KitchenAid 2320680B manual Move Refrigerator to Final Location, Level and Align Refrigerator

Page 23

Move Refrigerator to Final Location

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT: To avoid floor damage, make sure levelers are raised (not touching floor) and refrigerator is on rollers before moving.

1.Place top of cardboard carton or plywood under refrigerator. Remove dolly.

2.Do not remove protective film or cover.

3.Move the refrigerator straight back and evenly into the opening. Be sure that the refrigerator side trims are not interfering with the door opening. Also, be sure that the water tubing is not kinked and the power supply cord is on top of the refrigerator.

Level and Align Refrigerator

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT: All four leveling legs must contact the floor to support and stabilize the full weight of refrigerator. Rollers are for moving refrigerator and not for permanent support.

After moving the refrigerator to its final location:

1.Use a ⁵⁄₁₆" socket driver to turn the leveling bolts clockwise to extend the legs to the floor as shown. The rollers should be off the floor.

A B

A

B

A. Rear leveling bolt

B. Front leveling bolt

2.Adjust the leveling legs to level and align the refrigerator from left to right and front to back so that the refrigerator is level and aligned with the cabinetry. The cabinetry surface must be plumb for the ideal fit of the refrigerator side trim.

3.Continue adjusting all of the leveling legs to raise the refrigerator until the top is within at least 1" (2.54 cm) of the top soffit.

NOTE: If an anti-tip board has been used, adjust the leveling legs until the top of the refrigerator is within ¹⁄₄" (6.35 mm) of the bottom of the anti-tip board as shown. Do not crush the compressor cover.

A B

C

¹⁄₄" (6 mm) max.

2" (5 cm)

D

A. Center board ¹⁄₄" (6.35 mm) max. above refrigerator

B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards

C. Attach to studs with six #8 x 3" (7.6 cm) screws

D. Compressor cover

IMPORTANT: Adjust in small increments to keep from damaging the cabinet trim and causing problems with the door alignment or top grille fit. To avoid damage to the cabinet or leveling legs, do not apply more than 50 inch- pounds (5.65 Nm) of torque to the leveling bolts. The leveling legs can be extended to a maximum of 1¹⁄₄" (3.18 cm) below the rollers.

