Harman-Kardon AVR 7550HD owner manual Main Remote Control Functions

Page 14

MAIN REMOTE CONTROL FUNCTIONS

Light: Press to illuminate the buttons on the remote. Press it again to turn the back light off, or wait 10 seconds after the last button press for the light to turn off on its own.

Disc Menu: While a DVD is playing, press the DVD Source

Selector, then this button, to display the disc’s menu.

Soft Keys: These buttons are used to select sources A, B, C and D (see note on page 13), or for other functions with some source devices. See Table A14 in the appendix for details. They are also used with a Teletext-capable television if your broadcast, cable or satellite provider offers Teletext service.

Volume Control: Press to raise or lower the volume.

Mute Button: Press to mute the AVR 7550HD’s speaker and headphone outputs. To end the muting, press this button, adjust the volume, or turn off the receiver.

Channel/Page Control: When the tuner has been selected, this control changes the station. When using The Bridge II or a USB drive, this control allows you to scroll a page at a time through a long list of content. While operating a cable, satellite or HDTV set- top box or a television, press these buttons to change channels.

Transport Controls: These buttons are used to control source playback.

Record Button: Use this button to make recordings when an audio or video recorder is in use.

AVR Settings/Remote Menu Button: Press to display the AVR’s Main Menu, or to switch the remote to AVR device mode. Press and hold for 3 seconds to access the menu for the remote control. The menu commands and options will appear in the LCD Display.

The functions are: program the codes for a device, learn codes for an individual key, change the device type of a selector, program an activity (macro), program punch-through functions for channel control or transport control, rename a device or a key’s function, change the brightness of the back light, reset the remote to its factory-default status, or exit the remote menu. See the Initial Setup section for details on programming the remote, and see the Advanced Functions section for further information.

Info Settings Button: Press to display the AVR’s Info Menu, which contains the settings for the current source.

Source Settings Button: Press a Source Selector and then this button to display a source device’s settings menu.

Sleep Settings Button: Press to activate the sleep timer, which turns off the receiver after a programmed period of time of up to 90 minutes. Each press decreases the timer by 10 minutes, ending with the “Sleep Off” message.

Zone Selector: Use this switch to select whether AVR commands will affect the main listening area (Zone 1) or the remote zone of a multizone system (Zone 2). For normal operation, leave the switch in the Zone 1 position.

14

Image 14
Contents AVR7550HD Service Instructions Outdoor Use Marking Safety InformationImportant Safety Instructions Wet Location MarkingImportant Safety Information UnpackingTable of Contents Introduction Surround ModesAudio/Video Inputs Supplied AccessoriesAudio Inputs Digital Audio InputsFRONT-PANEL Controls Back/ExitOn When the AVR is turned on, this LED turns white Resolution setting 480i, 480p, 720p, 1080i or 1080pREAR-PANEL Connections Video Hdmi 1, 2, 3 Output XM AntennaREAR-PANEL Connections Front, Center and Surround Speaker Outputs Zone Selector Main Remote Control FunctionsAVR Power On Main Remote Control Functions Main Remote Control Functions IR Transmitter Mute Zone 2 Remote Control FunctionsSleep Settings MenuZone 2 Remote Control Functions Multichannel Audio Introduction to Home TheaterTypical Home Theater System Harman International the Harman Kardon parent company LogicSpeaker Connections Connecting Source Devices to the AVRConnections SubwooferAnalog Audio Video ConnectionsIncluding Dolby TrueHD and DTS-HD Master Audio Digital VideoAntennas RS-232 Serial PortSubwoofer Placement Speaker PlacementFront Speaker Placement Source Assignment Worksheet Getting StartedBest audio connection for each source For Getting Started Installation Connect IR Control Devices to the Zone 2 IR Input Step Eleven Install a Multizone SystemConnect a Video Display Device or Switcher Select one or all of these methods for audio distributionStep Fourteen Program Sources Into the Remote Step Twelve Plug in AC Power CordsStep Thirteen Insert Batteries in Remote To program the codes for a source device into the remoteTo delete a programmed or learned code To change the device type of a Source SelectorTo learn individual key codes To rename a key or deviceStep Fifteen Turn On the AVR 7550HD Configure the AVR 7550HD, Using EzSet/EQ II Technology Initial SetupUsing the ON-SCREEN Menu System Select Automatic Setup-EzSet/EQSet Up Sources Audio and Video Input SelectionChannel Inputs You are now ready to begin enjoying your new receiver Dolby Volume Calibration Offset Volume ControlDolby Volume OperationUsing the Tuner Sleep TimerHeadphones Mute FunctionXM Radio Operation Video display is in useTo return to the beginning of the current track, press USB PlaybackInternet Radio Network Playback Using Docking StationUsing The Bridge IPod Function Remote Control Key RecordingPlay Pause Menu Back/Exit or Left Arrow Select IPod Manual ModeTV Out setting to take effect Next Track Next 33 Previous Track Previous ISelecting a Surround Mode Surround Modes MenuAdvanced Functions Analog Audio SignalsDigital Audio Signals Audio Processing and Surround SoundVideo Game Logic 7 Game Dolby Surround SettingsManual Speaker Setup Step TWO Measure Speaker Distances Step Three Manual Setup MenuStep ONE Determine Speaker Crossover Number of SpeakersSub Mode Adjust Crossover Frequencies MenuAdjust Speaker Distance Menu Step Four Setting Channel Output Levels Manually Video Adjustments Video ModesHow to Adjust the Custom Picture Settings System Settings Sharpness AdjustmentMenu Appearance General AVR SettingsAdvanced Remote Control Functions System InformationActivities Macros To end the command sequence, press the OK ButtonMain Menu Punch-Through Programming Remote ResetBack Light Processor Reset MemoryTroubleshooting Guide Symptom Cause SolutionTable A1 Recommended Source Component Connections Table A2 Source Setting DefaultsAppendix Table A3 Speaker/Channel Setting Defaults Table A20mS Table A4 Delay Setting DefaultsTable A5 Source Settings BridgeTable A5 Table A6 Audio Effects SettingsDefault Table A6Table A7 Table A7 Video Modes SettingsOff Black Level Deinterlacing Film Mode Detect 302 Table A8 Table A9 Remote Control CodesTable A8 Surround Modes Source Input Device Type if changedTable A12 Zone 2 Settings Table A10 System SettingsTable A11 Network Settings Surround Mode Description Incoming Bitstream or Signal Table A13 Surround ModesTable A13 Presentation DTS Neo6 DTS-ES MatrixDTS Stereo DTS 2/2/.0 or .1, 3/2/.0 orAnalog Bypass For multichannelSubwoofer is used Remote Control Function List Reference Table A14 Remote Control Function List RadioTable A14 AUXAVR 7550HD Technical Specifications Audio Section