KitchenAid W10137649A Reverse Door Panel Series, Replace Door and Hinges, Freezer Drawer

Page 6

3.Remove the door stop from the bottom edge of the refrigerator door. Move to opposite side of refrigerator door as shown in Graphic 3.

4.Attach the door handle mounting posts to the opposite side of the door.

5.Position refrigerator handle over mounting posts as shown in Graphic 2. Drive two set screws in the sides of the handle.

6.Tighten all screws. Set aside the door until the hinges and freezer compartment drawer are in place.

Reverse Door (Panel Series)

IMPORTANT:

■If you want to reverse your door so it opens from the opposite side, follow these steps. If you are not reversing the door, see “Replace Door and Hinges.”

■You must first remove the handle from the panel series refrigerator door to reverse the door swing.

1.Using a flat-blade screwdriver tip wrapped in masking tape, remove the cabinet hinge hole plugs and move them to the opposite side of the cabinet as shown in Graphic 1.

2.Remove the hinge screws. Move to the opposite side of cabinet. See Graphic 2.

3.Using a Phillips screwdriver, remove the door stop and door cap located on the bottom edge of the refrigerator compartment. See Graphic 5.

4.Using a Phillips screwdriver, remove the top door cap.

5.Remove ¹⁄₄" hex-head screws from top door extension. Reverse the top door extension so the notched corner turns in toward the interior of the door. See Graphic 3.

6.Remove the side door trim and handle trim by tapping the bottom edges upward with a soft rubber mallet. The trim will slide up and release from the door. See Graphic 4.

7.Replace the bottom door cap and install the door stop on opposite side of the door. See Graphic 5.

8.Using the alternate side door trim, shipped with the refrigerator, align notches on trim with metal mounting tabs on side of door. Slide the trim down until it locks into place. Tap the top of the trim with a rubber mallet to ensure snug fit. See Graphic 4.

9.Install handle by aligning handle notches with metal mounting tabs on side of door. Slide the handle down until it locks. Tap top of handle with rubber mallet to ensure snug fit. See Graphic 4.

10.Using a Phillips screwdriver, install the top door cap. See Graphic 3.

Replace Door and Hinges

NOTE: When reversing panel series door, use alternate top hinge shipped with refrigerator.

1.Replace the parts for the bottom hinge as shown in Bottom Hinge graphic. Tighten screws. Replace the refrigerator door.

NOTE: Provide additional support for the refrigerator door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

2.Assemble the parts for the top hinge as shown in the Top Hinge Graphic. Do not tighten screws completely.

3.Line up the door so that the bottom of the refrigerator door aligns evenly with the top of the freezer drawer. Tighten all screws.

Freezer Drawer

IMPORTANT: Two people may be required to remove and replace the freezer drawer.

Remove Drawer Front

1.Open the freezer drawer to full extension.

2.Loosen the four screws attaching the drawer glides to the drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws in the drawer front.

3.Lift drawer front upward and off the screws. See Drawer Front Removal graphic.

Replace Drawer Front

1.Slide the drawer glides out of the freezer compartment. Insert the screws in the top of the drawer front into the slots in the drawer brackets. See Drawer Front Replacement graphic.

2.Pull the drawer brackets toward you to position the two screws in the bottom of the drawer front into the brackets. See Drawer Front Replacement graphic.

3.Completely tighten the four screws.

4.Replace the base grille.

Final Steps

1.Check all holes to make sure that hole plugs and screws are in place. Reinstall top hinge cover. See Top Hinge Graphic.

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

2.Plug into a grounded 3 prong outlet.

