Harman-Kardon owner manual Step Fifteen Turn On the AVR 7550HD

Ad

Page 28

INSTALLATION

Use the 7Button to move the cursor to the beginning of the name, then type over the current name using the Alphanumeric Keys.

Each Alphanumeric Key has the characters available in addition to its number printed above the key. Each press of the key scrolls through the available characters. To move to the next character, either press the 3Button or press the next desired Alphanumeric Key.

Press the OK Button to finish, and the remote will prompt you to rename another key or device, or to exit.

STEP FIFTEEN – Turn On the AVR 7550HD

Two steps are required the first time you turn on the AVR 7550HD.

1.Flip down the Front-Panel Door and press the Main Power Switch in. The Power Indicator on the front panel will turn amber, indi- cating that the AVR is in Standby mode and is ready to be turned on. Normally, you may leave the Main Power Switch on, even when the receiver is not being used.

2.There are several ways to turn on the AVR from Standby mode.

a)Press the Standby/On Switch on the front panel.

b)Using the remote, press the AVR Power On Button or any of the Source Selectors.

NOTES:

•Any time you press one of the Source Selectors on the remote, the remote will switch device modes. To control the receiver, press the AVR Settings Button. Some AVR functions are available in all device modes: Volume Controls (including Mute), Audio Effects, Video Modes, Surround Modes, AVR Settings, Info Settings, Sleep Settings and AVR Power On and Off.

•If you do not see a picture within about 1 minute, refer to the Video Troubleshooting Tips on page 34.

28

Image 28

Contents AVR7550HD Safety Information Important Safety InstructionsService Instructions Outdoor Use Marking Wet Location MarkingImportant Safety Information UnpackingTable of Contents Introduction Surround ModesSupplied Accessories Audio InputsAudio/Video Inputs Digital Audio InputsFRONT-PANEL Controls Back/ExitOn When the AVR is turned on, this LED turns white Resolution setting 480i, 480p, 720p, 1080i or 1080pREAR-PANEL Connections Video Hdmi 1, 2, 3 Output XM AntennaREAR-PANEL Connections Front, Center and Surround Speaker Outputs AVR Power On Main Remote Control FunctionsZone Selector Main Remote Control Functions Main Remote Control Functions Zone 2 Remote Control Functions Sleep SettingsIR Transmitter Mute MenuZone 2 Remote Control Functions Introduction to Home Theater Typical Home Theater SystemMultichannel Audio Harman International the Harman Kardon parent company LogicConnecting Source Devices to the AVR ConnectionsSpeaker Connections SubwooferVideo Connections Including Dolby TrueHD and DTS-HD Master AudioAnalog Audio Digital VideoAntennas RS-232 Serial PortFront Speaker Placement Speaker PlacementSubwoofer Placement Best audio connection for each source For Getting StartedSource Assignment Worksheet Getting Started Installation Step Eleven Install a Multizone System Connect a Video Display Device or SwitcherConnect IR Control Devices to the Zone 2 IR Input Select one or all of these methods for audio distributionStep Twelve Plug in AC Power Cords Step Thirteen Insert Batteries in RemoteStep Fourteen Program Sources Into the Remote To program the codes for a source device into the remoteTo change the device type of a Source Selector To learn individual key codesTo delete a programmed or learned code To rename a key or deviceStep Fifteen Turn On the AVR 7550HD Initial Setup Using the ON-SCREEN Menu SystemConfigure the AVR 7550HD, Using EzSet/EQ II Technology Select Automatic Setup-EzSet/EQSet Up Sources Audio and Video Input SelectionChannel Inputs You are now ready to begin enjoying your new receiver Volume Control Dolby VolumeDolby Volume Calibration Offset OperationSleep Timer HeadphonesUsing the Tuner Mute FunctionXM Radio Operation Video display is in useInternet Radio USB PlaybackTo return to the beginning of the current track, press Using Docking Station Using The Bridge IPod Function Remote Control KeyNetwork Playback RecordingIPod Manual Mode TV Out setting to take effectPlay Pause Menu Back/Exit or Left Arrow Select Next Track Next 33 Previous Track Previous ISelecting a Surround Mode Surround Modes MenuAnalog Audio Signals Digital Audio SignalsAdvanced Functions Audio Processing and Surround SoundManual Speaker Setup Dolby Surround SettingsVideo Game Logic 7 Game Step Three Manual Setup Menu Step ONE Determine Speaker CrossoverStep TWO Measure Speaker Distances Number of SpeakersAdjust Speaker Distance Menu Adjust Crossover Frequencies MenuSub Mode Step Four Setting Channel Output Levels Manually Video Adjustments Video ModesHow to Adjust the Custom Picture Settings System Settings Sharpness AdjustmentGeneral AVR Settings Advanced Remote Control FunctionsMenu Appearance System InformationMain Menu To end the command sequence, press the OK ButtonActivities Macros Back Light Remote ResetPunch-Through Programming Processor Reset MemoryTroubleshooting Guide Symptom Cause SolutionAppendix Table A2 Source Setting DefaultsTable A1 Recommended Source Component Connections Table A3 Speaker/Channel Setting Defaults Table A2Table A4 Delay Setting Defaults Table A5 Source Settings0mS BridgeTable A6 Audio Effects Settings DefaultTable A5 Table A6Off Black Level Deinterlacing Film Mode Detect 302 Table A7 Video Modes SettingsTable A7 Table A9 Remote Control Codes Table A8 Surround ModesTable A8 Source Input Device Type if changedTable A11 Network Settings Table A10 System SettingsTable A12 Zone 2 Settings Surround Mode Description Incoming Bitstream or Signal Table A13 Surround ModesTable A13 DTS-ES Matrix DTS StereoPresentation DTS Neo6 DTS 2/2/.0 or .1, 3/2/.0 orSubwoofer is used For multichannelAnalog Bypass Remote Control Function List Reference Table A14 Remote Control Function List RadioTable A14 AUXAVR 7550HD Technical Specifications Audio Section