Dolby Laboratories DP572 user manual DP571 Setup Mode Menu Reference, 3DP571 Unit Setup menus

Page 38

Dolby E Multichannel Distribution System User Manual

DP571 Dolby E Encoder

 

 

 

 

3.2DP571 Setup Mode Menu Reference

DP571 Unit Setup

DP571 Unit Setup

DP571 Unit Setup

DP571 Unit Setup

DP571 Unit Setup

DP571 Unit Setup

Program Config

Operating Mode

Presets

Metadata Params

System Settings

Firmware Upgrade

Figure 3-3DP571 Unit Setup menus

This is the top level of the DP571 menu hierarchy for editable parameters. Each menu is discussed in its own section and displayed with all submenus and values.

Conventions

In the menu diagrams, the arrow keys select among menus at the same hierarchical level and settings within a menu category. Although selection between menus and settings is indicated in the diagrams by horizontal and vertical arrows, respectively, this is a graphical convention only. The ↓ → keys both go to the next menu or setting; the

↑← keys both return to the previous menu or setting. A double-headed arrow in the diagrams indicates that an arrow key can select between the two settings or menus.

The Esc and Enter keys ascend and descend, respectively, one menu level. They are labeled in the menu diagrams and appear as single-headed arrows; down for Enter and up for Esc.

3-6

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Dolby E Model DP571 Encoder Model DP572 DecoderUnited Kingdom Dolby Laboratories IncUnited States Table of Contents 10BASE-T DP572 Setup Mode Menu Reference Page List of Figures List of Tables Preface Regulatory Notices CanadaIEC Notices Important Safety Notice Aviso Importante De Seguridad Belangrijk Veiligheids-voorschriftChapter Introduction Unpacking and Inspection Check Main Fuse Fusing InformationUnpacking and Inspection Internal Fuse 1Checking the main fuseDigital I/O Signal CharacteristicsSystem Considerations Video ReferenceConnection with the DP569 Multichannel Encoder 2Connection between a DP569 and DP572Front-Panel User Interface Conventions3DP571 and DP572 front-panel controls and LEDs Menu Selection and Push-button Operation Display LEDs Dolby E Program ConfigDisplay Output/Input DataTC and Main Fault, Remote, PCM Dly, Error, and VRefName Function Input/Output Channel ActivityRemote Quickstart Guide for the DP571 and DP572 Dolby E 20bit Channel Configuration Common Features of the DP571 and DP572PCM Delay Channel MetadataConfiguring Jumper Settings Connector Tx Term On Rx Term OnChapter Common Dolby E Applications FilmMusic Commercial and InterstitialNews and Local Programming Live EventsPostproduction 1Typical Dolby E system in a postproduction facilityPage Chapter DP571 Dolby E Encoder Hardware Reference2DP571 front and back panel LTC Input PCM Delay InputDigital Inputs Main Out PCM Delay OutUsing the Status Port to Select Presets StatusAuxiliary Pin 7 Transition Pin 8 Transition PresetPreset Tally a Preset Tally B 11 10BASE-TDP571 Setup Mode Menu Reference 3DP571 Unit Setup menusEncoding Considerations Program ConfigNotational Conventions Program Program and Channel Explanation Config Metadata Revert Operating ModeTime Code Input 48kHz Pull Down Metadata SourceAC-3 Metadata Frame RateBit Depth Presets PresetsBitstream Mode Channel Mode Center Dwnmx Lev Enter EscEnter Metadata ParamsReversion Preset Channel ModeRF Mode Pro Dolby Srnd ModeLine Mode Pro Dialogue LevelFirmware Upgrade DP571 Status Mode MenuSystem Settings Chapter DP572 Dolby E Decoder 2DP572 front and rear panels 6 10BASE-T MainPCM Input Using the Status Port to Select Voiceover and Switched Modes Pin Direction Connection ExplanationDigital Outputs PCM Delay OutputCtrl in pin PCM Chan Config Output Routing Mode LTC OutputDP572 Setup Mode Menu Reference 3DP572 Unit Setup menuPCM Bypass Program PlayKHz Pull Down Bypass MetadataOutput Routing PCM Chan ConfigBypass Latency Headphone Prog Voiceover ModeDelay SRC Voiceover AttenPCM Delay Headphone MapDP572 Status Mode Menu DP572 Unit Setup Firmware UpgradePage Chapter System Specifications

DP571, DP572 specifications

Dolby Laboratories has long been a pioneer in audio and video technology, continuously pushing the boundaries of entertainment experiences. Among their range of innovative products, the Dolby DP572 and DP571 audio processors stand out as powerful tools for commercial cinema and installation applications. These devices are designed to enhance the overall sound experience in theaters, auditoriums, and other large venues, making them crucial for delivering high-quality audio.

The Dolby DP572 is a multi-channel audio processor that supports 7.1 surround sound configurations. It is equipped with advanced Dolby technologies, including Dolby Digital, Dolby Digital Plus, and Dolby TrueHD. This versatility allows filmmakers and sound engineers to create immersive soundscapes that bring an added layer of realism to the viewer's experience. One of the salient features of the DP572 is its advanced processing capabilities, which include automatic calibration, loudness control, and extensive equalization options, ensuring that the sound quality is optimized for any environment.

On the other hand, the Dolby DP571 is a companion processor designed primarily for applications that require flexible audio routing and management. It features the same high-quality audio processing as the DP572 but focuses more on signal management, making it ideal for venues that may need to adapt their audio setup frequently. The DP571 supports both analog and digital audio inputs and outputs, providing versatility for various sound systems. Both units feature user-friendly interfaces, making them accessible for system integrators and operators alike.

In terms of connectivity, both processors boast multiple inputs and outputs, allowing seamless integration with existing audio systems and peripherals. They also support industry-standard audio formats, making them compatible with a wide range of content sources. Signature Dolby technologies, such as dialogue enhancement and surround sound synthesis, ensure that even the most complex audio tracks are rendered with precision.

In summary, the Dolby DP572 and DP571 audio processors are essential components for any cinema or professional audio setup. Their advanced features, compatibility with multiple audio formats, and the legendary sound quality synonymous with Dolby make them invaluable tools for creating immersive audio experiences that captivate audiences. Whether used in conjunction or independently, these processors deliver the high-fidelity sound that is key to modern entertainment.
Top Page Image Contents