Harman-Kardon AVR 7550HD owner manual Processor Reset, Memory

Page 51

ADVANCED FUNCTIONS

PROCESSOR RESET

If the unit behaves erratically after a power surge, first turn off the Main Power Switch and unplug the AC power cord for at least 3 minutes. Plug the cord back in and turn the receiver on. If this doesn’t help, reset the AVR.

NOTE: A system reset erases all user configurations, including video resolution, speaker and level settings, and tuner presets. After a reset, reenter all of these settings from your notes in the appendix worksheets.

To reset the AVR 7550HD, place it in Standby mode (press the front- panel Standby/On Switch so that the Power Indicator turns amber). Then press the front-panel AVR Settings and Source List Buttons simultaneously until the RESET message appears.

If the receiver does not function correctly after a processor reset, contact an authorized Harman Kardon service center for assistance. Authorized service centers may be located by visiting the Web site at www.harmankardon.com.

NOTE: After performing a system reset, wait at least 1 minute before pressing any Source Selectors. If The Bridge Source Selector is pressed too soon, video playback from the iPod will not be available.

MEMORY

If the AVR 7550HD is unplugged or experiences a power outage, it will retain user settings for up to four weeks.

51

Image 51

Contents AVR7550HD Wet Location Marking Safety InformationImportant Safety Instructions Service Instructions Outdoor Use MarkingUnpacking Important Safety InformationTable of Contents Surround Modes IntroductionDigital Audio Inputs Supplied AccessoriesAudio Inputs Audio/Video InputsBack/Exit FRONT-PANEL ControlsResolution setting 480i, 480p, 720p, 1080i or 1080p On When the AVR is turned on, this LED turns whiteVideo Hdmi 1, 2, 3 Output XM Antenna REAR-PANEL ConnectionsREAR-PANEL Connections Front, Center and Surround Speaker Outputs Main Remote Control Functions AVR Power OnZone Selector Main Remote Control Functions Main Remote Control Functions Menu Zone 2 Remote Control FunctionsSleep Settings IR Transmitter MuteZone 2 Remote Control Functions Harman International the Harman Kardon parent company Logic Introduction to Home TheaterTypical Home Theater System Multichannel AudioSubwoofer Connecting Source Devices to the AVRConnections Speaker ConnectionsDigital Video Video ConnectionsIncluding Dolby TrueHD and DTS-HD Master Audio Analog AudioRS-232 Serial Port AntennasSpeaker Placement Front Speaker PlacementSubwoofer Placement Getting Started Best audio connection for each source ForSource Assignment Worksheet Getting Started Installation Select one or all of these methods for audio distribution Step Eleven Install a Multizone SystemConnect a Video Display Device or Switcher Connect IR Control Devices to the Zone 2 IR InputTo program the codes for a source device into the remote Step Twelve Plug in AC Power CordsStep Thirteen Insert Batteries in Remote Step Fourteen Program Sources Into the RemoteTo rename a key or device To change the device type of a Source SelectorTo learn individual key codes To delete a programmed or learned codeStep Fifteen Turn On the AVR 7550HD Select Automatic Setup-EzSet/EQ Initial SetupUsing the ON-SCREEN Menu System Configure the AVR 7550HD, Using EzSet/EQ II TechnologyAudio and Video Input Selection Set Up SourcesChannel Inputs You are now ready to begin enjoying your new receiver Operation Volume ControlDolby Volume Dolby Volume Calibration OffsetMute Function Sleep TimerHeadphones Using the TunerVideo display is in use XM Radio OperationUSB Playback Internet RadioTo return to the beginning of the current track, press Recording Using Docking StationUsing The Bridge IPod Function Remote Control Key Network PlaybackNext Track Next 33 Previous Track Previous I IPod Manual ModeTV Out setting to take effect Play Pause Menu Back/Exit or Left Arrow SelectSurround Modes Menu Selecting a Surround ModeAudio Processing and Surround Sound Analog Audio SignalsDigital Audio Signals Advanced FunctionsDolby Surround Settings Manual Speaker SetupVideo Game Logic 7 Game Number of Speakers Step Three Manual Setup MenuStep ONE Determine Speaker Crossover Step TWO Measure Speaker DistancesAdjust Crossover Frequencies Menu Adjust Speaker Distance MenuSub Mode Step Four Setting Channel Output Levels Manually Video Modes Video AdjustmentsHow to Adjust the Custom Picture Settings Sharpness Adjustment System SettingsSystem Information General AVR SettingsAdvanced Remote Control Functions Menu AppearanceTo end the command sequence, press the OK Button Main MenuActivities Macros Remote Reset Back LightPunch-Through Programming Memory Processor ResetSymptom Cause Solution Troubleshooting GuideTable A2 Source Setting Defaults AppendixTable A1 Recommended Source Component Connections Table A2 Table A3 Speaker/Channel Setting DefaultsBridge Table A4 Delay Setting DefaultsTable A5 Source Settings 0mSTable A6 Table A6 Audio Effects SettingsDefault Table A5Table A7 Video Modes Settings Off Black Level Deinterlacing Film Mode Detect 302Table A7 Source Input Device Type if changed Table A9 Remote Control CodesTable A8 Surround Modes Table A8Table A10 System Settings Table A11 Network SettingsTable A12 Zone 2 Settings Table A13 Surround Modes Surround Mode Description Incoming Bitstream or SignalTable A13 DTS 2/2/.0 or .1, 3/2/.0 or DTS-ES MatrixDTS Stereo Presentation DTS Neo6For multichannel Subwoofer is usedAnalog Bypass Remote Control Function List Reference Radio Table A14 Remote Control Function ListAUX Table A14Audio Section AVR 7550HD Technical Specifications