Dolby Laboratories DP571 user manual 2DP572 front and rear panels

Page 50

Dolby E Multichannel Distribution System User Manual	DP572 Dolby E Decoder

Remote
Activity	4	8
Channel	2 3	6 7

WARNING: Check fuse rating before applying power.

CAUTION To reduce the risk of fire replace only with same type and rating 250V slow-blow fuse

100-240 Vac 24VA 50-60Hz

FUSE T1A

WARNING: No user serviceable parts inside. Refer all service to qualified personnel.

Output

1

5

		PCMIn	Error	VRef
		Main	Fault	Remote
Config	3x2	8x1	6x1	Other
DolbyEProgram	5.1	5.1+2	5.1+2x1	4x2
InputData	16bit	20bit	24bit	PCM
Status		Setup	Esc
	Insert		Enter
	Delete			Contrast
	Remote		Shift

	20bit
	DolbyE 5.1+2

	E Decoder	DP572
	E Decoder	DP572
	Dolby	Model

	Ch7/8
	Ch5/6
	Digital	Outputs
	Ch3/4
	Ch1/2
Inc.	DolbyLaboratoriesInc. SanFranciscoandU.K. OutLTCMadeinU.S.A. S/NXXXXX		DP572 Decoder
andDolbythedoublesymbol-D trademarksareofDolbyLaboratories			Dolby
			Model
			E
	VideoRef
	MainIn
In			Dly Out
	PCM
	10BASE-T
	Metadata		Remote
	Auxiliary		Status

Figure 4-2DP572 front and rear panels

4-2

Image 50

Contents

Dolby E Model DP571 Encoder Model DP572 DecoderUnited Kingdom Dolby Laboratories IncUnited States Table of Contents 10BASE-T DP572 Setup Mode Menu Reference Page List of Figures List of Tables Preface Regulatory Notices CanadaIEC Notices Important Safety Notice Aviso Importante De Seguridad Belangrijk Veiligheids-voorschriftChapter Introduction Unpacking and Inspection Check Main Fuse Fusing InformationUnpacking and Inspection Internal Fuse 1Checking the main fuseDigital I/O Signal CharacteristicsSystem Considerations Video ReferenceConnection with the DP569 Multichannel Encoder 2Connection between a DP569 and DP572Front-Panel User Interface Conventions3DP571 and DP572 front-panel controls and LEDs Menu Selection and Push-button Operation Display LEDs Dolby E Program ConfigDisplay Output/Input DataTC and Main Fault, Remote, PCM Dly, Error, and VRefName Function Input/Output Channel ActivityRemote Quickstart Guide for the DP571 and DP572 Dolby E 20bit Channel Configuration Common Features of the DP571 and DP572PCM Delay Channel MetadataConfiguring Jumper Settings Connector Tx Term On Rx Term OnChapter Common Dolby E Applications FilmMusic Commercial and InterstitialNews and Local Programming Live EventsPostproduction 1Typical Dolby E system in a postproduction facilityPage Chapter DP571 Dolby E Encoder Hardware Reference2DP571 front and back panel LTC Input PCM Delay InputDigital Inputs Main Out PCM Delay OutUsing the Status Port to Select Presets StatusAuxiliary Pin 7 Transition Pin 8 Transition PresetPreset Tally a Preset Tally B 11 10BASE-TDP571 Setup Mode Menu Reference 3DP571 Unit Setup menusEncoding Considerations Program ConfigNotational Conventions Program Program and Channel Explanation Config Metadata Revert Operating ModeTime Code Input 48kHz Pull Down Metadata SourceAC-3 Metadata Frame RateBit Depth Presets PresetsBitstream Mode Channel Mode Center Dwnmx Lev Enter EscEnter Metadata Params Reversion Preset Channel ModeRF Mode Pro Dolby Srnd ModeLine Mode Pro Dialogue LevelFirmware Upgrade DP571 Status Mode MenuSystem Settings Chapter DP572 Dolby E Decoder 2DP572 front and rear panels 6 10BASE-T MainPCM Input Using the Status Port to Select Voiceover and Switched Modes Pin Direction Connection ExplanationDigital Outputs PCM Delay OutputCtrl in pin PCM Chan Config Output Routing Mode LTC OutputDP572 Setup Mode Menu Reference 3DP572 Unit Setup menuPCM Bypass Program PlayKHz Pull Down Bypass MetadataOutput Routing PCM Chan ConfigBypass Latency Headphone Prog Voiceover ModeDelay SRC Voiceover AttenPCM Delay Headphone MapDP572 Status Mode Menu DP572 Unit Setup Firmware UpgradePage Chapter System Specifications