The AVR 760/AVR 660 is equipped with a detachable power cord, allowing you to fully wire your system before installing the AVR. Plug the male end of the cord into an unswitched AC outlet, and the female end into the AVR 760/ AVR 660.

The Advanced Manual available for download from the harman/kardon web site contains a Table A5 designed for you to enter the information from Table 2 for future reference.

STEP THIRTEEN – Insert Batteries in Remote

The AVR 760/AVR 660 remote control uses four AAA batteries (included).

To remove the battery cover located on the back of the remote, squeeze the tab and lift the cover.

Insert the batteries as shown in Figure 18, observing the correct polarity.

Figure 18 –  Remote Battery Compartment

Point the remote’s lens toward the front panel of the AVR 760/AVR 660. Make sure no objects, such as furniture, are blocking the remote’s path to the receiver. Bright lights, fluorescent lights and plasma video displays may interfere with the remote’s functioning. The remote has a range of about 7 meter, depending on the lighting conditions. It may be used at an angle of up to 30 degrees to either side of the AVR.

Leave the Zone Selector Switch at the bottom in the Zone 1 position for normal use.

If the remote seems to operate intermittently, or if pressing a button on the remote does not cause the AVR Settings Button or one of the Source Selectors to light, check or replace the batteries.

INSTALLATION

STEP FOURTEEN – Program Sources Into the Remote

The AVR 760/AVR 660 remote may be programmed to control many brands and models of DVD players, cable boxes, satellite receivers, the Harman Kardon DMC 1000 digital media center and TVs. It is also preprogrammed to operate your iPod when docked in The Bridge II.

To access the functions for a particular device, switch the remote’s device mode. Press the AVR Settings Button to access the codes that control the receiver, or the Source Selector Buttons to access the codes for the devices programmed into the remote.

To program the codes for a source device into the remote:

1.Turn on the source device.

2.Access the remote’s menu system by pressing and holding the AVR Settings Button for 3 seconds, until the “Main Menu” and “Program Device” messages appear in the LCD Display.

3.Press the OK Button to select the Program Device function.

4.Use the KL Buttons to select the Source Selector (or device) to program, and press the OK Button when the desired device appears on the lower line of the LCD Display.

5.For two of the Source Selectors and for sources A, B, C and D, the next step requires you to specify the device type. For the other Source Selectors, proceed to step 6.

•• Cable/SAT: Use the KL Buttons to select either a cable television or satellite television set-top box, and press the OK Button.

•• AUX: Use the KL Buttons to select a CD player, HDTV set-top box, PVD (personal video device, such as a DVR), TiVo system or VCR. Press the OK Button when the desired device appears.

•• A, B, C, D: Select any desired device type.

6.Select whether to program the device manually or use the remote’s Auto Search capability. Manual programming simply requires you to select the brand name of your device and try a handful of possible codes. There is no need to look up numeric codes; the AVR 760/AVR 660 does the work for you. It is recommended that you select Manual programming first.

•Manual Programming: Use the KL Buttons to scroll through the list of brands for which the remote has codes stored in its library. When your brand appears on the lower line, press the OK Button.

The remote will look up the brand in its library and display the number of codes available. Press the “1” Alphanumeric Key first. The remote will transmit the Power Off command associated with the first code set to the device. If the device turns off, then a compatible code set has been found. Press the OK Button to accept it.

If the device remains powered on, press the “2” Alphanumeric Key. Proceed in this fashion until either a compatible code set is found, or you run out of codes for that brand.

If you run out of codes, press the Back/Exit Button to end the process, and repeat steps 2 through 5. At step 6, select Auto and follow the instructions in the next bullet.