3.Return all removable door parts to doors and food to refrigerator.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Refrigerator Safety Refrigerator User InstructionsUnpack the Refrigerator Installation InstructionsClean Before Using Before You Throw Away Your Old Refrigerator or FreezerLocation Requirements Electrical RequirementsWater Supply Requirements Connect to Refrigerator Connect the Water SupplyConnect to Water Line StyleRefrigerator Door and Drawer Freezer Drawer Reverse Door Panel SeriesReplace Door and Hinges Remove Drawer FrontDoor Swing Reversal optional Architect SeriesPanel Series Remove the Door Panel Adjust the DoorFactory Trim Kit Replace the Door PanelUsing the Controls Refrigerator USEElectronic Controls Digital ControlsCrisper Humidity Control Ice Maker Water Filtration SystemWater Dispenser Cleaning Refrigerator CareChanging the Light Bulb Troubleshooting Refrigerator OperationTemperature and Moisture Ice and WaterWater Filter Certifications Water is leaking from the dispenser systemWater from the dispenser is warm Product Data Sheets Application Guidelines/Water Supply ParametersItems Kitchenaid will not PAY for Kitchenaid Refrigerator WarrantyONE Year Limited Warranty Disclaimer of Implied Warranties Limitation of RemediesInstructions Dutilisation DU Réfrigérateur Sécurité DU RéfrigérateurAvant de jeter votre vieux réfrigérateur ou congélateur Instructions D’INSTALLATIONDéballage du réfrigérateur Enlèvement des matériaux d’emballageSpécifications électriques Exigences demplacementMéthode recommandée de mise à la terre Spécifications de l’alimentation en eauAlimentation en eau par osmose inverse Raccordement de la canalisation deauPression de leau Raccordement à une canalisation d’eauAchever l’installation Plastique Tube de cuivre Orifice darrivée deau Bride en PPorte et tiroir du réfrigérateur Réinstallation de la façade du tiroir Remplacement de la porte et des charnièresRetirer et réinstaller le tiroir du congélateur Enlèvement de la façade du tiroirInversion du sens douverture des portes facultatif Série ArchitectSérie avec panneaux décoratifs Garniture de poignéeStyle 1-Nivellement avant et arrière Ajustement de la porteEnsemble décoratif de l’usine Style 2- Vis pied de réglage de laplombDimensions pour lusinage du panneau de porte Panneaux unis Réinstallation du panneau de porteInstallation des panneaux personnalisés en bois Dimensions pour les panneaux en bois personnalisésCommandes numériques Utilisation des commandesCommandes électroniques Utilisation DU RéfrigérateurPour ajuster les réglages de température Holiday Mode mode vacancesTemp Alarm alarme de dépassement de température Caractéristique OptimIceRéglage de lhumidité dans le bac à légumes Machine à glaçonsSystème de filtration de leau Remplacement du filtre à eauDistributeur d’eau Distribution d’eauRemplacement de l’ampoule d’éclairage Entretien DU RéfrigérateurNettoyage Dépannage Fonctionnement du réfrigérateurLes portes sont difficiles à ouvrir Température et humiditéGlaçons et eau La température est trop élevéeLe distributeur deau ne fonctionne pas correctement Les glaçons sont creux ou petitsGoût, odeur ou couleur grise des glaçons ’eau coule du système de distributionFeuilles DE Données SUR LE Produit Système de filtration d’eau intérieurKitchenaid NE Prendra PAS EN Charge Garantie DU Réfrigérateur KitchenaidGarantie Limitée DE UN AN W10137649A SP PN W1013750AW10297791

W10137649A specifications

The KitchenAid W10137649A is a modern and versatile appliance designed to elevate your cooking experience. Known for its reliability and innovative features, this kitchen tool caters to both novice cooks and seasoned chefs.

One of the standout characteristics of the W10137649A is its exceptional build quality. Crafted with durable materials, it ensures longevity and withstands the rigors of daily use. The sleek design complements any kitchen aesthetic, making it both a functional and stylish addition to your culinary space.

The W10137649A is equipped with multiple speed settings, giving you precise control over your mixing, blending, and food preparation tasks. Whether you're whipping cream, kneading dough, or mixing batter, you can easily adjust the speed to suit your needs. This versatility is further enhanced by its powerful motor, which delivers consistent performance across various tasks.

Another key feature of the W10137649A is its user-friendly interface. The intuitive controls allow for effortless operation, making it easy to switch between different functions and speeds. Additionally, the appliance has a spacious bowl capacity, accommodating larger batches of ingredients with ease. This makes it perfect for families or individuals who love hosting gatherings and preparing large meals.

One of the notable technologies integrated into the W10137649A is its planetary mixing action. This unique design allows the mixing attachments to rotate in one direction while the bowl rotates in the opposite direction. As a result, ingredients are blended more thoroughly and evenly, reducing the need for manual scraping and ensuring consistent outcomes.

Moreover, the KitchenAid W10137649A comes with a variety of attachments, including a dough hook, balloon whisk, and flat beater, allowing you to tackle a wide range of culinary tasks. These accessories are easy to switch out and clean, further enhancing usability.

In summary, the KitchenAid W10137649A stands out as a premier choice for anyone looking to invest in a reliable and versatile kitchen appliance. Its combination of high-quality construction, user-friendly design, and innovative technologies make it an essential tool for creating delicious meals and baked goods. With this appliance in your kitchen, you'll be well-equipped to bring your culinary creations to life.
Top Page Image Contents