Delta 980T-SSSD-DST Series, 980T-SS-DST Series manual Water damage

Page 9

Correct method

Método Correcto

Bonne méthode

2

3

1

4

Incorrect Installation

Instalación Incorrecta

Installation Incorrecte

Custom Fit Connections - Plastic Sleeve Installation Instructions

1.

Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier

 

installation and cut tube. Ensure cut is straight and burr free.

2.

Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown.

3.

Insert tube into outlet fitting (4). Tube should touch bottom of hole inside fitting.

4.

Slide plastic sleeve down tube until it engages top of fitting. NOTICE: Failure to use

 

plastic sleeve in the correct orientation will result in disconnection and possible

 

water damage.

Do not install sleeve upside down.

No instale la manga boca abajo.

N’installez pas le manchon à l’envers.

Ensure cut is straight.

Asegúrese que el corte esté recto.

Assurez-vous que la coupe est droite.

5. Slide nut over plastic sleeve. With wrench, tighten nut 2 turns past finger tight.

Conexiones Especiales - Instructions d’installations de le manchon en plastique

1. Identifique la longitud deseada del tubo (1). Deje 1” – 2” de soltura para una instalación más fácil y sin rebabas. Asegure que el corte sea recto y sin rebabas.

2.Resbale la tuerca (2) y la manga plástica (3) sobre el tubo cortado. Asegure la manga se orienta según lo demostrado.

3.Introduzca el tubo dentro del accesorio (4). El tubo debe tocar el fondo del agujero dentro del accesorio.

4.Deslice la manga plástica hacia abajo en el tubo hasta que encaje el la parte superior del accesorio. AVISO: El no usar la manga plástica en la orientación correcta resultará en desconexión y posible daño por agua.

5.Deslice la tuerca sobre la manga plástica. Con la llave de tuercas, apriete la tuerca dándole 2 vueltas más de si fuera apretado a mano.

Spéciaux Branchement - Instrucciones para la Instalación del la Manga Plástica

1.Identifiez la longueur désirée du tube (1). Laissez 1 à 2 pouces de la longueur supplémentaire pour faciliter l’installation et coupez le tube. Faites une coupe d’équerre et enlevez les bavures.

2.Glissez l’écrou (2) et la manchon en plastique (3) sur le tube coupé. Assurez la manchon est orienté comme montré.

3.Introduisez le tube dans le raccord (4). Le tube doit toucher le fond du trou à l’intérieur

du raccord.

4.Faites glisser le manchon en plastique dans le tube jusqu’à ce qu’il pénètre dans la partie supérieure du raccord. NOTIFICATION : Si le manchon en plastique n’a pas été installé dans l’orientation correcte, le raccord peut se défaire et l’eau peut occasionner des dommages.

5.Faites glisser l’écrou sur le manchon en plastique. Serrez-le à la main, puis faites deux tours à l’aide d’une clé.

1

2

Do not use RP51243 gasket

(1)supplied with PEX tubing or brass ferrule (2) supplied with valve stops.

No use RP51243 empaque

(1)suministrado con el tubería de PEX o el casquillo de bronce (2) suministrado con las válvulas de cierre.

N’utilisez pas RP51243 le joint (1) fournie avec la tuy- auterie de PEX ou la bague en cuivre (2) fournie avec les robinets d’arrêt.

Ensure tube is fully inserted into stop before sliding sleeve down to engage top of fitting.

Asegúrese que el tubo este completamente introducido dentro del tope antes de deslizar la manga hacia abajo para encajar la parte superior del accesorio.

Assurez-vous que le tube est introduit entièrement dans le robinet d’arrêt avant de faire glisser le manchon vers le bas pour le fixer à la partie supérieure du raccord.

9

60156      Rev. A

Image 9
Contents Inscrivez le numéro de modèle ici 980T-SS-DST & 980T-SSSD-DSTBackflow Protection System RP60446 Solenoid Assembly RP53210 Sprayer Assembly w/Integral ChecksRP50815 RP52217Installation du bec Spout Installation For Top Mount SinksSpout Installation For Under Mount Sinks Installation Du Bec Sur Un Évier À Montage Sous ComptoirInstallation de la soupape Valve Assembly InstallationSolenoid Installation Installation de l’électrovanneHose Installation Installation de FlexibleInstalación De la Manguera Wire Connections Conexiones de AlambreBranchement des fils Important Vous devez installer ces clapets de Problemas Potenciales y SolucionesConexiones Especiales Muy larga y debe recortarse para crear unaWater damage Soap Dispenser Installation Installez le distributeur de savonInstale el Dispensador de Jabón Setting The Handle Limit Stop Optional Fijando la parada de límite de la manija opcionalPlaçant l’arrêt de limite de poignée facultatif Low Battery Indication MaintenanceCleaning and Care Mantenimiento

980T-SS-DST Series, 980T-SSSD-DST Series specifications

The Delta 980T-SSSD-DST Series and the 980T-SS-DST Series are two innovative faucet collections that offer both elegance and functionality for modern kitchens and bathrooms. Designed with precision and style, these faucets stand out due to their unique technological features and superior performance.

One of the primary characteristics of the Delta 980T-SSSD-DST Series is its innovative Touch2O Technology, which allows users to turn the water on and off with just a simple touch anywhere on the faucet’s body or handle. This hands-free convenience enhances the user experience, especially when dealing with messy hands or busy cooking environments. The faucet also includes a temperature indicator that provides visual cues, ensuring that users can easily adjust the water temperature for comfort and safety.

In addition to touch technology, the Delta 980T-SSSD-DST Series is equipped with the Delta MagnaTite Docking system. This unique feature uses a powerful magnet to securely hold the spray wand in place when not in use, ensuring a sleek and tidy appearance while also enhancing durability and preventing wear over time. The wand can be pulled down with ease, providing a versatile spray that can switch between a strong flow and a comfortable spray, thanks to the integrated spray head.

The 980T-SS-DST Series focuses on providing flow efficiency while remaining environmentally friendly. With a maximum flow rate of 1.8 GPM (gallons per minute), these faucets meet WaterSense standards, which means they help conserve water without sacrificing performance. Delta's commitment to sustainability is further illustrated through their use of lead-free materials, ensuring the safety and quality of water for everyday use.

Another notable feature of the Delta 980T-SSSD-DST Series is the Touch-Clean spray holes that make maintenance effortless. A simple swipe with a finger easily removes mineral buildup from the spray head, simplifying the cleaning process and prolonging the faucet's life.

Overall, both the Delta 980T-SSSD-DST Series and the 980T-SS-DST Series exemplify modern design combined with cutting-edge technology. Their combination of user-friendly features, durability, and stylish aesthetics make them a desirable addition to any kitchen or bathroom setting, providing both functionality and a touch of elegance. These series encapsulate Delta Faucet's commitment to innovation and quality, ensuring you have the best tools at your disposal for everyday tasks.