4.For Classic and Overlay models, additional adjustments may be needed after the custom panels are installed.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents BOTTOM-MOUNT BUILT-IN Refrigerator Table of Contents/Índice/Table des matièresTable DES Matières Table of ContentsÍndice Your safety and the safety of others are very important Refrigerator SafetyOverlay Series 36 91.4 cm Models ModelsArchitect Series 36 91.4 cm Models Classic Series 36 91.4 cm ModelsLocation Requirements Installation RequirementsOpening Dimensions Tools and Parts36 35¹⁄₂ 90.2 cm 42 41¹⁄₂ 105.4 cm Electrical RequirementsRecommended Grounding Method Model Width a as shown aboveReverse Osmosis Water Supply Water Supply RequirementsTipping Radius Water PressureFront View Product DimensionsSide View 42 106.7 cm ModelsDoor Swing Dimensions Spacer Panel HingeCabinetry Panel 90˚ Door Stop Position HingeOverlay Panel OverlayPanel Custom Backer Panels 36 91.4 cm Models Custom Overlay Panel DimensionsOverlay Series Custom Panels Custom Overlay Panels 36 91.4 cm ModelsSpacer Panels All models Piece Grille Overlay Panel ConfigurationPiece Door Overlay Panel Configuration Piece Overlay Panel ConfigurationClassic Series Custom Panels 36 91.4 cm Models Classic, Architect, and Overlay SeriesDoor Panel Routing Requirements Refrigerator and Side Trim DimensionsClassic and Architect Series Custom Side Panels Top Grille Panel Routing RequirementsOverlay Series Custom Side Panels Side Trim 42 106.7 cm Models Side Trim 36 91.4 cm Models Inset Installation DimensionsRecessed Inset Installation Dimensions 36 91.4 cm Models Refrigerator 42 106.7 cm ModelsMove the Refrigerator into House Installation InstructionsUnpack the Refrigerator Reduce Tipping RadiusStyle 1 Shutoff Valve Connection Install Anti-Tip BoardsTo Install Anti-tip Boards Connect the Water SupplyPlug in Refrigerator Style 2 Copper Line Connection Connecting to Water LineConnecting to Refrigerator Level and Align Refrigerator Move Refrigerator to Final LocationDoor Panel Installation Install Overlay and Classic Series Custom PanelsDoor Alignment 36 91.4 cm Models Adjust DoorsDoor Height Adjustment 42 106.7 cm Models Door stop is located on the top hinge Door Swing Adjustment 36 91.4 cm Models110 Install Side PanelInstall Base Grille Water System Preparation Complete InstallationSu seguridad y la seguridad de los demás es muy importante Seguridad DEL RefrigeradorSerie Overlay modelos de 36 91,4 cm ModelosSerie Architect modelos de 36 91,4 cm Serie Classic modelos de 36 91,4 cmSerie Overlay modelos de 42 106,7 cm Requisitos DE InstalaciónPiezas y herramientas Requisitos de ubicación35 ¹⁄₂ 90,2 cm Medidas de la aberturaPueda ser retirada Modelo Anchura a como se muestra anteriormentePresión del agua Requisitos eléctricosRequisitos del suministro de agua Método de conexión a tierra recomendadoMedidas del producto Arco de vuelcoMedidas de oscilación de la puerta Panel espaciador Gabinetes BisagraRecubierto Puerta Recubierto Panel espaciador Posición de retención de la puerta de 90˚ Bisagra PuertaSoporte Paneles a la medida de la Serie Overlay Dimensiones del panel recubierto a la medidaVista lateral Configuración del panel recubierto con puerta de 1 piezaPaneles espaciadores todos los modelos Vista superiorPaneles del refrigerador y del congelador Juegos de paneles para puertas de fábricaJuegos de extensión de agarraderas de la puerta Panel de la rejilla superiorPanel de la puerta Vista lateral Requisitos de contorneado del panel de la rejilla superiorRequisitos de contorneado de los paneles de la puerta Medidas del refrigerador y del adorno lateralPaneles laterales a la medida para la Serie Overlay Refrigerador modelos de 42 106,7 cm Cómo hacer entrar el refrigerador en la casa Instrucciones DE InstalaciónDesempaque el refrigerador Cómo reducir el arco de vuelcoCómo instalar los tableros antivuelco Cómo instalar los tableros antivuelcoConexión del suministro de agua Modelos de 36 91,4 cm Modelos de 42 106,7 cmAbra la válvula de cierre Conexión al refrigeradorNivelación y alineamiento del refrigerador Cómo enchufar el refrigeradorCómo mover el refrigerador a su Ubicación final Vuelva a colocar los adornos y los postes esquineros Series Overlay y ClassicInstalación del panel de la puerta Cómo ajustar la altura de la puerta modelos de 42 106,7 cm Cómo ajustar las puertasAlineamiento de la puerta modelos de 36 91,4 cm El retén de la puerta está ubicado en la bisagra superior Cómo instalar la rejilla de la base Cómo instalar el panel lateralPreparación del sistema de agua Cómo terminar la instalaciónVotre sécurité et celle des autres est très importante Sécurité DU RéfrigérateurSérie Overlay modèles de 36 91,4 cm ModèlesSérie Architect modèles de 36 91,4 cm Série Classic modèles de 36 91,4 cmSérie Overlay modèles de 42 106,7 cm Exigences ’INSTALLATIONExigences d’emplacement Outillage et piècesModèle Largeur a tel quillustré ci-dessus Dimensions de l’ouvertureSi des planches antibasculement sont nécessaires, elles Puisse être enlevéePression de leau Méthode recommandée de mise à la terreSpécifications électriques Spécifications de l’alimentation en eauRayon de basculement Dimensions du produitDimensions pour le pivotement des portes Séparation Charnière PlacardDe séparation Charnière PortePanneau Porte Panneau de séparation ’appuiPanneaux personnalisés de la série Overlay Panneaux personnalisés DimensionsVue latérale Configuration pour panneau Overlay monopiècePanneaux de séparation Tous modèles Vue de dessusEnsembles de panneaux dorigine de la Poignée standard Vue supérieure Degrés. Voir Dimensions pour le pivotement des portesExigences dusinage des panneaux de porte Panneaux latéraux personnalisés de la Série Overlay Garnitures latérales modèles de 42 106,7 cm Dimensions pour un panneau inséré Modèles de 36 91,4 cmFaire entrer le réfrigérateur dans le domicile Instructions D’INSTALLATIONDéballage du réfrigérateur Réduction du rayon de basculementModèles de 36 91,4 cm Modèles de 42 106,7 cm Installation de planches antibasculementInstallation des planches antibasculement Raccordement à la canalisation deauOuvrir le robinet darrêt Raccordement au réfrigérateurEnfiler lécrou fourni sur le robinet darrêt tel quillustré Réglage de laplomb et alignement du Réfrigérateur Déplacementdu réfrigérateur à Lemplacement finalBrancher le réfrigérateur Installation des panneaux de porte Réglage de la hauteur de la porte modèles de 42 106,7 cm Ajustement de la des portesAlignement des portes modèles de 36 91,4 cm La butée de porte est située sur la charnière supérieure Installation de la grille de la base Installation du panneau latéral2320680B Achever l’installationPréparation du système d’eau Veuillez lire avant d’utiliser le système d’eau

2320680B specifications

The KitchenAid 2320680B is an innovative and versatile kitchen appliance designed to enhance culinary experiences in both home and professional kitchens. At the core of its design is a powerful motor, allowing for efficient mixing, kneading, and whipping, making it an essential tool for any cooking enthusiast.

One of the standout features of the KitchenAid 2320680B is its unique planetary mixing action. This technology ensures that the mixing attachments move in a circular motion, covering every part of the bowl while also spinning on their own axis. This results in thorough ingredient incorporation, reducing mixing time and ensuring uniform consistency for all recipes. The appliance is equipped with multiple speed settings, offering users the flexibility to adjust the speed according to their recipe requirements, whether it’s a gentle fold for delicate batters or a vigorous whip for fluffy meringues.

The KitchenAid 2320680B includes a range of attachments that expand its functionality, making it suitable for various tasks. The standard attachments typically include a flat beater, dough hook, and wire whip, allowing users to tackle a wide array of culinary tasks. For those seeking even more versatility, the appliance is compatible with a vast array of optional attachments, such as pasta makers, food grinders, and spiralizers, turning it into a multifunctional kitchen hub.

Furthermore, the design of the KitchenAid 2320680B prioritizes durability and usability. The body is constructed from high-quality materials, ensuring longevity even with frequent use. The user-friendly interface and tilting head mechanism make it easy to add ingredients, change attachments, and access the bowl, enhancing the overall cooking experience.

With its sleek, timeless aesthetic, the KitchenAid 2320680B not only performs excellently but also adds a touch of style to any kitchen décor. Available in a variety of colors, it allows users to select a model that best fits their personal taste and kitchen design.

In summary, the KitchenAid 2320680B is a powerful, versatile, and stylish addition to any kitchen. Its advanced mixing technology, array of attachments, and durable construction make it an invaluable tool for home cooks and professional chefs alike, ensuring effortless preparation of everything from simple batters to gourmet meals.
Top Page Image Contents