Installation, Unpacking & Inspection, Setup

INSTALLATION

NOTE: DO NOT discard the carton or other packing materials until you have inspected the appliance for hidden damage and tested it for proper operation.

Refer to SHIPPING DAMAGE CLAIM PROCEDURE on the inside front cover of this manual.

CAUTION:

RISK OF

DAMAGE

DO NOT connect or energize this appliance until all installation instructions are read and followed. Damage to the appliance will result if these instructions are not followed.

CAUTION:

SHOCK HAZARD

This appliance must be plugged into a properly installed and grounded electrical receptacle.

IMPORTANT:

If an appropriate electrical receptacle is not readily accessible, contact a licensed electrician to install the appropriate electrical receptacle.

240 volt units are shipped without a power plug. Contact a licensed electrician to install a power plug appropriate to local electrical codes.

IMPORTANT: Damage due to being connected to the wrong voltage or phase is NOT covered by warranty.

UNPACKING & INSPECTION

Carefully remove the appliance from the carton. Remove all protective plastic film, packing materials and accessories from the appliance before connecting electrical power or otherwise performing any installation procedure.

Carefully read all instructions in this manual and the Installation Instruction Sheet packed with the appliance before starting any installation.

Read and understand all labels and diagrams attached to the appliance.

Carefully account for all components and accessories before discarding packing materials. Store all accessories in a convenient place for later use.

COMPONENTS: Tray

Drop Door

Heat Lamp and Heat Lamp Guard Kettle Assembly and Kettle Lid Stirrer Wand and Stirrer Collar Scoop and (2) Ladles

SETUP

Setup the appliance only on a firm, level, non-combustible surface. Verify local codes for requirements. Concrete, tile, terrazzo or metal surfaces are recommended. Metal over combustible material may not meet code for non-combustible surfaces.

Verify that the unit sits firmly ON ALL FOUR LEGS. With a spirit level, check that the appliance is level front-to-back and side-to-side. With the adjustable legs, adjust as required to level the appliance. All four legs must be adjusted to firmly contact the floor in order to prevent tipping.

Avoid storing flammable or combustible materials in, on or near the appliance.

ASSEMBLY

Slide kettle lid over stirrer shaft and lid guide. The handle should be toward the door opening. Slide the lid up until it is captured by the magnetic holder.

Slide the stirrer collar over the stirrer shaft. Thread the stirrer wand through the slot in the shaft, then allow the collar to drop into place.

Position kettle vertically with the knob down and to the right side. Attach kettle to the two hangers. Allow kettle to rotate horizontal. Connect the kettle electrical pigtail to the twist-lock receptacle.

Thread the heat lamp into the heat lamp socket. Install the heat lamp guard.

Install the drop door and crumb tray.

232 306223 Owners Manual WPP-Series Popcorn Popper

WPP-10, WPP-6, WPP-10 specifications

The Wells WPP-6 and WPP-10 are sophisticated water purification systems designed for both domestic and industrial applications. Their primary objective is to provide clean, safe, and potable water, utilizing advanced technologies and efficient design.

Starting with the Wells WPP-6, this model is renowned for its compact design, making it an ideal choice for households and small businesses. It features a multi-stage filtration system that incorporates sediment filters, activated carbon filters, and reverse osmosis membranes. This tiered approach ensures that both larger particles and smaller contaminants are effectively removed from the water. The WPP-6 is equipped with a UV sterilization component that serves to eliminate biological contaminants, further ensuring water safety. Its energy-efficient operation and low maintenance requirements make the WPP-6 a popular choice among users seeking reliable water purification solutions.

On the other hand, the WPP-10 model scales up the capabilities of the WPP-6, targeting larger households or light commercial enterprises. With a higher water output, the WPP-10 utilizes similar multi-stage filtration technology but is designed for increased capacity. It features an enhanced reverse osmosis system that offers a higher recovery rate, thereby minimizing water waste—a critical attribute in today's environmentally conscious market. The WPP-10 is also equipped with smart monitoring systems that allow users to track water quality and filter status, providing real-time data to ensure optimal performance.

In terms of technological advancements, both models employ quick-connect fittings for easy installation and filter replacement. This user-friendly feature drastically reduces the time and effort required for maintenance, making them accessible for non-specialists. Additionally, these systems are typically constructed with food-grade materials, which enhances their durability and ensures that the water quality is not compromised by harmful substances.

In conclusion, the Wells WPP-6 and WPP-10 stand out in the realm of water purification systems, offering robust features and technologies that prioritize safety and efficiency. Their respective designs cater to various user needs, ensuring clean drinking water is accessible in both residential and light commercial settings. With their reliable operation and advanced design features, they represent a significant investment in health and well-being. Whether for home use or small businesses, these systems exemplify the importance of effective water purification technology in maintaining high standards of water quality.