GE 215c1002p004-4 owner manual Reverse Osmosis Cartridge Replacement

Page 8
Pull the u-pin and remove the inlet cover from the housing.

Care and cleaning of the reverse osmosis system.

Safety Instructions

Operating Instructions

Troubleshooting Tips

Customer Service

Reverse Osmosis Cartridge Replacement

NOTE: When replacing the Reverse Osmosis cartridge, also install a new flow control and screen. See the Flow Control and Screen section.

If the Reverse Osmosis Filtration system is connected to your icemaker YOU MUST turn off the icemaker by raising the feeler arm before servicing the filter, changing the filters, or purging the filtration system. Four hours after servicing your unit, lower the feeler arm to resume icemaking.

When replacing cartridges you may lift the Reverse Osmosis assembly from the mounting washers and lay it on the floor. You can also remove the Reverse Osmosis housing by pulling it out of the mounting clamps.

When the amber “RO” light flashes the Reverse Osmosis cartridge must be replaced. NOTE: Disregard initial or short periods (a few seconds) of the flashing “RO” light. Long periods of limited or non use can cause TDS levels to temporarily change.

Be sure you clean your hands with anti-bacterial soap before handling inner parts of the system.

1 Be sure the water supply valve to the Reverse Osmosis system is turned off, and the RO water faucet and storage tank are open. Allow the system to drain completely (this takes several minutes).

2 Pull the Reverse Osmosis system out away from cabinet. Leave tubing connected. Place a dry towel under the Reverse Osmosis unit. Using pliers remove the lock washer, pull the u-pin and remove the Reverse Osmosis housing inlet cover. Save the lock washer for final assembly.

CAUTION: Failure to close the water supply valve or tank shutoff valve will cause water to spray or run when sumps are removed.

3 Remove the lock washer, pull the u-pin and remove the inlet cover from the housing.

4 Use pliers to pull the cartridge from the housing and discard the cartridge.

5 Sanitize the system. Go to the Sanitizing the Reverse Osmosis System section and follow steps 4 through 11.

6 Install new flow control and screen. Go to the Flow Control and Screen section for directions.

7

8 Install the new Reverse Osmosis cartridge. NOTE: The Reverse Osmosis cartridge o-ring end is notched and may need to be rotated during reinstallation for proper fit.

9 Replace the inlet cover. Lightly lubricate the o-ring seal with only clean silicone grease.

10 Insert the u-pin and install the lock washer.

11 Turn on the water supply. Check for leaks.

12 Purge the Reverse Osmosis system. Go to the Purging the Reverse Osmosis System section.

CAUTION: The Reverse Osmosis cartridge contains a food grade preservative that should be purged from the system before first use or whenever the Reverse Osmosis cartridge is replaced. The preservative will give product water an unpleasant taste and odor. After the tank has filled (takes about four hours), open the system faucet until the bladder is empty. After four of these drainings, the system is ready to make product water for your use.

NOTE: Lights may not operate properly until the system has been allowed to refill the tank.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Reverse Osmosis Part No C1002P004-4 Pub. No -5802-45 -98 CGSafety Information Operating Instructions Staple sales slip or cancelled check hereCongratulations You are Now Part of the GE Family Write the model and serial numbers hereSafety Precautions Specification guidelines About the reverse osmosis systemWhat the Reverse Osmosis System Does Maximum iron, manganese, hydrogen sulfide ppmOperating Instructions Faucet and Indicator Lights Care and cleaning of the reverse osmosis system To obtain replacement filters, call GE Appliance Parts atPrefilter and Postfilter Cartridge Replacement Activated CarbonReverse Osmosis Cartridge Replacement Sanitizing the Reverse Osmosis System Flow Control and Screen Purging the Reverse Osmosis SystemBefore you call for service… Problem Possible Causes What To DoChlorine taste and/or Odor in the ReverseOsmosis product water Other taste and/or odorWe’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration GE Reverse Osmosis System Warranty GE Will Replace, At No Charge To YouWhat GE Will Not Cover Warrantor General Electric Company. Louisville, KYService Telephone Numbers GE Answer Center

215c1002p004-4 specifications

The GE 215C1002P004-4 is a high-performance electronic device that has gained prominence in various industrial and commercial applications. This component is part of General Electric's line of advanced technologies, reflecting the company's ongoing commitment to innovation and reliability.

One of the key features of the GE 215C1002P004-4 is its robust design, which allows it to operate efficiently in demanding environments. The device is engineered to withstand extreme temperatures and harsh conditions, ensuring longevity and dependable performance. This ruggedness makes it suitable for use in sectors such as manufacturing, aerospace, and energy.

In terms of technology, the GE 215C1002P004-4 boasts cutting-edge features that enhance its functionality. It incorporates advanced circuitry that enables precise control and monitoring capabilities. This is crucial for applications where accuracy is paramount, such as in industrial automation systems. The device also supports various communication protocols, making it versatile and compatible with a wide range of existing systems.

Another significant characteristic of the GE 215C1002P004-4 is its energy efficiency. As industries worldwide strive to reduce their carbon footprint and operational costs, the energy-efficient design of this device makes it an attractive option. It optimizes power consumption while maintaining high performance levels, aligning with modern sustainability goals.

The user interface of the GE 215C1002P004-4 is designed to be intuitive, facilitating easy operation and monitoring. This ease of use is crucial for technicians and operators who need to access real-time data and diagnostics to ensure optimal performance and quick troubleshooting.

Furthermore, the GE 215C1002P004-4 is compliant with various industry standards, ensuring that it meets rigorous safety and quality requirements. This compliance reinforces its reliability and bolsters customer confidence in its performance.

In conclusion, the GE 215C1002P004-4 is a versatile and efficient electronic device that stands out due to its rugged design, advanced technology, energy efficiency, and user-friendly interface. As industries continue to evolve, components like the GE 215C1002P004-4 play a vital role in driving innovation and improving operational efficiency across various sectors. Whether used in automation, control systems, or other applications, it exemplifies the quality and reliability that General Electric is known for.
Top Page Image Contents