Gemini CFX-40 manual Troubleshooting, Specifications, Robo Start, Pgm

ROBO START:

IN SINGLE-AUTO CUE MODE:

Use ROBO START (29) in SINGLE-AUTO CUE MODE to alternate play between the CFX-40 two CD players (one track from one side,

then one from the other). In SINGLE-AUTO CUE MODE play starts immediately with no blank or “dead” space. ROBO START causes one side of the CD player to play when the other side is paused.

1.Engage SINGLE-AUTO CUE MODE with the SINGLE (16) button.

2.Press the ROBO START (29) button to activate ROBO START. Play will alternate between the two CD players. At the end of a track, the playing side pauses and the other CD deck plays a track. At the end of this track, the playing side pauses and the first CD deck resumes play.

IN CONTINUOUS MODE OR DURING NORMAL PLAY:

If you use ROBO START without SINGLE-AUTO CUE MODE

(in CONTINUOUS MODE or during normal play), play will not alternate automatically. Pressing pause on the playing side will cause the other side to play.

1.During normal play, set a CUE POINT on the other side of the CD player.

2.Press the ROBO START (29) button to activate ROBO START (the button will blink).

3.Press PLAY/PAUSE (11) button on the playing side to begin play from the cue point on the other side.

NOTE: PAUSING THE PLAYING SIDE IN THE MIDDLE OF A TRACK WILL CAUSE THE OTHER SIDE TO PLAY. WHEN THAT TRACK ENDS, PLAY WILL BEGIN FROM THE MIDDLE OF THE TRACK WHERE PLAY WAS PAUSED.

PGM:

PROGRAM:

First choose either DISC 1 or 2, and press STOP (8) to reset any previous program on the side that is chosen. Then press either A or B

(30)to choose DISC 1 or 2. Next press PGM (30) for PROGRAM mode, (the PGM LED will start flashing green). Select the TRACK NUMBER with the NUMBER PAD and SET (30) afterwards to select a track for that slot. Continue to press PGM (30) and select tracks, until filled with the total number of tracks. Then press PLAY/PAUSE (11) to start the program (the PGM LED will be solid green). To exit the PROGRAM press the STOP (8) button. The SINGLE (16) AUTO CUE mode that is being used, such as CONTINUOUS or SINGLE modes will affect the way the tracks play, ROBO START will not be affected by

PROGRAMING.

DIRECT SELECT:

To DIRECTLY SELECT a TRACK, just press the TRACK NUMBER then SET (30) followed by PLAY/PAUSE (11) to PLAY the last selection.

TROUBLESHOOTING:

•If the disk will not play, check to see if the disc was loaded correctly (label side up). Also check the disc for excessive dirt, scratches, etc.

•If the disc turns but there is no sound, check the cable connections. If they are okay, check your amplifier or receiver.

•If the CD skips, check the CD for dirt or scratches. Do not assume that the CD player is defective. Many CDs are recorded out of spec and will skip on most or all CD players. Before sending the unit in for repair, try playing a CD that you are sure plays properly.

SPECIFICATIONS:
GENERAL:
Type	Dual Mechanism Compact Disc Player w/wired remote
Disc Type		Standard Compact discs (12 cm & 8 cm)
Time Display		Track Elapsed, Track Remain, or Total Remain
Variable Pitch	± 4%, ± 12%, ± 24%, & ±100% Slider with Resume Switch
Pitch Bend		± 20% Maximum
Instant Start		Within 0.015 seconds
Track Selection		1 to 99 Tracks
Installation		19" Rack Mountable Player Unit, 2 U
		19" Rack Mountable Control Unit, 2 U
AUDIO SECTION:
Quantization		1 Bit Linear/Channel, 3 Beam Laser
Oversampling Rate		8 Times
Sampling Frequency		44.1 kHz
Frequency Response		20 Hz to 20 kHz
Digital Output		IEC958
Total Harmonic Distortion		Less Than 0.05%
Signal to Noise Ratio		104 dB
Dynamic Range		98 dB
Channel Separation		90 dB (1 kHz)
Output Level		1.9 Volts R.M.S.
Power Supply		AC 120/230V, 60/50 Hz
Dimensions:
Remote Control:		W 19” x H 3.5” x D 2.75” (482 x 88 x 70mm)
Main Unit:		W 19” x H 3.5” x D 10” (482 x 88 x 254mm)
Weight:
Remote Control:		4 lbs (1.8 kg)
Main Unit:		10.2 lbs (4.6 kg)
ACCESSORIES:
Remote Control Cables:		2
Stereo RCA Line Cables		2
Operating Instructions		1
Warranty Card		1
Power Cord		1

SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE WITHOUT

NOTICE FOR PURPOSE OF IMPROVEMENT.

(7)