Craftsman 113.179255 Maintenance, Filter Removal, Installation, Clean NCarry Vac Cleaning

Page 13

Maintenance

Filter

WARNING: To reduce the risk of

injury from accidental starting, unplug power cord before changing or clean- ing filter.

NOTE: This filter is made of high quality paper designed to stop very small parti- cles of dust. The filter can be used for wet or dry pick up. Handle the filter care- fully when removing to clean or installing it. Creases in the filter pleats may occur from installation but creases will not affect the performance of the filter.

Filter Removal

To remove the filter for cleaning or replacement, unscrew the filter nut from the filter cage, remove filter plate and lift off filter.

WARNING: Do not remove the filter

cage. tt is there to help prevent your fingers from getting into the blower wheel.

IMPORTANT: To reduce the risk of dam- age to the blower wheel and motor, always reinstall the filter before using the vac for dry material pickup.

Filter Cleaning

Your filter should be cleaned often to maintain peak vac performance.

Be sure to dry the filter before storing or picking up dry debris.

IMPORTANT: After cleaning, check the filter for tears or small holes. Do not use a filter with holes or tears in it. Even a small hole can cause a lot of dust to come out of your vac. Replace it immedi- ately.

Cleaning A Dry Filter

Some removal of dry debris can be accomplished without removing the filter from the vac. Slap your hand on top of the power assembly while the vac is turned off and remove from the storage rack.

For best cleaning results due to accumu- lated dust, clean the filter in an open area. Cleaning SHOULD be done out- doors and not in the living quarters.

After filter removal from vac, remove the dry debris by gently tapping the filter

against the inside wall of your dust vac canister. The debris will loosen and fall.

For thorough cleaning of dry filter with fine dust (no debris), run water through it as described under "Cleaning A Wet Filter'.

Cleaning A Wet Filter

After filter is removed, run water through the filter from a hose or spigot. Take care that water pressure from the hose is not strong enough to damage filter.

Remember: To dry a filter quickly, reinstall the filter on the vac and allow the unit to

run for approximately 10 minutes. The clean air rushing through the filter will dry it.

Installation

Refer to "Filter Assembly" Section of this

manual.

Allow the filter to dry before storing the

vac.

Clean 'NCarry Vac Cleaning

To keep your WeVDry Clean 'NCarry Vac looking its best, clean the outside with a cloth dampened with warm water and mild soap.

To clean the vac canister:

1.Dump debris out.

2.Wash vac canister thoroughly with warm water and mild soap.

3.Wipe out with dry cloth.

WARNING: To assure product SAFE- TY and RELIABILITY, repairs and adjustment should be performed by Sears Service Centers, always using Sears replacement parts,

13

Image 13
Contents Craftsmanj Important Safety Instructions Extension Cord Length ! Gauge A.W.G Introduction Unpacking and Checking Carton ContentsFilter Cage Assembly Replacement Filter AssemblyAssembling Accessory Bin to Lower Rack Storage Rack Assembly & MountingLip of Rack Accessory Assembling Upper and Lower RackMounting Storage Rack AssemblyMounting Storage Rack to Wail Vac Assembly Clean N Carry Vac AssemblyAssemblyVac Canister Lock VacMotor\ JRack Hanging Vac on StorageStorage Rack Hanging Vac on Storage Rack AccessoriesCord Storage Hose and Extension Wand StorageHoses 14 & 7 Pos-I-Lock Diffuser Cap AssemblyEmptying the Vac Canister OperationVacuuming Dry Materials Vacuuming LiquidsInstallation MaintenanceClean NCarry Vac Cleaning FilterRepa Pads Gallon Clean NCarry Wet/Dry Vac Model NumberGallon Clean NCarry Wet/Dry Vac Repair PartsModel Number MY-HOME For in-home major brand repair service

113.179255 specifications

The Craftsman 113.179255 is a versatile and robust 15-amp table saw that has garnered attention among woodworking enthusiasts and professionals alike. Known for its reliability and precision, this model is designed to handle a variety of cutting tasks, making it a go-to tool for both beginners and seasoned woodworkers.

One of the standout features of the Craftsman 113.179255 is its powerful 15-amp motor, which provides ample cutting power for even the toughest materials. This motor is designed to deliver consistent torque, ensuring that the saw runs smoothly and efficiently, whether you're ripping through thick hardwood or making finer adjustments for detailed joinery.

The saw comes equipped with a 10-inch blade, which is optimal for a wide range of cutting applications. The blade can easily be adjusted for height and angle, allowing for both vertical and beveled cuts. Additionally, the tool features a cast aluminum tabletop that measures 27 inches by 18 inches, providing a stable and spacious work surface that can accommodate large workpieces.

Safety is a top priority with the Craftsman 113.179255, and it includes several key safety features. The saw is fitted with an anti-kickback pawl that helps prevent the workpiece from being thrown back at the operator. Furthermore, the blade guard effectively covers the blade when not in use, reducing the risk of accidental contact.

The table saw also incorporates a sturdy fence system that ensures accurate and straight cuts. The fence is easy to adjust and locks firmly into place, providing consistent performance throughout your projects.

Portability is another characteristic that enhances the appeal of the Craftsman 113.179255. While it's robust and stable, the saw is designed to be relatively lightweight, making it easier to move around your workspace or transport to job sites.

In summary, the Craftsman 113.179255 table saw combines power, precision, and safety, making it an excellent choice for anyone serious about woodworking. With its reliable motor, durable construction, and thoughtful features, this table saw is built to perform at a high level while ensuring the safety and satisfaction of its users. Whether you're tackling a DIY project or undertaking professional carpentry, this tool is designed to meet your woodworking needs.