Kenmore 625.348670 Manual Advance Regeneration Check, Cycle Flow Rates Gallons PER MIN

Page 24

SECTION 5

SERVICE TECH. INFORMATION

5A.TROUBLESHOOTING

MANUAL ADVANCE REGENERATION CHECK

This check verifies proper operation of the valve motor, brine tank fill, brine draw, regeneration flow rates, and other controller functions. Always make the initial checks, and the manual initiated diag- nostics.

NOTES: The faceplate display must show a steady time (not flashing). If an Error code shows, first press the #1 SELECT button to enter the diagnostic display.

1.Press the ON/OFF-HOLD button and hold in for 3 seconds. RECHARGE NOW and FILL begin to flash (or clean backwash begins, if set) as the softener enters the fill cycle of regeneration. When FILL is on steady, remove the brinewell cover and, using a flashlight, observe fill water entering the tank.

a.If water does not enter the tank, look for an ob- structed nozzle, venturi, fill flow plug, brine tub- ing, or brine valve riser pipe.

CYCLE FLOW RATES (GALLONS PER MIN.)

FILL (flow to salt storage tank)

0.3 (1.1 liters)

BRINING

 

.16 (.61 liters)

BRINE RINSE

(flow to drain)

.12 (.45 liters)

BACKWASH

1.8 (6.8 liters)

FAST RINSE

 

1.8 (6.8 liters)

2.After observing fill, press the ON/OFF-HOLD button to move the softener into brining. A slow flow of water to the drain will begin. Verify brine draw from the brine tank by shining a flashlight into the brinewell and observing a noticeable drop in the liquid level.

NOTE: Be sure a salt bridge is not preventing water with salt contact.

a.If the softener does not draw brine¼

¼nozzle and/or venturi dirty or defective.

¼nozzle and venturi not seated properly on gasket.

¼restricted drain (check drain fitting and hose).

¼defective nozzle and venturi seal.

¼other inner valve defect (rotor seal, rotor & disc, wave washer, etc.).

NOTE: If water system pressure is low, an elevated drain hose may cause back pressure, stopping brine draw.

3.Again press ON/OFF-HOLD to move the soften- er into backwash. Look for a fast flow of water from the drain hose.

a.An obstructed flow indicates a plugged top dis- tributor, backwash flow plug, or drain hose.

4.Press ON/OFF-HOLD to move the softener into fast rinse. Again look for a fast drain flow. Allow the softener to rinse for a few minutes to flush out any brine that may remain in the resin tank from the brining cycle test.

5.To return the softener to service, press ON/OFF- HOLD.

BRINE VALVE

FLOAT SETTING

10”

(Distance from top of resin tank, to top of resin bed.)

FREEBOARD 7”-- 11”

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model no Save this ManualWarranty Full TEN Year Warranty Against LeaksFull Three Year Electronics Warranty Full ONE Year Warranty on Water SoftenerTable of Contents Service Tech InformationRepair Parts Softener Start UPWater Softener START-UP Safety Guides SectionPlastic Water Softener START-UP Program the Timer SET Present Time of DAYSET Water Hardness Number Water Softener START-UP 1C.PROGRAM the Timer SET Clean Feature OptionSET Recharge Regeneration Time Water Softener START-UP 1D. Sanitizing the Water Softener ADD WaterWater Softener START-UP 1E. Fill the Storage Tank with Salt ADD SaltHOW Your Water Softener Works 2A. Faceplate Timer Features Extra RechargeSalt Monitor System Optional Adjustable Settings Gallon or Liter readings defaults to gallonsHOW Your Water Softener Works Faceplate Timer Features LOW Salt Indicator LightError Code Program MemoryService RegenerationWater Flow Through the Softener in Brining and Brine Rinse Automatic Bypass ElectronicsPlease see page 9 for Salt Filling Directions Salt BridgeCare of Your Softener 3B. Keeping the Water Softener Clean CoversnoteNozzle & Venturi Iron from the Resin BEDCare of Your Softener 3C. Keep the Softener from Freezing Drain Water from the SoftenerProblem Cause Correction No soft waterOther Things to Know 4A. DIMENSIONS/SPECIFICATIONS SingleService Tech Information 5A.TROUBLESHOOTING Wiring SchematicFaceplate Always Make These Initial Checks FirstService TECH. Information 5A.TROUBLESHOOTING Automatic Electronic DiagnosticsManual Initiated Electronics DIAG- Nostics Possible DefectHF32 shows Manual Advance Regeneration Check Cycle Flow Rates Gallons PER MINService Tech Information 5B.ROTARY Valve Service DisassemblyAssembly Servicing the ValveService Cycle Fill CycleBrining and Brine Rinse Cycles Backwash CycleFast Rinse Cycle Service Tech Information Kenmore Water SOFTENER, Model no KEY Part Description NumberBrine Valve Assembly Valve Assembly Parts List Kenmore Water SoftenerPage Page Owners Manual

625.348670 specifications

The Kenmore 625.348670 is a portable dehumidifier designed to improve indoor air quality and provide a comfortable living environment. It is particularly effective in combating excess moisture in homes, especially in areas prone to high humidity such as basements, bathrooms, and laundry rooms.

One of the main features of the Kenmore 625.348670 is its capacity to remove up to 50 pints of moisture from the air per day. This high extraction rate is suitable for rooms up to 4,500 square feet, making it ideal for both residential and commercial applications. The unit is equipped with a built-in humidistat that allows users to set their desired humidity level, automatically turning the dehumidifier on and off as needed to maintain optimal conditions.

The dehumidifier features a user-friendly control panel, complete with an LED display that shows the current humidity level and settings. It also has several operational modes, including continuous operation, allowing for the option of continuous drainage via a drain hose—ideal for areas with persistently high humidity levels. The 625.348670 is designed with convenience in mind, featuring an easy-to-remove water tank for manual drainage when continuous drainage is not an option.

The Kenmore 625.348670 employs advanced technologies for efficient moisture extraction. Its compressor system operates quietly, ensuring minimal disruption in your living space. This unit also emphasizes energy efficiency, working to reduce energy consumption while still effectively controlling humidity levels, which can be a significant advantage in lowering energy bills.

Another characteristic to note is its portability. The unit is designed with built-in handles and caster wheels, allowing easy movement from room to room. Additionally, its compact design ensures it can fit into tighter spaces without sacrificing performance.

Overall, the Kenmore 625.348670 is an excellent solution for anyone looking to control humidity levels in their environment. With its robust design, high moisture removal capacity, user-friendly features, and energy efficiency, it stands as a reliable choice for managing indoor air quality effectively.
Top Page Image Contents