Electrolux EI48HI55KS, EI36HI55KS, EI30HI55KS Remote Blower Motor, Installation into Hood Insert

Page 10

10

Blower Motor Systems Installation

 

 

Remote Blower Motor

A. Front cover

 

 

 

Installation into Hood Insert

B. Blower mounting bolts (4)

 

A D. Motor electrical plug

 

 

C. Spring clip

 

Prepare for Mounting the Remote Blower System

 

 

The remote blower system must be fastened to a se-

B C

 

cure structure of the roof, ceiling, wall, floor, or new or

 

 

existing frame construction. The 4 holes on either the

 

 

inlet (bottom) side or the outlet (top) side of the blower

 

 

must be used to mount the remote blower system to

 

 

the structure.

 

 

NOTE: The mounting hole locations must span the

 

 

studs. Additional stud framing may be required.

D

 

Plywood may be used to span open areas between

 

 

 

ceiling joists or roof rafters to aid installation. This

Install Remote Blower Motor System

 

structure must be strong enough to support the weight

NOTE: The blower motor housing can be mounted

 

of the remote blower system (50 lb [22.6 kg] min).

using 4 holes from either the inlet side or the outlet side

 

Prepare the Remote Blower System

of the blower.

 

 

Excessive Weight Hazard

Use two or more people to move and install Remote blower motor system.

Failure to do so can result in back or other injury.

1.Using two or more people, move the remote blower motor system to the mounting location.

2.Remove the 10 screws from the front cover of the remote blower motor housing and set them aside.

3.Remove the front cover of the remote blower motor housing and set it aside.

NOTE: To make the blower motor housing easier to mount, the blower motor assembly can be removed. If you do not want to remove the blower motor assem- bly, proceed to “Install Remote Blower System” in this section.

To Remove Blower Motor

1.Disconnect the motor electrical plug from the blower motor assembly.

2.Remove the screws that secure the blower motor assembly to the remote blower housing and set them aside.

3.Pull the spring clip to release the blower motor assembly. Remove the blower motor assembly from the housing and place it on a covered surface.

A

A

Inlet Side

A. Mounting holes

A

A

 

 

A

A

Outlet Side

1.Position the remote blower motor housing in its mounting location and mark the 4 mounting hole locations.

2.Drill 4 mounting pilot holes using a ³⁄16” (5 mm) drill bit.

3.Attach the remote blower motor housing to the mounting location with four 6 x 80 mm mounting screws and washers.

4.If Blower Motor is removed, reinstall the blower motor assembly and secure it with the screws

