Kenmore 625.348670 Optional Adjustable Settings, Gallon or Liter readings defaults to gallons

SECTION 2

HOW YOUR WATER SOFTENER WORKS

2A. FACEPLATE TIMER FEATURES

OPTIONAL ADJUSTABLE SETTINGS

Following is a list of other timer features that are adjustable, and the default setting for each. The defaults automatically set when electrical power is applied to the timer. If you want to change from any of the default values, scroll through steps 1 - 5 below, and reset as desired.

1.Press and hold the #1 SELECT button for 3 seconds until the faceplate display changes. Then, press and release the #1 SELECT button to display 12 hr.

"12 or 24 Hour clock - defaults to 12 hr: At the 12 hr default setting, all time displays are shown in standard clock time (1 to 12 PM; and 1 to 12 AM). If military time displays are desired (0100, 0200, etc.), set to 24 hr by pressing the UP button.

SALTSIGNAL		AM	SALTSIGNAL
LEVELLEVEL			LEVELLEVEL
8		PM	8
7	TIME		7	TIME
6			6
5			5
4			4
3			3
2			2
1			1

2.Press #1 SELECT BUTTON

"Gallon or Liter readings - defaults to gallons:

Water usage and flow displays are shown in gallons. If you prefer to have the same displays in liters, press the UP button until Liter shows.

SALTSIGNAL				SALTSIGNAL
LEVELLEVEL				LEVELLEVEL
8			8
7		7
6	6
5				5
4	4
3	3
2	2
1	1				LITERS

GALLONS

3.Press #1 SELECT BUTTON

"Maximum Days Between Regenerations - default is zero days: The faceplate timer automati- cally controls regeneration frequency (see page 14). This provides the greatest operating efficiency, and normally the maximum days feature is not needed. If you want to be certain a regeneration will

occur within a number of days, use this feature. For example, if your water supply contains iron and you want the softener to regenerate at least once every few days to keep the resin bed clean, set the display as typically shown below. Setting is available from 1 to 15 days by using the UP and DOWN buttons.

NOTE:

Setting a number in this display may override the function of the water meter and timer computer (see page 15). For example, assume the meter/computer would initiate softener regenerations every 6 or 7 days. If you have max days set to 4, as shown below, regenerations will occur every 4 days instead of every 6 or 7.

SALTSIGNAL			SALTSIGNAL
LEVELLEVEL			LEVELLEVEL
8		DAY	8		DAY
7			7
6	RECHARGE		6	RECHARGE		example: set to
5			5
4			4			4 days maxi-
3			3
2			2			mum between
1			1			regenerations
default display

4.Press #1 SELECT BUTTON

"CLEAN feature minutes - default is 7 minutes:

If you have set this feature to ON (page 7), the length of the extra backwash cycle automatically sets to 7 minutes. However, you can adjust this time from 1 to 15 minutes in length. If you have a minimum of iron or sediments, a 3 or 4 minute clean cycle may be enough to keep the resin bed clean. If you have a higher amount of iron or sediments, a setting of over 7 minutes may be needed. To change this cycle time, use the UP button to increase the time, or the DOWN button to shorten the time.

SALTSIGNAL					SALTSIGNAL
LEVELLEVEL			MIN		LEVELLEVEL		MIN
8					8
7		CLEAN			7	CLEAN
6					6
5		TIME			5	TIME
4					4
3					3
2					2
1					1
	default minutes			example: time set to 3 minutes

5.Press #1 SELECT to return the present time display.

11