Delta 34-806, 36-812, 34-814 Operating Controls Unisaw Adjustments, Starting and Stopping the SAW

Page 14

OPERATING CONTROLS

AND UNISAW ADJUSTMENTS

STARTING AND STOPPING THE SAW

To start the machine, push “ON” button (A) Fig. 39. To stop the machine, push “OFF” button (B).

LOCKING SWITCH

IN THE “OFF” POSITION

IMPORTANT: When the machine is not in use, the switch should be locked in the “OFF” position using a padlock

(A)Fig. 40, (Delta Cat. No. 50-325), with a 3/16" diameter shackle to prevent unauthorized use. NOTE: GPE switch shown.

OVERLOAD PROTECTION

Your saw is supplied with overload protection. If the motor shuts off or fails to start due to overloading (cutting stock too fast, using a dull blade, using the saw beyond its capacity, etc.) or low voltage, let the motor cool three to five minutes. The overload will automatically reset itself and the machine can then be started again by pressing the “ON” button.

IMPORTANT: If the motor continually shuts off due to overloading, the cause of overloading must be corrected. If this happens, it is recommended that you contact a qualified electrician.

BLADE RAISING

MECHANISM

The saw blade is raised and lowered with the front handwheel (A) Fig. 41. With the exception of hollow ground blades, the blade should be raised 1/8" to 1/4" above the top surface of the material being cut. With hollow ground blades, the blade should be raised the maximum to provide greater clearance. To raise the saw blade, loosen lock knob (B) Fig. 41, and turn the handwheel (A), clockwise. To lower the saw blade, turn handwheel (A) counterclockwise.

The saw blade is locked at any height by turning the lock knob (B) Fig. 41, clockwise. Due to the wedge action of this locking device, only a small amount of force is required to lock the blade raising mechanism securely. Any added force merely puts unnecessary strain on the locking device. Limit stops for raising or lowering are permanently built into the mechanism and need no further adjustment.

A

B

Fig. 39

A

Fig. 40

A

B

D

E

C

Fig. 41

BLADE TILTING MECHANISM

The blade tilting mechanism allows the blade to be tilted up to 45 degrees to the right.

To tilt the saw blade to the desired angle, loosen lock knob (D) Fig. 41, and turn handwheel (C). A pointer indicates the angle of tilt on scale (E), which is marked in one-degree increments. To lock the saw blade in the desired angle of tilt, tighten lock knob (D).

IMPORTANT: ALWAYS LOCK THE BLADE IN POSITION BEFORE STARTING THE SAW.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Unisaw 10 Right Tilting Arbor Saw General Safety Rules Additional Safety Rules for Circular Saws Refer to them often Use them to instruct othersGrounding Instructions Power ConnectionsMotor Specifications Magnetic Push Button Controls Five Horsepower MotorsThree Phase Operation Extension CordsUnpacking and Cleaning Operating InstructionsAssembling Extension Wing Assembly InstructionsAssembling Blade Tilting Mechanism Handle Assembling LVC ON/OFF Switch Assembling LVC Starter BOX to CabinetAssembling GPE ON/OFF Switch Assembling Blade Guard and Splitter AssemblyAdjust splitter bracket a until it is aligned Page Attaching Motor Cover Fastening Motor Cord to SAW FrameAssembling Dust Chute Adapter Miter Gage Holder and Wrench HolderAssembling RIP Fence Holder Brackets Operating Controls Unisaw Adjustments Starting and Stopping the SAWAdjusting 90 and 45 Degree Positive Stops Adjusting TableAdjusting Table Insert Miter Gage Operation and AdjustmentChanging the SAW Blade MaintenanceReplacing Belts and Adjusting Belt Tension CROSS-CUTTING OperationsProtecting Cast Iron Table from Rust Using the Fence AS a CUT-OFF Gage RippingUsing Accessory Moulding Cutterhead Using Auxiliary Wood Facing on Biesemeyer RIP FenceUsing Auxiliary Wood Facing on the Unifence Always Install Blade Guard After Operation is Compete Using Accessory Dado Head Constructing a Featherboard Pushstick Constructing a Push StickBlade Guard Accessories Deluxe Uniguard Blade GuardAccessories PARTS, Service or Warranty Assistance Page Canadian PORTER-CABLE Delta Service Centers
Related manuals
Manual 28 pages 27.85 Kb

34-801, 34-806, 34-814, 36-812 specifications

Delta has long been a reputable name in the woodworking industry, and its line of table saws, including models such as the Delta 36-812, 34-814, 34-806, and 34-801, exemplifies the brand's commitment to quality and innovation. Each of these models offers unique features and technologies tailored to meet the needs of both professional woodworkers and hobbyists.

The Delta 36-812 is a compact yet powerful table saw designed for versatility and efficiency. This model features a 15-amp motor, capable of delivering 4,800 RPM, providing sufficient power for cutting through various materials including hardwood and softwood. One of the standout features of the 36-812 is its Portable Stand, which allows easy transportation and setup without compromising stability. The saw also boasts a large, adjustable rip fence, ensuring accuracy when making long cuts.

Next in line is the Delta 34-814, which takes things up a notch with its more advanced design. This cabinet saw is built with a one-piece, rigid steel frame that minimizes vibrations, contributing to cleaner cuts. The 34-814 also features a 1.5 HP motor, providing reliable power and performance in any workshop setting. Its patented Quick-Build T-Square System offers smooth adjustments for crosscuts and rip cuts, enhancing user convenience, while the large table surface provides plenty of workspace for larger projects.

For those looking for a reliable saw that combines performance with compactness, the Delta 34-806 makes a strong case. This model is equipped with a 1 HP motor and features a sturdy, lightweight construction which makes it ideal for smaller workshops or job sites. It boasts a patented fence system that is easy to use and adjust, along with a durable blade guard for enhanced safety. The compact design does not sacrifice cutting power, allowing woodworkers to tackle a variety of materials with ease.

Lastly, the Delta 34-801 is a classic contractor saw that captures the essence of performance and portability. It features a powerful 1.5 HP motor and a 30-inch rip capacity, perfect for larger woods and panels. The saw includes an easy-to-use rack and pinion fence system that improves accuracy and alignment. Its folding stand allows for effortless storage, making it a great option for those who need to maximize space.

In summary, the Delta 36-812, 34-814, 34-806, and 34-801 are all exemplary offerings in Delta's lineup, each designed with specific features and capabilities. From compact options to more robust cabinet designs, these saws cater to the diverse needs of woodworkers across various skill levels and applications. With their combination of power, precision, and innovative technologies, they continue to uphold Delta's legacy of excellence in woodworking tools.
Top Page Image Contents