Hotpoint DX 892 CX S manual Installation

Page 5

Installation

Electrical Requirements

For your own safety, we recommend that your cooker is installed by a competent person such as one who is registered with NICEIC (National Inspection Council for Electrical Installation Contracting). The cooker should be installed in accordance with the latest edition of the IEE Regulations.

Warning: This appliance must be earthed.

Electrical Connections

The installer must check that the voltage shown on the rating plate corresponds with the house electricity supply. The cooker must be supplied via a suitable double pole isolating switch, having a contact separation of at least 3mm in all poles placed in a readily accessible position adjacent to the cooker. If the cooker is to be wired into a connector unit, this may be positioned behind the cooker providing the following requirements are met:

i)The connector unit must not project from the wall more than 25mm.

ii)The top of the connector must not be more than 130mm above floor level.

Remove the terminal cover at the rear base of the cooker. Pass the cable through the cable clamp and connect to the appropriate terminals provided. Allow sufficient cable for any future servicing.

Tighten the screws on the cable clamp and replace the cover. Make main connections in the connector unit or cooker control unit. This appliance conforms to B.S. EN 55014 regarding suppression of Radio and Television reception interference.

A double Pole control switch having a minimum rating of 32 amps should be used to feed the cooker using a suitably rated cable. Where a hob is fitted adjacent to or over the cooker, a 45 amp Double Pole control switch should be used to feed both units via separate suitably rated cables.

We recommend a minimum of 4mm2 PVC insulated twin and earth cable conforming to B.S. 6004 for connection of each appliance.

In all cases adhere to routing details (see fig. 4).

This appliance must not be installed over any other appliance that generates heat such as a plinth heater.

Note: Due to many different types of installation, a mains cable is not supplied with this product. The installer will fit the correct type and length of cable.

Important

It is essential that the lower cupboard is constructed

in the manner illustrated i.e. having side, back, and

roof panels so joined as to provide no apertures which GB could permit access to the oven unit when installed.

1. General

The appliance is designed for mounting at a safe level into an oven housing which must be secured to the backing wall.

2. Ventilation

a.The oven housing unit cabinet dimensions must comply with fig. 4.

b.An air gap of 50mm minimum must be provided at the rear of any top or bottom cupboards or shelves (see fig. 1).

c.It is necessary that the cabinets are provided with unobstructed ventilation, i.e. from adjacent cabine- try. This can be done by either raising the base of the cabinets using the adjusting feet (or spacers) or alternatively by providing a slot in the cabinet plinth to the dimensions in fig. 1.

d.The air gap at rear allows the warmed air to pass out of the inner cabinet space. Where it is intended to fit cupboards above the oven unit to ceiling height, it is essential that the warmed air is exhausted through the front of the cabinet (see fig. 1).

e.If an oven unit is installed adjacent to a tall cabinet, steam escaping from the oven when the door is opened could condense on and maybe stain the adjacent surface. To prevent permanent staining, the adjacent surface should be made of a material that is heat resisting and easy to clean. Adjacent tall cabinets should not be deeper than the oven housing cabinet.

3. Final Installation

a.Using a spirit level, check that the housing cabinet is level from side to side and from front to back in its installed position.

b.Correct any unevenness by placing spacers under the bottom of the cabinet. Make sure that the cabi- net rests firmly on the floor without rocking.

c.Before the oven is fitted, the cabinet must be firmly secured to the backing wall for stability.

d.The oven unit should now be lifted (this is a two person lift) into the cabinet and pushed fully home.

e.Finally, the oven is secured to the cabinet by means of the four Phillips C/SK Head screws - two through each side trim.

f.Remove all packaging material from the grill and oven interior.

List of loose items:

4 x Phillips C/SK Head No. 6 x 25mm screws.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Build-in Electric double oven Contents Instructions for Installation and UseVery HOT Surfaces Has been correctly installed To the InstallerIntroduction To the UserNever Safety InformationAlways Installation Tall Cabinet Ventilation 562mm 561mmOverall view Control panel Main parts of your Double OvenDisplay Available only on certain modelsSetting the minute minder Setting the clockStart-up and use Control panel lockResidual heat indicators Restoring the factory settingsStandby Cooling ventilationAutomatic cooking modes Cooking Modes in your OvenManual cooking modes Make a small well in the mound of flour Select the manual LOW Temperature functionPour in the water and yeast mixture Knead the dough by stretching and folding it overSetting the end time for a cooking mode Practical cooking adviceProgramming cooking Programming the cooking durationSolarplus Grill Using the grill pan kit To use the oven proceed as follows Top Oven Conventional Cooking∙ Do not place food or dishes on the floor of the oven Platewarming in the top ovenMeat Pre-heat Temperature Time approx Top Oven Temperature Charts MeatFood Pre-heat Temperature Time in mins Position in Oven Top Oven Temperature Charts BakingTelescopic runners and Meat pan Cooking temperature rangesMain Oven Intelligent Cooking System Main Oven The Intelligent Cooking System Cooking Advice TableGas Main Main Fan Temperature Conversion ChartTop Oven Sides, Main Oven Sides Rear Panel Care and CleaningInner Door Panels & Glass Control PanelRefit the door inner glass as follows Remove the door inner glass as followsThere MAY be Nothing Wrong If something Goes wrongDisposal of your product Positions 1 and 5 the direct We recommend switchingClock button Digits on the display flashGuarantee is subject to the following conditions Months Parts and Labour GuaranteeGuarantee does not cover Year Parts GuaranteeParts & Accessories Hotpoint ServiceRepublic of Ireland 0818 313 Appliance Registration

DX 892 CX S specifications

The Hotpoint DX 892 CX S is a state-of-the-art dishwasher designed to meet the demands of modern households. With an elegant stainless steel finish, it not only enhances kitchen aesthetics but also delivers exceptional performance and efficiency. This versatile appliance boasts a capacity of up to 16 place settings, making it ideal for large families or those who frequently entertain.

One of the standout features of the DX 892 CX S is its advanced cleaning technology. The dishwasher is equipped with Hotpoint’s unique Power Clean Pro system, which uses specially designed jet sprays to target heavily soiled dishes. This ensures that even the toughest baked-on food is removed, providing a sparkling clean every time. Complementing this is the Smart Sensor technology that automatically detects the level of dirt in the load and adjusts the washing cycle accordingly. This leads to not only superior cleaning results but also optimizes water and energy consumption.

The DX 892 CX S is built with flexibility in mind. The adjustable top basket allows for taller items to fit comfortably in the lower basket, while the folding tines provide additional space customization. This means that whether you're washing large pots, delicate glassware, or a mixture of both, this dishwasher can accommodate your needs.

Another significant feature is the Eco Cycle program, which is designed to minimize energy use without compromising on cleaning performance. With an impressive Energy Rating, this model contributes to both environmental sustainability and lower utility bills. Additionally, the dishwasher operates at a whisper-quiet noise level, ensuring a tranquil home environment even during nighttime cycles.

For added convenience, the Hotpoint DX 892 CX S includes a delay timer, allowing you to set the dishwasher to run at a time that best suits your schedule. The intuitive digital display makes selecting programs and monitoring progress easy, ensuring a user-friendly experience.

With its combination of practicality, efficiency, and cutting-edge technology, the Hotpoint DX 892 CX S stands out as an exemplary choice for anyone seeking a reliable and stylish dishwasher solution. It efficiently complements modern lifestyles while ensuring outstanding performance in dish cleaning.
Top Page Image Contents