KitchenAid 2313715A manual Drain Connection, Gravity Drain System, Rear View, Side View

Page 5

4.Fasten shutoff valve to cold water pipe with pipe clamp. Be sure outlet end is solidly in the ¹⁄₄" (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws carefully and evenly so washer makes a watertight seal. Do not overtighten the pipe clamp or you may crush cold water pipe if it is soft copper tubing. Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle-type valve which reduces water flow and clogs more easily.

5.Now you are ready to connect the copper tubing. Use ¹⁄₄" (6.35 mm) OD soft copper tubing for the cold water supply.

■Ensure that you have the proper length needed for the job. Be sure both ends of the copper tubing are cut square.

■Slip compression sleeve and compression nut on copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

A

H B

C

NOTE: To avoid rattling, be sure the copper tubing does not touch the cabinet’s side wall or other parts inside the cabinet.

A

B

C

D

E F

G

A. Line to ice maker

 

E. Ferrule

 

 

B. Nut (purchased)

 

F. Nut

 

 

C. Ferrule (purchased)

 

G. Supplied line from ice maker

D. Coupling (purchased)

 

 

 

9.Turn shutoff valve ON.

10.Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

Drain Connection

Gravity Drain System

G F E

D

Connect the ice maker drain to your drain in accordance with all state and local codes and ordinances. If the ice maker is provided with a gravity drain system, follow these guidelines when installing drain lines. This will help keep water from flowing

A. Cold water pipe

E. Compression nut

B. Pipe clamp

F. Compression sleeve

C. Copper tubing

G. Shutoff valve

D. Coupling (purchased)

H. Packing nut

6.Place the free end of the tubing into a container or sink, and turn on main water supply and flush out tubing until water is clear. Turn off shutoff valve on the water pipe.

NOTE: Always drain the water line before making the final connection to the inlet of the water valve to avoid possible water valve malfunction.

7.Bend the copper tubing to meet the water line inlet which is located on the back of the ice maker cabinet as shown. Leave a coil of copper tubing to allow the ice maker to be pulled out of the cabinet or away from the wall for service.

REAR VIEW

A

B

C

A. Drain hose (drain pump models only)

B. Vent hose (drain pump models only)

C. Water supply line

8.Thread the nut onto the coupling on the end of the copper tubing. Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

back into the ice maker storage bin and potentially flowing onto the floor causing water damage.

■Drain lines must have a minimum of ⁵⁄₈" (15.88 mm) inside diameter.

■Drain lines must have a 1" drop per 48" (2.54 cm drop per 122 cm) of run or ¹⁄₄" drop per 12" (6.35 mm per 30.48 cm) of run and must not have low points where water can settle.

■The floor drains must be large enough to accommodate drainage from all drains.

■The ideal installation has a standpipe with a 1¹⁄₂" (3.81 cm) to 2" (5.08 cm) PVC drain reducer installed directly below the outlet of the drain tube as shown. You must maintain a

1" (2.54 cm) air gap between the drain hose and the standpipe.

■It may be desirable to insulate the drain line thoroughly up to the drain inlet.

SIDE VIEW

 

A

1⁷⁄₈"

B

 

(1.9 cm)

 

 

1" (2.5 cm)

20" (50.80 cm)

C

2" - 1¹⁄₂"

 

 

(5 cm - 3.8 cm)

D

A. Drain hose

B. 1" (2.54 cm) air gap C. PVC drain reducer

D. Center of drain should be 20" (50.80 cm) from front of door, with or without the ³⁄₄" (1.91 cm) panel on the door. The drain should also be centered from left to right (8¹³⁄₁₆" from either side of the ice maker).

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents ICE Maker Table of Contents/Table des matièresTable of Contents ICE Maker SafetyUnpack the Ice Maker Installation InstructionsLocation Requirements Electrical RequirementsConnect Water Supply Water Supply RequirementsLeveling Gravity Drain System Drain ConnectionRear View Side ViewHow Your Ice Maker Works ICE Maker USENormal Sounds ICE Maker Care CleaningUsingthe Controls Dirty or clogged condenser CondenserInterior Components To shut down the ice maker Vacation and MovingCareIce Production TroubleshootingIce Maker Operation Plumbing Problems Assistance or ServiceIce Quality U.S.AONE Year Limited Warranty Kitchenaid ICE Maker WarrantyCanada Items Kitchenaid will not PAY forSécurité DE LA Machine À Glaçons Instructions D’INSTALLATIONDéballage de la machine à glaçons Enlèvement des matériaux d’emballageMéthode de mise à la terre recommandée Emplacement d’installationSpécificationsélectriques Spécifications de l’alimentation en eauRaccordement à lacanalisation d’eau NivellementOutillage nécessaire Outils requisVidange par gravité Raccordementau conduit dévacuationOuvrir le robinet darrêt VUE ArrièreSystème à pompe de vidange sur certains modèles Sons normauxRaccordement du conduit dévacuation VUE LatéraleHoliday Mode mode vacances Utilisation des commandesUtilisation DE LA Machine À Glaçons Fonctionnement dela machine à glaçonsNettoyage Entretien DE LA Machine À GlaçonsComposants intérieurs Machine à glaçons avec pompe de drainage DéménagementProduction deglaçons DépannageLa machine à glaçons ne fonctionne pas La machine à glaçons semble bruyanteProblèmes deplomberie Assistance OU ServiceQualité des glaçons Garantie Limitée DE UN AN Garantie DE LA Machine À Glaçons KitchenaidKitchenaid NE Prendra PAS EN Charge 2313715A

2313715A specifications

The KitchenAid 2313715A is a versatile and innovative kitchen gadget designed for home cooks who are looking to enhance their culinary experience. This food processor has become a staple in many kitchens due to its powerful performance and user-friendly design.

One of the standout features of the KitchenAid 2313715A is its powerful motor, which allows for efficient and quick processing of ingredients. This motor is designed to handle a variety of tasks, from chopping and slicing to mixing and pureeing. With multiple speed settings, users can easily adjust the power to suit their specific needs, ensuring that food is prepared to perfection.

In addition to its impressive motor, the KitchenAid 2313715A boasts a generous bowl capacity, allowing users to process larger quantities of food at once. This is particularly beneficial when preparing meals for families or gatherings, as it reduces the time spent on food prep. The bowl is also designed with a wide feed chute that accommodates whole fruits and vegetables, minimizing the need for pre-cutting and maximizing efficiency.

The design of the KitchenAid 2313715A is not only functional but also aesthetically pleasing. The sleek and modern appearance makes it an attractive addition to any kitchen countertop. Furthermore, the appliance is equipped with a variety of attachments, including slicing discs, shredding discs, and a metal blade, which provide users with added versatility for multiple culinary tasks.

Additionally, the KitchenAid 2313715A features a safety locking mechanism, ensuring that the processor operates only when securely assembled. This safety feature lends peace of mind, particularly for those who may be new to using kitchen appliances.

Maintenance and cleaning are also a breeze with this food processor. Most components are dishwasher-safe, making it easy to keep the appliance in optimal condition after use.

Overall, the KitchenAid 2313715A food processor stands out for its robust performance, user-friendly design, and aesthetic appeal. It incorporates cutting-edge technology while maintaining the reliability that KitchenAid is known for, making it an essential tool for both aspiring and experienced chefs alike. Whether you’re preparing everyday meals or exploring new recipes, the KitchenAid 2313715A is designed to elevate your cooking experience.
Top Page Image Contents