KitchenAid W10137649A Connect the Water Supply, Connect to Water Line, Connect to Refrigerator

Page 4

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

■Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

■Allow the storage tank on the reverse osmosis system to refill after heavy usage.

■If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. See “Water Filtration System.”

If you have questions about your water pressure, call a licensed, qualified plumber.

Connect the Water Supply

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.

Connect to Water Line

1.Unplug refrigerator or disconnect power.

2.Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3.Find a ¹⁄₂" to 1¹⁄₄" (12.7 mm to 3.18 mm) vertical cold water pipe near the refrigerator.

IMPORTANT:

■Make sure it is a cold water pipe.

■Horizontal pipe will work, but the following procedure must be followed: Drill on the top side of the pipe, not the bottom. This will help keep water away from the drill. This also keeps normal sediment from collecting in the valve.

4.Determine the length of copper tubing you need. Measure from the connection on the lower right rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5.Using a cordless drill, drill a ¹⁄₄" hole in the cold water pipe you have selected.

A

B

 

C

 

D

 

E

 

F

 

G

A. Cold water pipe

E. Compression sleeve

B. Pipe clamp

F. Shutoff valve

C. Copper tubing

G. Packing nut

D. Compression nut

 

6.Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the ¹⁄₄" drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.

7.Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

8.Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe.

Connect to Refrigerator

Depending on your model, the water line may come down from the top or up from the bottom. Follow the connection instructions for your model.

Style 1

1.Remove plastic cap from water valve inlet port. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Confirm copper tubing is secure by pulling on copper tubing.

2.Create a service loop with the copper tubing. Avoid kinks when coiling the copper tubing. Secure copper tubing to refrigerator cabinet with a “P” clamp.

A

B

C

D

E

A. Copper tubing

D. Compression sleeve

B. “P” clamp

E. Water valve inlet port

C. Compression nut

 

3.Turn on water supply to refrigerator and check for leaks. Correct any leaks.

Style 2

1.Create a service loop (minimum diameter of 2 ft [61 cm]) with the copper tubing. Avoid kinks when coiling the copper tubing.

2.Remove the plastic cap from water valve inlet port. Place a compression nut and sleeve on the copper tubing.

3.Insert the end of the copper tubing into the water valve inlet port. Shape tubing slightly so that the tubing feeds straight into the port to avoid kinks.

4.Slide the compression nut over the sleeve and screw into the water valve inlet port.

