Electrolux PE 8036-M Components for Installation, Electrical Connection, USE of the Side Plates

Page 20

COMPONENTS FOR THE

INSTALLATION

The coffee machine is equipped with the following components for the installation (C):

1.2 side-plates 1mm

2.4 side-plates 2mm

3.2 telescopic runners

4.1 mains terminal block

5.1 cabinet lock tongue

6.1 cabinet locking bar

7.2 L brackets

8.2 rectangular washers

9.1 mains power cable

10.4 double stickers for fixing the plates

11.8 screws M4X16

12.12 self-threading screws

13.4 washers

ELECTRICAL CONNECTION

￿￿Fix the mains terminal block (C-

4)to the top back left corner of the cabinet (O/1).

￿￿Connect the mains cable to the terminal block ensuring correct polarity (C/4), and connect the coiled mains input cable between the appliance and the terminal block.

USE OF THE SIDE PLATES

The width of the cabinet in which the coffee machine should be inserted is determined by the thickness of the cabinet’s sides. To compensate the different possible measurement, the appliance is equipped with 6 plates, 4 are 2mm in thickness and 2 are 1mm. thick. They should be used to

20

compensate the internal width of the seat. For obtaining a width of 562/560mm see picture P/1 and P/2.

INSTALLATION WITHOUT

SUPPORT

￿￿Put the suitable plates (P/1,P/2) on the both sides of the housing, fixing them with the double- sticker strips (Q/1). Pay attention to the position of the bevel which indicates the right position of the plates.

￿￿Release the telescopic runners and extract the front section (Q/2)

￿￿Fix the telescopic runners’ bearings with the screws as shown in picture Q/3

￿￿Fix the 2 L brackets as shown in picture Q/4

￿￿Install the cabinet locking bar using the rectangular washers and the specific M4 screws as shown in picture Q/5

￿￿Install the telescopic runners on the both sides of the machine as shown in picture Q/6

￿￿Insert the machine: the telescopic runners should be coupled with the runners‘ bearings which are already fastened on the sides. (Q/7)

￿￿Check the safety lock clicks when the runners are pushed in.

￿￿Adjust the cabinet locking bar if necessary, for the correct locking position of the machine, and tighten the screws as shown in picture Q/8

￿￿Push the cabinet block button so that the machine will be well fastened (F/2).

Image 20
Contents PE 8036-M Page Page Page Page Page Page Page Page Description of the Control Panel FIG. B Description of the Coffee Machine FIG. aRecommendations OperatingFor Installation Servicing HOW to Respect EnvironmentInstructions for the First USE Fill UP the Water ReservoirFill UP the Coffee Beans Container Starting ProcessProgramming of the Ground Coffee Measure Reset of Standard ValuesRegulation of the Ground Coffee Accessories Drawer OptionalProgramming the Amount Coffee to be Dispensed Programming the Amount Water to be DispensedUSE of Coffee Pods E System CoffeeUSE of Coffee HOW to Prepare AN Excellent Espresso HOT WaterSteam Heating LiquidsHOW to Prepare Cappuccino Foam RecipesItalian Cappuccino Viennese CappuccinoCleaning and Servicing Installation Boiler Cleaning CycleInstalling the Machine Into Furniture Housing Water ReservoirComponents for Installation Installation Without SupportElectrical Connection USE of the Side PlatesWater Connection Installation with SupportWhat to do IF… Technical Specifications FusesCustomer Care Declaration of Guarantee TermsService & Spare Parts Guarantee Conditions European GuaranteePage Page Page Page Page Description of the Coffee Drawer Picture a Adjustment of the Front PanelVertical Adjustment Horizontal Adjustment Fixing the Front PanelAEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG