PROGRAMMING THE REMOTE
The AVR 135 is equipped with a powerful remote control that will control not only the receiver’s func- tions, but also most popular brands of audio and video equipment, including CD players, cassette decks, TV sets, cable boxes, VCRs, satellite receivers and other home theater equipment. Once the AVR 135’s remote is programmed with the codes for the products you own, it is possible to eliminate most other remotes and replace them with the convenience of a single, universal remote control.
Programming Device Codes
The AVR 135 remote is
Direct Code Entry
This method is the easiest way to program your remote to work with different products.
1.Use the tables in the following pages to determine the
2.Turn on the unit you wish to program into the AVR 135 remote.
3.Press and hold both the Input Selector e for the product you wish to control (e.g., VCR, TV) and
the Mute Button 
42 at the same time. When the red light under the Input Selector e stays lit and the Program Indicator c turns amber and begins flashing, release the buttons. It is important that you begin the next step within 20 seconds.
4.Point the AVR 135’s remote toward the unit to be programmed, and enter the first
5.If the device to be programmed in does NOT turn off, continue to enter
6.Try all of the functions on the remote to make cer- tain that the product operates properly. Keep in mind that many manufacturers use a number of
different combinations of codes, so it is a good idea to make certain that not only the power control, but the volume, channel and transport controls work as they should. If functions do not work properly, you may need to use a different remote code.
7.If a code cannot be entered to turn the unit off, if the code for your product does not appear in the tables in this manual, or if not all functions oper- ate properly, try programming the remote with the Auto Search Method.
Auto Search Method
If the unit you wish to include in the AVR 135’s remote is not listed in the code tables in this manual or if the code does not seem to operate properly, you may wish to program the correct code using the Auto Search method that follows:
1.Turn on the unit that you wish to include in the AVR 135 remote.
2.Press the Input Selector efor the type of
product to be entered (e.g., VCR, TV) and the
Mute Button 
41 at the same time. Hold both buttons until the red light under the Input Selector estays lit and the Program Indicator cturns amber and begins flashing. The next step must take place while the red light is on, and it must begin within 20 seconds after the light appears.
3.Point the AVR 135 remote toward the unit to be programmed, and press either the ⁄ or ¤ Button nrepeatedly. Each press will send out a series of codes from the remote’s
4.Press the Input Selector e; the red light under the Input Selector will flash three times before going dark to confirm the entry.
5.Try all of the functions on the remote to make cer- tain that the product operates. Keep in mind that many manufacturers use a number of different combinations of codes, and it is a good idea to make certain that not only the power control works, but also the volume, channel and transport controls, as appropriate. If all functions do not work properly, you may need to
Code Readout
When the code has been entered using the Auto Search method, it is always a good idea to find out the exact code so that it may be easily reentered if neces- sary. You may also read the codes to verify which device has been programmed to a specific Control Selector button.
1.Press and hold both the Input Selector e for the device you wish to find the code for and
the Mute Button 
41 at the same time. The Program Indicator c will turn amber and begin flashing, and the red light under the Input Selector e will stay lit. Release the buttons and begin the next step within 20 seconds.
2.Press the Set Button p. The Program Indicator cwill then blink green in a sequence that corresponds to the
Example: One blink, followed by a
For future reference, enter the setup codes for the equipment in your system here:
DVD | ____________ CD ________________ |
VID1/VCR __________ VID2/TV __________ | |
VID3/CBL ________ VID3/SAT __________ | |
TAPE | ______________________________ |
Macro Programming
Macros enable you to easily repeat frequently used combinations of commands with the press of a single button on the AVR 135’s remote control. Once pro- grammed, a macro will send out up to 19 different remote codes in a predetermined sequential order enabling you to automate the process of turning on your system, changing devices, or other common tasks. The AVR 135’s remote can store up to five separate macro command sequences: one that is associated with the Power On Button aand four more that are accessed by pressing the Macro Buttons 30 .
1. Press the Mute Button 
41 and the Macro Button 30 to be programmed or the Power On Button a at the same time. An Input Selector efwill light red, and the Program Indicator c will flash amber.
2.Enter the steps for the macro sequence by press- ing the button for the actual command step. Although the macro may contain up to 19 steps, each button press, including those used to change devices, counts as a step. The Program Indicator
30 PROGRAMMING THE REMOTE