ENGLISH

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents AVR 760/AVR Important Safety Information Safety InformationImportant Safety Instructions Moving the Unit Installation LocationCleaning Do Not Open the CabinetTable of Contents Surround Modes IntroductionThank you for choosing a Harman Kardon product Audio SectionDigital Audio Inputs Supplied AccessoriesAudio Inputs Audio/Video InputsFRONT-PANEL Controls Setting 480i, 480p, 576i, 720p, 1080i or 1080pVolume Knob Turn this knob to raise or lower the volume Output REAR-PANEL ConnectionsUse an HDMI-to-DVI adapter Main Remote Control Remote Control FunctionsVolume Control Press to raise or lower the volume Zone 2 Remote Control Surround Modes Introduction to Home TheaterTypical Home Theater System Multichannel AudioSubwoofer Connecting Source Devices to the AVRConnections Speaker ConnectionsAnalog Audio Digital AudioDigital Video AntennasRS-232 Serial Port Video ConnectionsSubwoofer Placement Speaker PlacementFront Speaker Placement Source Assignment Worksheet Getting StartedGetting Started Installation Select one or all of these methods for audio distribution Step Eleven Install a Multizone SystemConnect a Video Display Device or Switcher AVR 760 only Connect IR Control Devices to the Zone 2 IR InputTo program the codes for a source device into the remote Step Twelve Plug in AC Power CordsStep Thirteen Insert Batteries in Remote Step Fourteen Program Sources Into the RemoteTo learn individual key codes To change the device type of a Source SelectorStep Fifteen Turn On the AVR 760/AVR 660 To delete a programmed or learned codeTo rename a key or device Select Automatic Setup-EzSet/EQ Initial SetupUsing the On-Screen Menu System Audio and Video Input Selection Set Up SourcesSelect Cancel to return to the Speaker Setup menu HDMI-Equipped Multichannel Disc Player Channel InputsYou are now ready to begin enjoying your new receiver Adjust Lip SyncOperation Volume ControlDolby Volume Dolby Volume Calibration OffsetAudio Effects Sleep TimerHeadphones Mute FunctionRDS Display Options Using the TunerRDS Tuning RDS OperationInternet Radio USB PlaybackRecording Using Docking StationUsing The Bridge Network PlaybackSelect Next Screen IPod manual modeUsing The Bridge II in iPod Manual Mode Select MenuSelecting a Surround Mode Memory Troubleshooting GuideProcessor Reset Device Type Appendix Default settingsAppendix Table A1 Recommended Source Component ConnectionsTable A2 Source Setting Defaults Video Section Technical SpecificationsFM Tuner Section AM Tuner SectionEnglish

660, 760 specifications

Harman-Kardon has long been a name synonymous with high-fidelity audio products, and among its most iconic offerings are the Harman-Kardon 660 and 760 models. These models exemplify the brand's commitment to delivering superior sound quality, cutting-edge technologies, and striking aesthetics.

The Harman-Kardon 660 is recognized for its robust construction and powerful sound output. This model integrates advanced audio technologies such as Harman’s proprietary Harman Tune technology, which optimizes sound performance based on the acoustic environment. This ensures a rich and immersive audio experience, allowing listeners to enjoy their favorite music at its best.

With a sleek design highlighted by its distinctive curves and premium materials, the 660 is not only a practical addition to any audio setup but also a stylish one. It features a powerful amplifier that can drive high-performance speakers, providing a dynamic range that brings music to life. The inclusion of Bluetooth connectivity allows users to stream music effortlessly from their devices, making it suitable for modern listening habits.

On the other hand, the Harman-Kardon 760 takes audio performance to the next level. Building upon the features of its predecessor, the 760 includes an even more powerful amplifier, enhanced audio processing capabilities, and an expanded range of connectivity options. This model supports various audio formats, ensuring compatibility with other high-resolution audio sources and streaming services.

One of the standout characteristics of the 760 is its multi-room capability, which enables users to connect multiple speakers throughout their home. The system can be controlled via a user-friendly app, allowing for seamless navigation and personalized listening experiences. Additionally, the 760 employs advanced DSP (Digital Signal Processing) technology, which further refines audio fidelity and clarity, delivering a studio-quality sound.

Both models feature elegant touch controls and an intuitive interface, making it easy to navigate through playlists and settings. They also prioritize energy efficiency, ensuring that the products are environmentally friendly without sacrificing performance.

In summary, the Harman-Kardon 660 and 760 models represent the pinnacle of audio innovation, combining high-quality sound, stylish design, and modern technology. Whether for casual listening or serious audiophile experiences, these models provide an exceptional audio journey that meets the needs of diverse listeners.
Top Page Image Contents