Kenmore 625.34857, 625.34859 owner manual Keep the Softener from Freezing, Drain Water from

Page 17

SECTION 3

CARE OF YOUR SOFTENER

 

3C.

KEEP THE SOFTENER FROM FREEZING

 

 

 

 

If the softener is installed where it could freeze

FIG. 11

DRAIN WATER FROM THE

(summer cabin, lake home, etc.), you must drain all

 

SOFTENER

 

water from it to stop possible freeze damage. To

 

 

 

drain the softener 6

1.Close the shut5off valve on the house main water pipe, near the water meter or pressure tank.

2.Open a faucet in the soft water pipes to vent pressure in the softener.

3.Refer to FIG. 12 on page 19. Move the stem in a single bypass valve to bypass. Close the inlet and outlet valve in a 35valve bypass system, and open the bypass valve. If you want water in the house

 

pipes again, reopen the shut5off valve on the

7. Looking at FIG. 11, lay a piece of 2 inch thick

 

main water pipe.

 

 

 

 

 

board near the floor drain. Move the softener

 

 

 

 

4.

Unplug the transformer at the

wall

outlet.

close to the drain. SLOWLY and CAREFULLY tip

it over until the rim rests on the wood block with

 

Remove the salt hole cover and the main cover.

 

the inlet and outlet over the drain. Do not allow

 

Take off both drain hoses.

 

 

 

 

 

the softener's weight to rest on the inlet and

 

 

 

 

5.

Carefully remove the large holding clips at the

outlet fittings or they will break.

 

 

softener inlet and outlet (see Key No. 61, on page

8. Tip the bottom of the softener up a few inches

 

30). Separate the softener from the adaptors or

 

and hold until all water has drained. Leave the

 

bypass valve.

 

 

 

 

 

softener laying like this until you are ready to use

 

 

 

 

6.

Remove the brinewell cover and disconnect the

it. Plug the inlet and outlet with rags to keep dirt,

bugs, etc. out.

 

brine valve tubing at the nozzle

and

venturi

 

 

assembly (see page 30). Lift the brine valve out of the brinewell. Tip the brine valve upside down to drain out water.

17

Image 17 Contents
Save this Manual Model NOSFull ONE Year Warranty on Water Softener WarrantyFull TEN Year Warranty Against Leaks Sears Installation Policy Sears Installation WarrantyService Tech Information Table of ContentsRepair Parts Softener Start UPSection Water Softener START-UP Safety GuidesBe sure to restart the water heater. See SET Present Time of DAY Water Softener START-UP 1C.PROGRAM the TimerSET Recharge Regeneration Time SET Water Hardness NumberADD Water Water Softener START-UP 1D. Sanitizing the Water SoftenerADD Salt Water Softener START-UP 1E. Fill the Storage Tank with SaltExtra Recharge HOW Your Water Softener Works 2B.FACE Plate Timer FeaturesRecharge NOW Recharge TonightOptional SETTINGS± Clean Feature HOW Your Water Softener Works 2A.FACE Plate Timer FeaturesPosition Indicators Error CodeRegeneration ServiceFill Backwash Brining Fast Rinse Brine Rinse Water Flow Through the Softener in Brining and Brine Rinse Electronics Automatic BypassSalt Bridge When to Refill with SaltPlease see page 9 for Salt Filling Directions Covers Care of Your Softener 3B. Keeping the Water Softener CleanNozzle & Venturi Iron from the Resin BEDSoftener Keep the Softener from FreezingDrain Water from Problem Cause Correction Bypass Valves Other Things to Know 4A.DIMENSIONS/SPECIFICATIONSWater Supply to Water Softener Salt for Water SoftenerWiring Schematic Service TECH. Information 5A.TROUBLESHOOTINGBack of Timer PWA Always Make These Initial Checks FirstAutomatic Electronic Diagnostics Service Tech Information 5A.TROUBLESHOOTINGManual Initiated Electronics Diagnostics Possible DefectSR31 shows IndicatorManual Advance Regeneration Check Disassembly Service TECH. Information 5B.ROTARY Valve ServiceAssembly Servicing the ValveFill Cycle Service CycleBackwash Cycle Brining and Brine Rinse CyclesFast Rinse Cycle Kenmore Water Softeners Inlet ± Outlet Grounding Clamps Brine Valve AssemblyValve Assembly Bypass Installation Valve Model no Parts ListOwners Manual
Related manuals
Manual 32 pages 12.25 Kb