Brother 885-S25/S27 operation manual Threading the Machine, Winding the Bobbin

Page 18

KNOWING YOUR SEWING MACHINE ———————————————————————————————————————

THREADING THE MACHINE

Winding the Bobbin

CAUTION

●Only use bobbins (part code: SA156, SFB (XA5539-151)) that have been designed for this sewing machine. Using other bobbins may cause damage to the machine.

●We designed the bobbin that comes with this machine. If you use bobbins from other models, the machine will not work properly. Only use the bobbin that comes with this machine or bobbins of the same type (part code: SA156, SFB (XA5539-151)).

Actual size

11.5mm (7/16 inch)

This model

Other models

1

2

1Pre-tension disk

2Bobbin winder shaft

1Put the spool of thread on the spool pin and pass the thread around the pre-tension disk.

CAUTION

●If the spool of thread is not in the right place, the thread may tangle on the spool pin.

2Pass the end of the thread through the hole on the bobbin from the inside of the bobbin.

3Put the bobbin onto the bobbin winder shaft and slide the bobbin winder shaft to the right. Turn the bobbin clockwise, by hand, until the spring on the shaft slides into the groove of the bobbin.

2

1

1Spring on the shaft

2 Groove of the bobbin

16

Image 18

Contents Appendix Important Safety Instructions For Users in the UK, EIRE, Malta and Cyprus only UNPACKING/REPACKING Instructions Please Read These Instructions Before YOU USE the MachineContents Appendix Knowing Your Sewing Machine Main PartsAccessories Optional AccessoriesUsing Your Sewing Machine Connecting PlugsChecking the Needle Main Power and Sewing Light SwitchFoot Controller Replacing the NeedleChanging the Presser Foot Touches the stopper, and securely tighten1Slideopen theit. flat bed attachment to the left to Using a Free-arm StyleFlat Bed Attachment 1Slide the flat bed attachment to the left to release itControls Pattern Selection DialStitches Width Patterns and Stitch NamesPattern Recommended Instruction Manual3/16 Fixed 3/32 Stitch Length Dial Reverse Sewing Lever Stretch StitchingStitch Width Dial Stitches Selecting a Stretch StitchThreading the Machine Winding the BobbinWound evenly Wound poorly Lower Threading Lower Threading for models equipped with a quick-set bobbin Follow steps 1 and 2 from Lower Threading Raise the presser foot using the presser foot lever Upper Threading6Putneedle.the thread behind the guide above Hook Thread Drawing up the Lower Thread Sewing with a Twin NeedleThread Tension Size FABRIC, THREAD, and Needle CombinationsFabric Type Thread Size of Needle MediumPattern Please Read Before SewingStraight Stitching Fixed 16-0Zigzag Stitch Zigzag StitchingStitch Stitch Name Zigzag StitchStitch Blind Hem StitchingShell Tuck Stitching 3/16Elastic Stitching 4Sew at a slow speedElastic Stitch Overedge Stitching Double Action StitchingPatchworking StitchFeather Stitching Triple Zigzag Stretch StitchingFixed 3/16 Decorative Stitching Making a Buttonhole Stitch PatternPattern Adjusting Buttonholes Sewing Buttons OtherUsing Attachments and Applications Zipper InsertionFoot GatheringDarning Stitch AnyStitch Width AppliquésMonogramming Embroidering Zigzag Stitch AnyKeep fingers away from moving parts, especially needles Optional Accessories Using the Walking FootUsing the Quilting Foot Stitch PlateUsing the 1/4-inch Quilting Foot 16-3/32Quickly Stitch Together a Quilt Changing the Light Bulb MaintenanceCleaning Put the light cover back on and fasten the screw0Install the needle plate cover Troubleshooting Symptom Possible cause How to put it right ReferenceThread ten LowerOr breaks Fabric isThere is a high Stitches areSkipped Pitched noise While sewingIndex NumericsEnglish