A

B

C

D

A. Plastic water tubing

C. Compression nut

B. Sleeve

D. Copper tubing

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Refrigerator Safety Refrigerator User InstructionsInstallation Instructions Clean Before UsingUnpack the Refrigerator Before You Throw Away Your Old Refrigerator or FreezerElectrical Requirements Location RequirementsWater Supply Requirements Connect the Water Supply Connect to Water LineConnect to Refrigerator StyleRefrigerator Door and Drawer Reverse Door Panel Series Replace Door and HingesFreezer Drawer Remove Drawer FrontDoor Swing Reversal optional Architect SeriesPanel Series Adjust the Door Factory Trim KitRemove the Door Panel Replace the Door PanelUsing the Controls Refrigerator USEElectronic Controls Digital ControlsCrisper Humidity Control Water Filtration System Ice MakerWater Dispenser Refrigerator Care CleaningChanging the Light Bulb Troubleshooting Refrigerator OperationTemperature and Moisture Ice and WaterWater is leaking from the dispenser system Water Filter CertificationsWater from the dispenser is warm Product Data Sheets Application Guidelines/Water Supply ParametersKitchenaid Refrigerator Warranty ONE Year Limited WarrantyItems Kitchenaid will not PAY for Disclaimer of Implied Warranties Limitation of RemediesInstructions Dutilisation DU Réfrigérateur Sécurité DU RéfrigérateurInstructions D’INSTALLATION Déballage du réfrigérateurAvant de jeter votre vieux réfrigérateur ou congélateur Enlèvement des matériaux d’emballageExigences demplacement Méthode recommandée de mise à la terreSpécifications électriques Spécifications de l’alimentation en eauRaccordement de la canalisation deau Pression de leauAlimentation en eau par osmose inverse Raccordement à une canalisation d’eauAchever l’installation Plastique Tube de cuivre Orifice darrivée deau Bride en PPorte et tiroir du réfrigérateur Remplacement de la porte et des charnières Retirer et réinstaller le tiroir du congélateurRéinstallation de la façade du tiroir Enlèvement de la façade du tiroirInversion du sens douverture des portes facultatif Série ArchitectSérie avec panneaux décoratifs Garniture de poignéeAjustement de la porte Ensemble décoratif de l’usineStyle 1-Nivellement avant et arrière Style 2- Vis pied de réglage de laplombRéinstallation du panneau de porte Installation des panneaux personnalisés en boisDimensions pour lusinage du panneau de porte Panneaux unis Dimensions pour les panneaux en bois personnalisésUtilisation des commandes Commandes électroniquesCommandes numériques Utilisation DU RéfrigérateurHoliday Mode mode vacances Temp Alarm alarme de dépassement de températurePour ajuster les réglages de température Caractéristique OptimIceRéglage de lhumidité dans le bac à légumes Machine à glaçonsRemplacement du filtre à eau Distributeur d’eauSystème de filtration de leau Distribution d’eauEntretien DU Réfrigérateur Remplacement de l’ampoule d’éclairageNettoyage Dépannage Fonctionnement du réfrigérateurTempérature et humidité Glaçons et eauLes portes sont difficiles à ouvrir La température est trop élevéeLes glaçons sont creux ou petits Goût, odeur ou couleur grise des glaçonsLe distributeur deau ne fonctionne pas correctement ’eau coule du système de distributionFeuilles DE Données SUR LE Produit Système de filtration d’eau intérieurGarantie DU Réfrigérateur Kitchenaid Garantie Limitée DE UN ANKitchenaid NE Prendra PAS EN Charge W10137649A SP PN W1013750AW10297791

W10137649A specifications

The KitchenAid W10137649A is a modern and versatile appliance designed to elevate your cooking experience. Known for its reliability and innovative features, this kitchen tool caters to both novice cooks and seasoned chefs.

One of the standout characteristics of the W10137649A is its exceptional build quality. Crafted with durable materials, it ensures longevity and withstands the rigors of daily use. The sleek design complements any kitchen aesthetic, making it both a functional and stylish addition to your culinary space.

The W10137649A is equipped with multiple speed settings, giving you precise control over your mixing, blending, and food preparation tasks. Whether you're whipping cream, kneading dough, or mixing batter, you can easily adjust the speed to suit your needs. This versatility is further enhanced by its powerful motor, which delivers consistent performance across various tasks.

Another key feature of the W10137649A is its user-friendly interface. The intuitive controls allow for effortless operation, making it easy to switch between different functions and speeds. Additionally, the appliance has a spacious bowl capacity, accommodating larger batches of ingredients with ease. This makes it perfect for families or individuals who love hosting gatherings and preparing large meals.

One of the notable technologies integrated into the W10137649A is its planetary mixing action. This unique design allows the mixing attachments to rotate in one direction while the bowl rotates in the opposite direction. As a result, ingredients are blended more thoroughly and evenly, reducing the need for manual scraping and ensuring consistent outcomes.

Moreover, the KitchenAid W10137649A comes with a variety of attachments, including a dough hook, balloon whisk, and flat beater, allowing you to tackle a wide range of culinary tasks. These accessories are easy to switch out and clean, further enhancing usability.

In summary, the KitchenAid W10137649A stands out as a premier choice for anyone looking to invest in a reliable and versatile kitchen appliance. Its combination of high-quality construction, user-friendly design, and innovative technologies make it an essential tool for creating delicious meals and baked goods. With this appliance in your kitchen, you'll be well-equipped to bring your culinary creations to life.
Top Page Image Contents