Delta 36-812, 34-814, 34-806 Power Connections, Motor Specifications, Grounding Instructions

Page 4

POWER CONNECTIONS

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3- prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the motor to the power line, make sure the switch is in the “OFF” position and be sure that the electric current is of the same characteristics as indicated on the machine. All line connections should make good contact. Running on low voltage will damage the motor.

WARNING: DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.

MOTOR SPECIFICATIONS

Your machine is wired for 230 volt, 60 HZ alternating current. Before connecting the tool to the power source, make sure the switch is in the “OFF” position.

GROUNDING INSTRUCTIONS

WARNING: THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK.

1. All grounded, cord-connected machines:

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This machine is equipped with an electric cord having an equipment- grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment- grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood,

or if in doubt as to whether the machine is properly grounded.

Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that accept the machine’s plug, as shown in Fig. C.

Repair or replace damaged or worn cord immediately.

2.Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating between 150 - 250 volts, inclusive:

This machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. C. The machine has a grounding plug that looks like the plug illustrated in Fig. C. Make sure the machine is connected to an outlet having the same configuration as the plug. No adapter is available or should be used with this machine. If the machine must be reconnected for use on a different type of electric circuit, the reconnection should be made by qualified service personnel; and after reconnection, the machine should comply with all local codes and ordinances.

3. Permanently connected machines:

This machine should be connected to a grounded metal permanent wiring system; or to a system having a equipment-grounding conductor.

WARNING: IN ALL CASES, MAKE CERTAIN THE RECEPTACLE IN QUESTION IS PROPERLY GROUNDED. IF YOU ARE NOT SURE HAVE A QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE.

GROUNDED OUTLET BOX

CURRENT CARRYING

PRONGS

240 VOLT

GROUND

PRONG

Fig. C

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Unisaw 10 Right Tilting Arbor Saw General Safety Rules Additional Safety Rules for Circular Saws Refer to them often Use them to instruct othersMotor Specifications Power ConnectionsGrounding Instructions Five Horsepower Motors Three Phase OperationMagnetic Push Button Controls Extension CordsUnpacking and Cleaning Operating InstructionsAssembling Blade Tilting Mechanism Handle Assembly InstructionsAssembling Extension Wing Assembling LVC ON/OFF Switch Assembling LVC Starter BOX to CabinetAssembling GPE ON/OFF Switch Assembling Blade Guard and Splitter AssemblyAdjust splitter bracket a until it is aligned Page Attaching Motor Cover Fastening Motor Cord to SAW FrameAssembling RIP Fence Holder Brackets Miter Gage Holder and Wrench HolderAssembling Dust Chute Adapter Operating Controls Unisaw Adjustments Starting and Stopping the SAWAdjusting 90 and 45 Degree Positive Stops Adjusting TableAdjusting Table Insert Miter Gage Operation and AdjustmentReplacing Belts and Adjusting Belt Tension MaintenanceChanging the SAW Blade Protecting Cast Iron Table from Rust OperationsCROSS-CUTTING Using the Fence AS a CUT-OFF Gage RippingUsing Auxiliary Wood Facing on the Unifence Using Auxiliary Wood Facing on Biesemeyer RIP FenceUsing Accessory Moulding Cutterhead Always Install Blade Guard After Operation is Compete Using Accessory Dado Head Constructing a Featherboard Pushstick Constructing a Push StickBlade Guard Accessories Deluxe Uniguard Blade GuardAccessories PARTS, Service or Warranty Assistance Page Canadian PORTER-CABLE Delta Service Centers
Related manuals
Manual 28 pages 27.85 Kb

34-801, 34-806, 34-814, 36-812 specifications

Delta has long been a reputable name in the woodworking industry, and its line of table saws, including models such as the Delta 36-812, 34-814, 34-806, and 34-801, exemplifies the brand's commitment to quality and innovation. Each of these models offers unique features and technologies tailored to meet the needs of both professional woodworkers and hobbyists.

The Delta 36-812 is a compact yet powerful table saw designed for versatility and efficiency. This model features a 15-amp motor, capable of delivering 4,800 RPM, providing sufficient power for cutting through various materials including hardwood and softwood. One of the standout features of the 36-812 is its Portable Stand, which allows easy transportation and setup without compromising stability. The saw also boasts a large, adjustable rip fence, ensuring accuracy when making long cuts.

Next in line is the Delta 34-814, which takes things up a notch with its more advanced design. This cabinet saw is built with a one-piece, rigid steel frame that minimizes vibrations, contributing to cleaner cuts. The 34-814 also features a 1.5 HP motor, providing reliable power and performance in any workshop setting. Its patented Quick-Build T-Square System offers smooth adjustments for crosscuts and rip cuts, enhancing user convenience, while the large table surface provides plenty of workspace for larger projects.

For those looking for a reliable saw that combines performance with compactness, the Delta 34-806 makes a strong case. This model is equipped with a 1 HP motor and features a sturdy, lightweight construction which makes it ideal for smaller workshops or job sites. It boasts a patented fence system that is easy to use and adjust, along with a durable blade guard for enhanced safety. The compact design does not sacrifice cutting power, allowing woodworkers to tackle a variety of materials with ease.

Lastly, the Delta 34-801 is a classic contractor saw that captures the essence of performance and portability. It features a powerful 1.5 HP motor and a 30-inch rip capacity, perfect for larger woods and panels. The saw includes an easy-to-use rack and pinion fence system that improves accuracy and alignment. Its folding stand allows for effortless storage, making it a great option for those who need to maximize space.

In summary, the Delta 36-812, 34-814, 34-806, and 34-801 are all exemplary offerings in Delta's lineup, each designed with specific features and capabilities. From compact options to more robust cabinet designs, these saws cater to the diverse needs of woodworkers across various skill levels and applications. With their combination of power, precision, and innovative technologies, they continue to uphold Delta's legacy of excellence in woodworking tools.
Top Page Image Contents