Electrolux EI48HI55KS, EI36HI55KS Install Hood insert into Hood Cabinet, Complete Installation

Make Electrical Connections 13

•Check that all installation parts have been removed from the shipping carton.

4.Using 2 or more people, lift hood insert onto covered surface.

5.Remove the filters. See the “Cleaning” section on page 15.

Install Hood insert into

Hood Cabinet

The hood insert attaches to the hood cabinet using four mounting screws and washers.

NOTE: Hood cabinet must be capable of supporting 75 lb (34 kg).

Prepare Hood Insert for mounting into cabinet

1.Mark the locations for the four mounting screws on the hood cabinet as shown below.

2.Using a ¹⁄8” (3 mm) drill bit, drill the 4 holes.

	A
	B
	C
F
A. Centerline	D
	E

MOUNTING HOLE DIMENSIONS

Hood	DIM B	DIM C	DIM D	DIM E	DIM F
Insert
EI30HI55KS	51⁄2” (13.9 cm)	11” (28 cm)	125⁄32” (30.9 cm)	245⁄16” (61.8 cm)	1/8” (3mm)
EI36HI55KS	6” (15.1 cm)	101⁄8” (25.7 cm)	1415⁄16” (38 cm)	2913⁄16” (75.8 cm)	1/8” (3mm)
EI48HI55KS	6” (15.1 cm)	101⁄8” (25.7 cm)	1415⁄16” (38 cm)	2913⁄16” (75.8 cm)	1/8” (3mm)

3.Mark the cutout for the rectangular clearance hole for the upper hood insert motor housing as shown.

4.Using a jigsaw or keyhole saw, cut out the rectan- gular clearance hole for the upper hood insert housing.

Mounting

holes

A. Centerline

UPPERHOOD MOTOR HOUSINgS DIMENSIONS

Hood	DIM B	DIM C	DIM D	DIM E
Insert
EI30HI55KS	413⁄32” (11.2 cm)	133⁄16” (33.5 cm)	1113⁄32” (29 cm)	2213⁄16” (58 cm)
EI36HI55KS	413⁄32” (11.2 cm)	133⁄16” (33.5 cm)	143⁄16” (36 cm)	283⁄8” (72 cm)
EI48HI55KS	413⁄32” (11.2 cm)	133⁄16” (33.5 cm)	143⁄16” (36 cm)	283⁄8” (72 cm)

Complete Installation

1.Determine and make all necessary cuts in the wall or roof for the vent system. Install the vent system before installing the cabinet hood insert. See the “Venting Requirements” section.

2.Determine the location where the power supply cable will be run through the wall.

3.Drill a 1¹⁄4” (3.2 cm) hole at this location.

4.Pull enough power supply cable through the wall to allow for easy connection to the terminal box.

5.Remove terminal box cover and set aside.

6.Remove knockout from the top of the vent hood and install a UL listed or CSA approved ½” (1.3 cm) strain relief.

7.Place the hood insert near its mounting position and run the power supply cable through the strain relief into terminal box (enough to make connection).

8.Tighten the strain relief screws.

9.Using 2 or more people, lift the hood insert into hood cabinet.

10.Fasten the hood insert using four 5 x 45 mm screws to the hood cabinet and tighten securely.

Upper Hood

Insert Motor Housings

4 mounting screws

EXCESSIVE WEIGHT HAZARD

USE TWO OR MORE PEOPLE TO MOVE AND INSTALL HOOD INSERT.

FAILURE TO DO SO CAN RESULT IN BACK OR OTHER INJURY.