Breville ESP6/8 manual Trouble Shooting Chart, Cleaning the Drip Tray, Decalcifying

CARE AND CLEANING cont’d

TROUBLE SHOOTING CHART

CLEANING THE DRIP TRAY

•The drip tray should be removed, emptied and cleaned at regular intervals, particularly when the water level indicator is exposed indicating the drip tray is full.

•Remove the grid, steam baffle and water level indicator from the drip tray, wash all 4 parts with water and non-abrasive washing liquid before rinsing and drying.

Do not place any of the

components in the

dishwasher.

DECALCIFYING

After regular use, hard water can cause limestone build up in and on many of the inner functioning components, reducing the brewing flow, power of the machine, and affecting the quality of coffee.

We advise decalcifying the machine on a regular basis (every 2-3 months) using a liquid decalcifying agent. Follow the instructions provided, or use the following as a guide: Diluted solution (for softer water)

•1 part decalcifying agent

•2 parts cold tap water

Concentrated solution (for harder water)

•1 part decalcifying agent

•1 part cold tap water

THE WATER TANK SHOULD

NEVER BE REMOVED OR

COMPLETELY EMPTIED

12DURING DECALCIFYING.

DECALCIFYING THE MACHINE

•Make sure the selector control is in the ‘OFF’ position and that the plug is disconnected from the power outlet.

•Remove the filter holder and pour in the decalcifying solution into the water tank.

•Plug the machine into the power outlet and turn on.

•Set power switch to the ‘ON’ position and the selector control to the ‘OFF’ position

•Place a large container under both the water outlet and the steam wand.

•As soon as the brewing temperature is reached the orange ‘temperature’ light will switch off. Set the selector control to the ‘ESPRESSO’ position and let half the decalcifying solution run through the brewing head.

•Turn the selector control to the ‘STEAM’ position and let the remaining solution run through the steam wand. When the solution has run through, set the selector control back to the ‘OFF’ position.

•After decalcifying, rinse the water tank thoroughly and re-fill with fresh cold water. To rinse the machine, run half the water through the brewing head and half through the steam wand.

•The machine is ready for use.

• The stainless steel filters should not come in contact with any decalcifying agents

•Do not use powdered decalcifying agents

PROBLEM	POSSIBLE CAUSES
Coffee does not run through	*	Machine is not turned on or plugged in
	*	Water tank is empty
	*	Selector control not in ‘Espresso’ position
	*	Coffee grind is too fine
	*	Too much coffee in the filter
	*	The filter is blocked (see Care and Cleaning)
Coffee runs out too quickly	*	Coffee grind is too coarse.
	*	Not enough coffee in the filter
Coffee runs too slowly	*	The water tank is empty or low
	*	Coffee grind is too fine
	*	Machine is blocked by scale build up
		(see Care and Cleaning)
Coffee runs out around the	*	Filter holder is not inserted in the brew head properly
edge of the filter holder	*	There are coffee grounds around the filter rim
	*	Too much coffee in the filter
	*	Coffee has been tamped too tightly
The machine is too loud	*	Water tank is empty
	*	Water tank is not securely in place
Coffee is too weak or watery	*	Coffee grind is not fine enough
		(use coffee ground for espresso machines)
Coffee is too cold	*	Machine not preheated
	*	Cups not preheated
	*	Milk not heated enough (if making a cappuccino or latte)
No crema	*	Coffee is not tamped (pressed) firmly enough
	*	Coffee grind is too coarse
	*	Coffee is not fresh
No steam is generated	*	Machine is not turned on
	*	Water tank is empty
	*	Selector control not in ‘Steam’ position
	*	Steam wand is blocked (see Care and Cleaning)
Milk is not foamy after frothing	* Not enough steam
	*	Milk is not fresh and cold

13