Delta 34-814, 36-812, 34-806, 34-801 Always Install Blade Guard After Operation is Compete

Page 21

IMPORTANT: For certain cutting operations such as dadoing and moulding where you are not cutting completely through the workpiece, the blade guard and splitter assembly cannot be used. Loosen screws (G) and

(H)Fig. 65. Lift up and swing blade guard and splitter assembly (W) Fig. 66, to the rear of the saw, and then tighten screws (G) and (H). CAUTION: Always return and fasten the blade guard and splitter assembly to its proper operating position for normal thru-sawing operations.

The moulding cutterhead (A) Fig. 67, is assembled to the saw arbor as shown. NOTE: THE OUTSIDE ARBOR

FLANGE CAN NOT BE USED WITH THE MOULDING CUTTERHEAD, TIGHTEN THE ARBOR NUT AGAINST THE CUTTERHEAD BODY. DO NOT LOOSE THE OUTSIDE ARBOR FLANGE, FOR IT WILL BE NEEDED WHEN REATTACHING A BLADE TO THE UNISAW ARBOR. ALSO, THE ACCESSORY MOULDING CUTTERHEAD TABLE INSERT (B), MUST BE USED IN PLACE OF THE STANDARD TABLE INSERT.

It is necessary when using the moulding cutterhead to add wood-facing (C) to the face of the rip fence, as shown in Fig. 68. The wood-facing is attached to the biesemeyer fence with two clamps, as shown (refer to the Unifence section of this manual for attaching wood facing to a Unifence). 3/4 inch stock is suitable for most work although an occasional job may require 1 inch facing.

Position the wood-facing over the cutterhead with the cutterhead below the surface of the table. Turn the saw on and raise the cutterhead. The cutterhead will cut its own groove in the wood-facing. Fig. 68, shows a typical moulding operation. NEVER USE MOULDING CUTTER-

HEAD IN A BEVEL POSITION.

IMPORTANT: NEVER RUN THE STOCK BETWEEN THE FENCE AND THE MOULDING CUTTERHEAD AS IRRE- GULAR SHAPED WOOD WILL CAUSE KICKBACK.

When moulding end grain, the miter gage is used. The feed should be slowed up at the end of the cut to prevent splintering.

In all cuts, attention should be given the grain, making the cut in the same direction as the grain whenever possible.

ALWAYS INSTALL BLADE GUARD AFTER OPERATION IS COMPETE.

H

G

Fig. 65

W

Fig. 66

Fig. 67

C

Fig. 68

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Unisaw 10 Right Tilting Arbor Saw General Safety Rules Refer to them often Use them to instruct others Additional Safety Rules for Circular SawsPower Connections Motor SpecificationsGrounding Instructions Three Phase Operation Five Horsepower MotorsMagnetic Push Button Controls Extension CordsOperating Instructions Unpacking and CleaningAssembly Instructions Assembling Blade Tilting Mechanism HandleAssembling Extension Wing Assembling LVC Starter BOX to Cabinet Assembling LVC ON/OFF SwitchAssembling Blade Guard and Splitter Assembly Assembling GPE ON/OFF SwitchAdjust splitter bracket a until it is aligned Page Fastening Motor Cord to SAW Frame Attaching Motor CoverMiter Gage Holder and Wrench Holder Assembling RIP Fence Holder BracketsAssembling Dust Chute Adapter Starting and Stopping the SAW Operating Controls Unisaw AdjustmentsAdjusting Table Adjusting 90 and 45 Degree Positive StopsMiter Gage Operation and Adjustment Adjusting Table InsertMaintenance Replacing Belts and Adjusting Belt TensionChanging the SAW Blade Operations Protecting Cast Iron Table from RustCROSS-CUTTING Ripping Using the Fence AS a CUT-OFF GageUsing Auxiliary Wood Facing on Biesemeyer RIP Fence Using Auxiliary Wood Facing on the UnifenceUsing Accessory Moulding Cutterhead Always Install Blade Guard After Operation is Compete Using Accessory Dado Head Constructing a Featherboard Constructing a Push Stick PushstickDeluxe Uniguard Blade Guard Blade Guard AccessoriesAccessories PARTS, Service or Warranty Assistance Page Canadian PORTER-CABLE Delta Service Centers
Related manuals
Manual 28 pages 27.85 Kb

34-801, 34-806, 34-814, 36-812 specifications

Delta has long been a reputable name in the woodworking industry, and its line of table saws, including models such as the Delta 36-812, 34-814, 34-806, and 34-801, exemplifies the brand's commitment to quality and innovation. Each of these models offers unique features and technologies tailored to meet the needs of both professional woodworkers and hobbyists.

The Delta 36-812 is a compact yet powerful table saw designed for versatility and efficiency. This model features a 15-amp motor, capable of delivering 4,800 RPM, providing sufficient power for cutting through various materials including hardwood and softwood. One of the standout features of the 36-812 is its Portable Stand, which allows easy transportation and setup without compromising stability. The saw also boasts a large, adjustable rip fence, ensuring accuracy when making long cuts.

Next in line is the Delta 34-814, which takes things up a notch with its more advanced design. This cabinet saw is built with a one-piece, rigid steel frame that minimizes vibrations, contributing to cleaner cuts. The 34-814 also features a 1.5 HP motor, providing reliable power and performance in any workshop setting. Its patented Quick-Build T-Square System offers smooth adjustments for crosscuts and rip cuts, enhancing user convenience, while the large table surface provides plenty of workspace for larger projects.

For those looking for a reliable saw that combines performance with compactness, the Delta 34-806 makes a strong case. This model is equipped with a 1 HP motor and features a sturdy, lightweight construction which makes it ideal for smaller workshops or job sites. It boasts a patented fence system that is easy to use and adjust, along with a durable blade guard for enhanced safety. The compact design does not sacrifice cutting power, allowing woodworkers to tackle a variety of materials with ease.

Lastly, the Delta 34-801 is a classic contractor saw that captures the essence of performance and portability. It features a powerful 1.5 HP motor and a 30-inch rip capacity, perfect for larger woods and panels. The saw includes an easy-to-use rack and pinion fence system that improves accuracy and alignment. Its folding stand allows for effortless storage, making it a great option for those who need to maximize space.

In summary, the Delta 36-812, 34-814, 34-806, and 34-801 are all exemplary offerings in Delta's lineup, each designed with specific features and capabilities. From compact options to more robust cabinet designs, these saws cater to the diverse needs of woodworkers across various skill levels and applications. With their combination of power, precision, and innovative technologies, they continue to uphold Delta's legacy of excellence in woodworking tools.
Top Page Image Contents