Electrolux CSG 404 Parts Required, Levelling the Appliance, Fitting the Stability Bracket

Page 37

INSTALLATION

1. PARTS REQUIRED

The loose hotplate parts and battery are packed in the polystyrene fitment on top of the hotplate.

2. LEVELLING THE APPLIANCE

If the appliance requires levelling or its height adjusting (from the hotplate to any working surface), the procedure below must be followed:

1.Adjustment to suit floor conditions or height is obtained by rotating clockwise or anticlockwise the feet, at the front and rear of the appliance.

2.A spirit level should be placed on one of the oven shelves to confirm the appliance is correctly levelled.

3.FITTING THE STABILITY BRACKET

It is recommended that if the appliance is to be installed with a flexible supply pipe, a stability bracket (SK.4729.A) is fitted and is available from your supplier (see Important Safety Requirements, Page 35). These instructions should be read in conjunction with the leaflet packed with the stability bracket.

1.Place the appliance in its intended position and level appliance.

2.Mark off 275mm from the left hand side of the appliance as shown in dimension 'A', Fig 2a. This is the centre line of the fixing bracket.

3.Draw a line 100mm from the front edge of the levelling feet (see Fig.2a) and remove appliance from its position. Mark off dimension 'B' (see Fig.2a) back from this line on the centre line of the bracket to locate the front edge of the lower bracket. Fix lower bracket (with two fixing holes) to the floor then measure the height from floor level to engagement edge on back of appliance, dimension 'C' of Fig.2b.

4.Assemble upper bracket to lower bracket so that underside of bracket is dimension 'C' +3mm above floor level.

Reposition appliance and check that top bracket engages into appliance back as shown in Fig. 2b.

487mm (B)

100mm

(A)

275mm

(C)

Fig.2a

Fig.2b

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents CSG Introduction For your safetyContents Hotplate & Grill Lighting the applianceTo turn off any burner OvenBrowned it on the high setting Prior to using the grillGrill Heat controlPreheating Cooking positionsPositioning food on the grid Grill pan is supplied with a removable handle Grill pan and handleBurner sizes HotplateFor your safety Helpful hints Heat zones OvenOven shelves Roasting Baking trays and dishesCondensation Oven cooking chart Mins. per ½kg 1lb and 25 mins 30 40 mins 15 25 minsRolls and buns 10 20 mins Food preparation slow cooking Slow cookingCover food with a tight fitting lid or tin foil Do not cook casseroles over 2.7kg 6lbThaw thoroughly before cooking Left over food should be cooled quickly and refrigeratedCleaning the brass plated handles Where Care and cleaning For your safetyHotplate Crown to body Do not try to force the crown on to the body When replacing hotplate burner partsGrill Grill and oven furnitureOven General Oven cleaning cycleCleaning The Door Glass Location Installing the applianceMake sure that a stability bracket is fitted For further details seePositioning Appliance dimensionsCurtains behind the appliance Height to hotplate 900mm 920mmBattery General information For your safetyMoving your appliance For your safety Check What is wrong and why?7 0 5 9 2 9 9 2 Service and spare partsSI G 4 0 Installation Instructions Connections DimensionsGrill HotplateProvision for Ventilation Important Safety RequirementsLocation of Appliance Levelling the Appliance Parts RequiredFitting the Stability Bracket Fitting the Battery Connecting to GASPressure Testing Checking the Hotplate Checking the GrillChecking LID SHUT-OFF Device Checking the OvenT E S T E S CSG404 Contents Check List Telephone 0870 5 Part Number311692400 Important Notice
Top Page Image Contents