Delta 34-801, 36-812, 34-814, 34-806 Refer to them often Use them to instruct others

Page 3

ADDITIONAL SAFETY RULES FOR

CIRCULAR SAWS

WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY

1.DO NOT OPERATE THIS MACHINE until it is assembled and installed according to the instructions.

2.OBTAIN ADVICE FROM YOUR SUPERVISOR, instructor, or another qualified person if you are not familiar with the operation of this machine.

3.FOLLOW ALL WIRING CODES and recommended electrical connections.

4.USE THE GUARDS WHENEVER POSSIBLE. Check to see that they are in place, secured, and working correctly.

5.AVOID KICKBACK by:

A.keeping blade sharp and free of rust and pitch.

B.keeping rip fence parallel to the saw blade.

C.using saw blade guard and spreader for every possible operation, including all through sawing.

D.pushing the workpiece past the saw blade prior to release.

E.never ripping a workpiece that is twisted or warped, or does not have a straight edge to guide along the fence.

F.using feather boards when the anti-kickback device cannot be used.

G.never sawing a large workpiece that cannot be controlled.

H.never using the fence as a guide when crosscutting.

I.never sawing a workpiece with loose knots or other flaws.

6.ALWAYS USE GUARDS, SPLITTER, AND ANTI- KICKBACK FINGERS except when otherwise directed in the manual.

7.REMOVE CUT-OFF PIECES AND SCRAPS from the table before starting the saw. The vibration of the machine may cause them to move into the saw blade and be thrown out. After cutting, turn the machine off. When the blade has come to a complete stop, remove all debris.

8.NEVER START THE MACHINE with the workpiece against the blade.

9.HOLD THE WORKPIECE FIRMLY against the miter gauge or fence.

10.NEVER run the workpiece between the fence and a moulding cutterhead.

11.NEVER perform “free-hand” operations. Use either the fence or miter gauge to position and guide the workpiece.

12.USE PUSH STICK(S) for ripping a narrow workpiece.

13.AVOID AWKWARD OPERATIONS AND HAND POSITIONS where a sudden slip could cause a hand to move into the blade.

14.KEEP ARMS, HANDS, AND FINGERS away from the blade.

15.NEVER have any part of your body in line with the path of the saw blade.

16.NEVER REACH AROUND or over the saw blade.

17.NEVER attempt to free a stalled saw blade without first turning the machine “OFF”.

18.PROPERLY SUPPORT LONG OR WIDE workpieces.

19.NEVER PERFORM LAYOUT, assembly or set-up work on the table/work area when the machine is running.

20.TURN THE MACHINE “OFF” AND DISCONNECT THE MACHINE from the power source before installing or removing accessories, before adjusting or changing set-ups, or when making repairs.

21.TURN THE MACHINE “OFF”, disconnect the machine from the power source, and clean the table/work area before leaving the machine. LOCK THE SWITCH IN THE “OFF” POSITION to prevent unauthorized use.

22.ADDITIONAL INFORMATION regarding the safe and proper operation of this tool is available from the Power Tool Institute, 1300 Summer Avenue, Cleveland, OH 44115-2851. Information is also available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Please refer to the American National Standards Institute ANSI 01.1 Safety Requirements for Woodworking Machines and the U.S. Department of Labor OSHA 1910.213 Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often

and use them to instruct others.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Unisaw 10 Right Tilting Arbor Saw General Safety Rules Refer to them often Use them to instruct others Additional Safety Rules for Circular SawsPower Connections Motor SpecificationsGrounding Instructions Extension Cords Five Horsepower MotorsThree Phase Operation Magnetic Push Button ControlsOperating Instructions Unpacking and CleaningAssembly Instructions Assembling Blade Tilting Mechanism HandleAssembling Extension Wing Assembling LVC Starter BOX to Cabinet Assembling LVC ON/OFF SwitchAssembling Blade Guard and Splitter Assembly Assembling GPE ON/OFF SwitchAdjust splitter bracket a until it is aligned Page Fastening Motor Cord to SAW Frame Attaching Motor CoverMiter Gage Holder and Wrench Holder Assembling RIP Fence Holder BracketsAssembling Dust Chute Adapter Starting and Stopping the SAW Operating Controls Unisaw AdjustmentsAdjusting Table Adjusting 90 and 45 Degree Positive StopsMiter Gage Operation and Adjustment Adjusting Table InsertMaintenance Replacing Belts and Adjusting Belt TensionChanging the SAW Blade Operations Protecting Cast Iron Table from RustCROSS-CUTTING Ripping Using the Fence AS a CUT-OFF GageUsing Auxiliary Wood Facing on Biesemeyer RIP Fence Using Auxiliary Wood Facing on the UnifenceUsing Accessory Moulding Cutterhead Always Install Blade Guard After Operation is Compete Using Accessory Dado Head Constructing a Featherboard Constructing a Push Stick PushstickDeluxe Uniguard Blade Guard Blade Guard AccessoriesAccessories PARTS, Service or Warranty Assistance Page Canadian PORTER-CABLE Delta Service Centers
Related manuals
Manual 28 pages 27.85 Kb

34-801, 34-806, 34-814, 36-812 specifications

Delta has long been a reputable name in the woodworking industry, and its line of table saws, including models such as the Delta 36-812, 34-814, 34-806, and 34-801, exemplifies the brand's commitment to quality and innovation. Each of these models offers unique features and technologies tailored to meet the needs of both professional woodworkers and hobbyists.

The Delta 36-812 is a compact yet powerful table saw designed for versatility and efficiency. This model features a 15-amp motor, capable of delivering 4,800 RPM, providing sufficient power for cutting through various materials including hardwood and softwood. One of the standout features of the 36-812 is its Portable Stand, which allows easy transportation and setup without compromising stability. The saw also boasts a large, adjustable rip fence, ensuring accuracy when making long cuts.

Next in line is the Delta 34-814, which takes things up a notch with its more advanced design. This cabinet saw is built with a one-piece, rigid steel frame that minimizes vibrations, contributing to cleaner cuts. The 34-814 also features a 1.5 HP motor, providing reliable power and performance in any workshop setting. Its patented Quick-Build T-Square System offers smooth adjustments for crosscuts and rip cuts, enhancing user convenience, while the large table surface provides plenty of workspace for larger projects.

For those looking for a reliable saw that combines performance with compactness, the Delta 34-806 makes a strong case. This model is equipped with a 1 HP motor and features a sturdy, lightweight construction which makes it ideal for smaller workshops or job sites. It boasts a patented fence system that is easy to use and adjust, along with a durable blade guard for enhanced safety. The compact design does not sacrifice cutting power, allowing woodworkers to tackle a variety of materials with ease.

Lastly, the Delta 34-801 is a classic contractor saw that captures the essence of performance and portability. It features a powerful 1.5 HP motor and a 30-inch rip capacity, perfect for larger woods and panels. The saw includes an easy-to-use rack and pinion fence system that improves accuracy and alignment. Its folding stand allows for effortless storage, making it a great option for those who need to maximize space.

In summary, the Delta 36-812, 34-814, 34-806, and 34-801 are all exemplary offerings in Delta's lineup, each designed with specific features and capabilities. From compact options to more robust cabinet designs, these saws cater to the diverse needs of woodworkers across various skill levels and applications. With their combination of power, precision, and innovative technologies, they continue to uphold Delta's legacy of excellence in woodworking tools.
Top Page Image Contents