APPENDIX
Troubleshooting
If the machine stops working properly, check the following possible problems.
If the problem is still there, contact your retailer or the nearest authorized service center.
Symptom | Possible cause | How to put it right | Reference | |
| The machine is not plugged in. | Plug the machine in. | page 7 | |
|
|
|
| |
The sewing | The main power switch is turned off. | Turn on the main power switch. | page 8 | |
|
|
| ||
The | Move the |
| ||
machine does | page 17 | |||
not work. | to the right. | left. | ||
| ||||
| You have not used the foot control- | Use the foot controller properly. | page 8 | |
| ler properly. | |||
|
|
| ||
|
|
|
| |
| The needle is not fitted properly. | Fit the needle properly. | page 8 | |
|
|
|
| |
| The needle clamp screw is loose. | Use the screwdriver to firmly tighten | page 9 | |
| the screw. | |||
|
|
| ||
|
|
|
| |
| The needle is bent or blunt. | Replace the needle. | page 8 | |
|
|
|
| |
| You have not used the right combi- | Choose a thread and needle that are | page 26 | |
| nation of fabric, thread and needle. | appropriate for the type of fabric. | ||
|
| |||
|
|
|
| |
| The presser foot you are using is not | Attach the presser foot that is correct | – | |
| appropriate for the type of stitch that | for the type of stitch that you want to | ||
| you want to sew. | sew. |
| |
|
|
|
| |
| The upper thread tension is too tight. | Loosen the upper thread tension. | page 25 | |
|
|
|
| |
The needle | You are pulling the fabric too much. | Lightly guide the fabric. | – | |
|
|
| ||
breaks. | You have not fitted the spool properly. | Fit the spool properly. | page 21, 25 | |
|
|
|
| |
| The area around the hole in the nee- | Replace the needle plate. | – | |
| Contact your retailer or the nearest | |||
| dle plate is scratched. | authorized service center. |
| |
|
|
| ||
|
|
|
| |
| The area around the hole in the | Replace the presser foot. | – | |
| Contact your retailer or the nearest | |||
| presser foot is scratched. | |||
| authorized service center. |
| ||
|
|
| ||
|
|
|
| |
|
| Replace the bobbin case. | – | |
| The bobbin case is scratched. | Contact your retailer or the nearest | ||
|
| authorized service center. |
| |
|
|
|
| |
| You have not used a bobbin that has | Incorrect bobbins will not work |
| |
| properly. Only use a bobbin that has | page 16 | ||
| been designed for this machine. | |||
| been designed for this machine. |
| ||
|
|
| ||
|
|
|
| |
| You have not threaded the upper |
|
| |
| thread properly. (For example, you |
|
| |
| have not fitted the spool properly, or | Correct the upper threading. | page 21 | |
| the thread has come out of the guide |
|
| |
| above the needle.) |
|
| |
|
|
|
| |
| There are knots or tangles in the | Remove any knots or tangles. | – | |
| thread. | |||
|
|
| ||
|
|
|
| |
The upper | The needle is not appropriate for the | Choose a needle that is appropriate | page 26 | |
thread you are using. | for the type of stitch. | |||
thread breaks. |
|
|
| |
The | Loosen the upper thread tension. | page 25 | ||
| ||||
|
|
|
| |
|
| Remove the tangled thread. If the |
| |
| The thread is tangled. | thread is tangled in the bobbin case, | page 44 | |
|
| clean the bobbin case. |
| |
|
|
|
| |
| The needle is bent or blunt. | Replace the needle. | page 8 | |
|
|
|
| |
| You have not inserted the needle | Insert the needle properly. | page 8 | |
| properly. | |||
|
|
| ||
|
|
|
|
46