KitchenAid W10189719A Product Dimensions, Electrical Requirements, Installation Dimensions

Page 3

Installation Dimensions

NOTE: The grounded 3 prong outlet must be inside the upper cabinet. See “Electrical Requirements” section.

AB

36"

 

(91.4 cm)

 

min.

 

33" (83.2 cm)

12" (30.5 cm) min.

typical*

13" (33.0 cm) max.

 

69" (175.3 cm) min.

 

A. 2" x 4" wall stud

B. Grounded 3 prong outlet

*33" (83.2 cm) is typical for 69" (175.3 cm) installation height. Exact dimension may vary depending on type of range/cooktop below.

Product Dimensions

 

"

 

 

18

¹⁄₄

35

⁷⁄₈"

.4 cm)

 

(91.1 cm)

(46

 

 

 

18 ¹⁄₄"

 

 

15 ¹⁄₂"

 

 

(39.4 cm)

(46.4 cm)

 

 

 

 

 

Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Observe all governing codes and ordinances.

Required:

A 120 Volt, 60 Hz, AC only, 15- or 20-amp electrical supply with a fuse or circuit breaker.

Recommended:

A time-delay fuse or time-delay circuit breaker.

A separate circuit serving only this microwave oven.

GROUNDING INSTRUCTIONS

For all cord connected appliances:

The microwave oven must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. The microwave oven is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

WARNING: Improper use of the grounding plug can result in a risk of electric shock. Consult a qualified electrician or serviceman if the grounding instructions are not completely understood, or if doubt exists as to whether the microwave oven is properly grounded.

Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the microwave oven.

SAVE THESE INSTRUCTIONS

3

Image 3
Contents Microwave Hood Combination Safety Microwave Hood Combination Installation InstructionsInstallation Requirements Tools and PartsLocation Requirements Required Product DimensionsInstallation Dimensions Electrical RequirementsConvert Microwave Oven to External Venting Installation InstructionsTo Install Vent Deflector Remove Mounting PlateC D Locate Wall Studs Possible Wall Stud ConfigurationsDrill Holes in Rear Wall Mark Rear WallWall Stud at One Corner Hole Figure Attach Mounting Plate to WallPrepare Upper Cabinet No Wall Studs at Corner Holes Figures 1For Roof Venting Installation Only Install the Microwave OvenComplete Installation Recommended Standard Fittings Venting Design SpecificationsFor optimal venting installation, we recommend Rectangular to Round Transition¹⁄₄ x 10 8.3 x 25.4 cm vent system = 73 ft 22.2 m total Replacement PartsAssistance Recommended Vent Length

W10189719A, W10190015A specifications

KitchenAid has long been synonymous with quality and innovation in kitchen appliances, and the W10190015A and W10189719A models are no exception. These products exemplify the brand's commitment to delivering exceptional performance and user-friendly features, making them essential tools for both amateur and professional chefs.

The W10190015A is primarily known as a replacement part for certain KitchenAid appliances, including various models of dishwashers. This component focuses on ensuring optimal performance and longevity of the appliance, featuring robust design characteristics that meet high standards of durability. Its compatibility with a wide range of KitchenAid dishwasher models means that users can easily find a suitable replacement without worrying about fitment issues. The installation process is designed to be straightforward, empowering DIY enthusiasts to tackle repairs without the need for professional assistance.

Conversely, the W10189719A is often noted for its role in enhancing the functionality of KitchenAid refrigerators. This part typically focuses on water filtration, ensuring that the water dispensed from the refrigerator is clean and free from impurities. With a high filtration capacity, it efficiently removes contaminants, providing peace of mind for families who rely on their refrigerator for both drinking water and ice-making capabilities. The W10189719A is designed for easy replacement, ensuring that users can maintain their refrigerator's performance without hassle.

Both products benefit from KitchenAid's commitment to quality engineering, ensuring that they not only perform well but also stand the test of time. The brand's adherence to rigorous testing standards means that users can trust these components to deliver consistent results, whether in terms of cleaning performance in dishwashers or water quality in refrigerators.

In addition to their practical features, these models reflect KitchenAid’s aesthetic sensibilities, blending seamlessly into the modern kitchen environment. The sleek design and attention to detail serve to complement the overall elegance of KitchenAid appliances, making them not only functional but also visually appealing.

In summary, the KitchenAid W10190015A and W10189719A are exemplary parts that embody the brand's dedication to quality, performance, and user satisfaction. Whether it's ensuring your dishwasher runs efficiently or providing purified water from your refrigerator, these components are integral to maintaining the high standards that KitchenAid has set in the kitchen appliance market.