Kenmore 625.34857 Other Things to Know 4A.DIMENSIONS/SPECIFICATIONS, Bypass Valves, Others

Page 19

SECTION 4

OTHER THINGS TO KNOW

4A.DIMENSIONS/SPECIFICATIONS

FIG. 12

BYPASS VALVES

 

 

 

 

 

INCHES

 

CM

 

 

 

 

 

 

 

 

A

Salt Tank Height

40-1/4

 

102.2

 

 

B

Resin Tank Diameter (nominal)

9

 

22.7

 

 

C

Resin Tank Height (nominal)

40

 

101.6

 

 

D

Inlet-Outlet Height

41-1/2

 

105.4

 

 

E

Overall Height

46

 

116.8

 

 

F1

Length

 

19-1/2

 

49.5

 

 

F2

Width

 

16-1/2

 

41.9

 

Ð

Distance between inlet-outlet

3-3/8

 

8.6

 

 

 

center lines

 

 

 

MODEL NO. 625.348570 AND 625.348590

TIMER SR CODE SR31

 

NOTE: Please see the rating decal for water softener operating capacity, salt usage and service flow rate/pres# sure loss performance specifications. Performance specifications are validated by the Water Quality Associa# tion (WQA). The rating decal is located on the rim, under the salt hole cover (see page 28).

WATER SUPPLY TO WATER SOFTENER

MINIMUM WATER SYSTEM FLOW (gpm)

3

MINIMUM-MAXIMUM WATER PRESSURE (psi)

20-120

MAXIMUM WATER TEMPERATURE (°F)

120

MAXIMUM WATER HARDNESS (gpg)

110

MAXMUM ªCLEAR WATERº IRON (ppm)

7

SALT FOR WATER SOFTENER

TYPE OF SALT NEEDED

Nugget/Pellet

ALTERNATE TYPE OF SALT

Pure, evaporated, compacted

 

water softener salt

STORAGE CAPACITY (pounds)

200

OTHERS

TYPE OF ION EXCHANGE MATERIAL (resin)

High Capacity

AMOUNT OF RESIN (cu.ft.)

 

1.0

REGENERATION (RECHARGE) CYCLE TIME (min.)

FILL

 

2.7-10.3

BRINING/BRINE RINSE

 

97-106

BACKWASH

 

7

FAST RINSE

 

3

TOTAL REGENERATION TIME ➀

109.7-126.3

gpm = gallons per minute

psi = pounds per square inch

gpg = grains per gallon

ppm = parts per million

➀Does not include CLEAN feature cycle times if set to ON.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents
Save this Manual Model NOSSears Installation Policy Sears Installation Warranty WarrantyFull ONE Year Warranty on Water Softener Full TEN Year Warranty Against LeaksSoftener Start UP Table of ContentsService Tech Information Repair PartsSection Water Softener START-UP Safety GuidesBe sure to restart the water heater. See SET Present Time of DAY Water Softener START-UP 1C.PROGRAM the TimerSET Recharge Regeneration Time SET Water Hardness NumberADD Water Water Softener START-UP 1D. Sanitizing the Water SoftenerADD Salt Water Softener START-UP 1E. Fill the Storage Tank with SaltRecharge Tonight HOW Your Water Softener Works 2B.FACE Plate Timer FeaturesExtra Recharge Recharge NOWError Code HOW Your Water Softener Works 2A.FACE Plate Timer FeaturesOptional SETTINGS± Clean Feature Position IndicatorsFill Backwash Brining Fast Rinse Brine Rinse ServiceRegeneration Water Flow Through the Softener in Brining and Brine Rinse Electronics Automatic Bypass Please see page 9 for Salt Filling Directions When to Refill with Salt Salt Bridge Iron from the Resin BED Care of Your Softener 3B. Keeping the Water Softener CleanCovers Nozzle & VenturiDrain Water from Keep the Softener from FreezingSoftener Problem Cause Correction Salt for Water Softener Other Things to Know 4A.DIMENSIONS/SPECIFICATIONSBypass Valves Water Supply to Water SoftenerAlways Make These Initial Checks First Service TECH. Information 5A.TROUBLESHOOTINGWiring Schematic Back of Timer PWAPossible Defect Service Tech Information 5A.TROUBLESHOOTINGAutomatic Electronic Diagnostics Manual Initiated Electronics DiagnosticsSR31 shows IndicatorManual Advance Regeneration Check Servicing the Valve Service TECH. Information 5B.ROTARY Valve ServiceDisassembly AssemblyFill Cycle Service CycleBackwash Cycle Brining and Brine Rinse CyclesFast Rinse Cycle Kenmore Water Softeners Inlet ± Outlet Grounding Clamps Brine Valve AssemblyValve Assembly Bypass Installation Valve Model no Parts ListOwners Manual
Related manuals
Manual 32 pages 12.25 Kb
Top Page Image Contents