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Installation, Use & Care Guide Keep a record for quick reference Important Safety Instructions Important Safety InstructionsImportant safety Instructions Read and Save These InstructionsList of Materials List of materials- Electrical & Installation requirementsHome power supply cable Electrical RequirementsFor Mobile Home Installations Product dimensionsCabinet Dimensions Location requirementsVenting Requirements Venting RequirementsInstall the 6 mm clip nuts to the outside top Blower Motor Systems InstallationInstall Hood Insert Internal Blower MotorContinue to Prepare the Location on Installation into Hood Insert Remote Blower MotorJoints. Use furnace duct tape to seal all joints tightly Complete PreparationMake Electrical Connections for Remote Blower Motor System Prepare the Location Ground WiringMake Electrical Connections ConnectionsComplete Installation Install Hood insert into Hood CabinetPrepare Hood Insert for mounting into cabinet Complete Installation and Check Operation Make Electrical Power Supply Connection to Hood InsertHood Insert Use CleaningHood Insert Use Warranty Information USAAchever l’installation et vérifier Installation du moteur interneInstallation du moteur remote Trouver l’informationAvis de sécurité important Pour usage résidentiel uniquementLisez CES Instructions ET CONSERVEZ-LES Mode Opératoire Outils et Pièces Outils et pièces- Spécifications électriquesSpécifications électriques Dimensions du placard Exigences d’emplacementDimensions du produit Installation dans une résidence mobileExigences concernant l’évacuation Installations pour régions à climat froidExigences de Ventilation Pour un fonctionnement efficace et silencieuxInstallation des Systèmes Moteurs Installation du moteur interne a la hotte intégréeContinuer à préparer l’emplacement à la Installation du moteur remote La hotte intégréeAchever la préparation Installation de la hotte Câblage a terre Préparation de l’emplacementConnexions de Préparation InitialeInstaller le couvercle du boîtier de connexion Reconnecter la source de courant électriqueUtilisation de la hotte Achever l’installation et vérifier le fonctionnementUtilisation / Entretien de la hotte Utilisation de la hotteSurfaces externes Remplacement d’une lampe à halogèneNettoyage Filtre à graisse métalliqueInformations sur la garantie Exclusions Cette garantie ne couvre pas ce qui suitInformación del producto Aviso de seguridad importante Aviso de seguridad importantePara Reducir EL Riesgo DE Incendio Ocasionado POR Grasa Funcionamiento Lista de Materiales Lista de materiales- RequisitosEléctricos y de Instalación Nivel Pistola de silicón y TaladroRequisitos de Instalación Dimensiones del productoDimensiones del Gabinete Requisitos de InstalaciónEl diámetro del tubo debe ser uniforme Requisitos de VentilaciónRequisitos de ventilación Para instalaciones en climas FríosInstalación del motor Interno a la campana Instalación del Sistema MotorInstalación del Motor Interno en la campana Motor dualContinúe en la sección Prepare la Ubicación en la página Para retirar el Motor Instale el motor Remoto externo a la campanaPreparación para el montaje del motor Remoto Desconecte el enchufe del motor ensamble motorInstalación de la campana Complete la preparaciónPrepare la ubicación Preparación InicialPreparación del soporte de la campana Prepare la UbicaciónInstale la Campana dentro del soporte para campana Use una broca de ¹⁄8 3 mm para perforar los 4 orificiosHaga las conexiones eléctricas Complete la instalación y verifique el funcionamientoUso de la Campana LimpiezaInformación sobre la garantía Page Page LI30FA

EI30HI55KS, EI48HI55KS, EI36HI55KS specifications

The Electrolux EI36HI55KS, EI48HI55KS, and EI30HI55KS are three exceptional models from Electrolux's line of refrigerators that combine cutting-edge technology with user-friendly features, making them ideal additions to modern kitchens.

The EI36HI55KS is a standout model that offers a spacious 36-inch width and a sophisticated design. This refrigerator is equipped with TwinTech Freshness Control, ensuring both the refrigerator and freezer compartments maintain optimal humidity levels. This technology keeps fruits and vegetables fresh longer, preventing spoilage and waste. The model also features a total frost-free system, eliminating the hassle of manual defrosting while maintaining constant temperature and humidity in the fridge. With a sleek stainless-steel finish, it enhances the aesthetic appeal of any kitchen.

The EI48HI55KS model offers a larger 48-inch width, making it perfect for larger households or those who appreciate extra storage space. This unit also features the advanced TwinTech Freshness Control technology, ensuring that ingredients stay fresh while also providing a dedicated crisper drawer for fruits and vegetables. Additionally, it comes with a customizable temperature control system, allowing users to select the exact temperature for specific food items. The ice maker and water dispenser add convenience for those who enjoy chilled beverages, and the energy-efficient design ensures that it doesn’t add significantly to household energy bills.

The EI30HI55KS is a more compact model at 30 inches, making it an ideal choice for smaller kitchens without sacrificing functionality. This refrigerator also embraces the TwinTech Freshness Control system and features an attractive stainless-steel finish. The adjustable shelving system allows users to optimize their storage, while the efficient LED lighting illuminates the interior, making it easy to find ingredients. Its sleek and modern design fits seamlessly into any kitchen decor.

In summary, the Electrolux EI36HI55KS, EI48HI55KS, and EI30HI55KS refrigerators are all excellent choices for consumers seeking quality and innovation. With features such as TwinTech Freshness Control, customizable temperature settings, and energy-efficient designs, these models cater to a wide range of needs. Whether you require a spacious family-sized unit or a compact refrigerator for a smaller space, Electrolux has a solution that delivers on both performance and style.
Top Page Image Contents