KitchenAid 2313715A manual Vacation and MovingCare, To shut down the ice maker

Page 9

9.Remove the two thumb screws that hold the water pan in place. Push down with one hand on the front of the pan while pulling forward on the bottom back side.

 

A

B

B

 

C

 

D

A. Water pan

B. Water pan thumb screws

C. Water pan drain pump

D. Drain cap

10.Remove, clean and replace the ice scoop and ice scoop holder.

■After removing the ice scoop, remove the holder by lifting the front free from the cutter grid cover. Then lift the back of the holder slightly to release the rear hook and pull forward.

■Wash the ice scoop holder along with the other interior components using the following instructions.

■Replace the ice scoop holder by aligning the rear hook with the opening (the holder angles down slightly). Slide the holder back fully until the front rests securely on the cutter grid cover.

A

A. Ice scoop holder

11.Wash the interior components (cutter grid, exterior of hoses, and water pan) and the storage bin, door gasket, ice scoop, and ice scoop holder with mild soap or detergent and warm water. Rinse in clean water. Then clean the same parts with a solution of 1 tbs (15 mL) of household bleach in 1 gal. (3.8 L) warm water. Rinse again thoroughly in clean water.

NOTE: Do not remove hoses. Do not wash plastic parts in dishwasher. They cannot withstand temperatures above 145°F (63°C).

12.Replace water pan by pushing back on the bottom with one hand while pushing up and back on the top. Secure the water pan by replacing both screws.

13.Replace the water pan drain pump by aligning the slots in the water pan to the tabs in the pump. Push the pump and the water pan together, then rotate the pump one-quarter turn.

14.Check the following:

■Drain cap from the water pan is securely in place. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

■Hose from water pan is inserted into storage bin drain opening.

■Be sure that the water pan drain pump is fully inserted into the water pan. If the pump is loose, water will empty from the water pan and cause poor or no ice production.

15.Slide the cutter grid back into place and secure it by replacing the right-hand screw and plastic spacer. Then tighten the left-hand screw. Reconnect the cutter grid harness and the ice level sensor harness.

16.Replace the cutter grid cover.

17.Plug in ice maker or reconnect power.

Vacation and MovingCare

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

To shut down the ice maker:

1.Unplug ice maker or disconnect power.

2.Remove all ice from storage bin.

3.Shut off the water supply.

4.Remove the two screws in the lower access panel and the two screws from the base grille area of the front panel support. Pull forward to remove the lower access panel.

A

A

B

B

A. Lower Access Panel Screws

B. Base Grille Screws

5.Disconnect the inlet and outlet lines to water valve. Allow these lines to drain and then reconnect to the valve.

6.Replace lower access panel and screws.

7.Drain water from water pan by removing the drain cap.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents ICE Maker Table of Contents/Table des matièresTable of Contents ICE Maker SafetyUnpack the Ice Maker Installation InstructionsLocation Requirements Electrical RequirementsWater Supply Requirements LevelingConnect Water Supply Gravity Drain System Drain ConnectionRear View Side ViewICE Maker USE Normal SoundsHow Your Ice Maker Works Cleaning Usingthe ControlsICE Maker Care Condenser Interior ComponentsDirty or clogged condenser To shut down the ice maker Vacation and MovingCareTroubleshooting Ice Maker OperationIce Production Plumbing Problems Assistance or ServiceIce Quality U.S.AONE Year Limited Warranty Kitchenaid ICE Maker WarrantyCanada Items Kitchenaid will not PAY forSécurité DE LA Machine À Glaçons Instructions D’INSTALLATIONDéballage de la machine à glaçons Enlèvement des matériaux d’emballageMéthode de mise à la terre recommandée Emplacement d’installationSpécificationsélectriques Spécifications de l’alimentation en eauRaccordement à lacanalisation d’eau NivellementOutillage nécessaire Outils requisVidange par gravité Raccordementau conduit dévacuationOuvrir le robinet darrêt VUE ArrièreSystème à pompe de vidange sur certains modèles Sons normauxRaccordement du conduit dévacuation VUE LatéraleHoliday Mode mode vacances Utilisation des commandesUtilisation DE LA Machine À Glaçons Fonctionnement dela machine à glaçonsNettoyage Entretien DE LA Machine À GlaçonsComposants intérieurs Machine à glaçons avec pompe de drainage DéménagementProduction deglaçons DépannageLa machine à glaçons ne fonctionne pas La machine à glaçons semble bruyanteAssistance OU Service Qualité des glaçonsProblèmes deplomberie Garantie Limitée DE UN AN Garantie DE LA Machine À Glaçons KitchenaidKitchenaid NE Prendra PAS EN Charge 2313715A

2313715A specifications

The KitchenAid 2313715A is a versatile and innovative kitchen gadget designed for home cooks who are looking to enhance their culinary experience. This food processor has become a staple in many kitchens due to its powerful performance and user-friendly design.

One of the standout features of the KitchenAid 2313715A is its powerful motor, which allows for efficient and quick processing of ingredients. This motor is designed to handle a variety of tasks, from chopping and slicing to mixing and pureeing. With multiple speed settings, users can easily adjust the power to suit their specific needs, ensuring that food is prepared to perfection.

In addition to its impressive motor, the KitchenAid 2313715A boasts a generous bowl capacity, allowing users to process larger quantities of food at once. This is particularly beneficial when preparing meals for families or gatherings, as it reduces the time spent on food prep. The bowl is also designed with a wide feed chute that accommodates whole fruits and vegetables, minimizing the need for pre-cutting and maximizing efficiency.

The design of the KitchenAid 2313715A is not only functional but also aesthetically pleasing. The sleek and modern appearance makes it an attractive addition to any kitchen countertop. Furthermore, the appliance is equipped with a variety of attachments, including slicing discs, shredding discs, and a metal blade, which provide users with added versatility for multiple culinary tasks.

Additionally, the KitchenAid 2313715A features a safety locking mechanism, ensuring that the processor operates only when securely assembled. This safety feature lends peace of mind, particularly for those who may be new to using kitchen appliances.

Maintenance and cleaning are also a breeze with this food processor. Most components are dishwasher-safe, making it easy to keep the appliance in optimal condition after use.

Overall, the KitchenAid 2313715A food processor stands out for its robust performance, user-friendly design, and aesthetic appeal. It incorporates cutting-edge technology while maintaining the reliability that KitchenAid is known for, making it an essential tool for both aspiring and experienced chefs alike. Whether you’re preparing everyday meals or exploring new recipes, the KitchenAid 2313715A is designed to elevate your cooking experience.
Top Page Image Contents