Electrolux EKG6046, EKG6047 user manual If a moulded plug is fitted, Connecting to the gas supply

Page 23

The wire which is coloured blue, must be connected to the terminal which is marked with the letter N or coloured black.

The wire which is coloured brown, must be connected to the terminal, which is marked with the letter L or coloured red.

Ensure that the cable does not become trap- ped when pushing the appliance into posi- tion.

If a moulded plug is fitted.

In the event of replacing a fuse in the plug supplied a 3 amp ASTA approved fuse to B.S. 1362 must be fitted.

Note: The fuse cover must be refitted when changing the fuse.

In the event of losing the fuse cover the plug must not be used until a replacement fuse cover has been obtained and fitted.

Connecting to the gas supply

This appliance is designed to be installed with an appliance flexible connection only. Supply piping should not be less than R3/8. Connection is made to the Rc ½ (½” B.S.P.) female threaded entry pipe located just be- low the hotplate level on the rear left hand side of the appliance.

NOTE: ONLY LIQUID SEALANTS TO BE USED WHEN INLET GAS PIPE IS FITTED I.E.: DO NOT USE P.T.F.E.

SEALANT TAPE.

electrolux 23

Carry out a gas tightness test after connect- ing to the gas supply.

The gas bayonet connector must be fitted in the shaded area indicated.

Take into account that it must be possible to pull the appliance forward sufficiently. Ensure the hose does not become trapped when pushing the appliance into position.

IMPORTANT: FLEXIBLE TUBING USED MUST COMPLY WITH BS.669 CURRENT EDITION.

LPG Flexible connections must be a type suitable for

L.P.G and capable of operation up to 50 mbar and carry a red stripe, band or label.

Fitting the stability chain

It is recommended that if the appliance is to be installed with a flexible supply pipe, a sta- bility chain be fitted and is available from your supplier (see Important Safety Require- ments).

These instructions should be read in con- junction with any leaflet packed with the sta- bility chain.

1.Place the appliance in its intended posi- tion and level appliance.

2.Mark a position 100mm from the top of the rear right hand corner.

Page 22 Page 24
Image 23
Page 22 Page 24
Contents EKG6046 EKG6047 CookerSafety information Electrolux. Thinking of you ContentsCare and cleaning Grill and oven furniture Product descriptionControl panel ApplianceBefore first use Operation Things to note To set the timer to switch off onlyTo cancel an automatic programme To return the appliance to manualGrill Using the grillTo light the hob burners To turn off any burnerTo remove the handle Using the top ovenGrill pan handle To attach the handleMain oven conventional cooking Heat zones Using main oven conventional cookingTo fit the top oven shelf Food preparation Slow cook Joints of meat and poultry Using slow cookMain oven shelves Slow CookHelpful hints and tips Cooking tables Grilling chartTop oven cooking chart Hours Main oven cooking chartFood Shelf position Gas mark Food Shelf position Gas mark Cleaning the outside of the appliance Care and cleaningRoasting chart Cleaning materialsCleaning the grill Removing and replacing the wire work runnersCleaning the gas hob When replacing hob burner partsCleaning between the outer and inner door glass Cleaning inside the grill and oven compartmentsCleaning the doors To replace the inner door glass ProblemPossible solution What to do if…Problem Possible solution Installation instructions If the fitted plug is removed Connecting to the electricity supplyLevelling the appliance Fitting the stability chain Connecting to the gas supplyIf a moulded plug is fitted LPG Flexible connections must be a type suitable forChecking the grill Pressure testingChecking the hob Checking the lid shut-off deviceTechnical data Environment concerns GB IE Guarantee/Customer ServiceTraining purposes Customer CareTel +353 01 4090751, Email serv- ice.eid@electrolux.ie 349171300-G-072009
Top Page Image Contents