DeLonghi ECAM26455M manual Technical Specification, Removing the filter

Please note

The filter lasts about two months if the appliance is used normally. If the coffee maker is left unused with the filter installed, it will last a maximum of three weeks.

3. Remove the tank from the appliance and fill with water.

4.Insert the filter in the water tank and immerse it completely for ten or so seconds, sloping it to enable the air bubbles to escape (fig. 34).

5.Insert the filter in the filter housing (fig. 35A) and press as far as it will go.

6.Close the tank with the lid (fig. 35B), then replace the tank in the machine.

When you install the filter, you must notify the appliance of its presence.

7.Press the MENU/ESC button to enter the menu;

8.Press the MILK or

	CAPPUCCINO				button		33
	(fig. 8)		until		“Install
	filter” is displayed;
9.	Press	the
	button;
10.	The message “Enable?” is
	displayed.
11.	Press	the
	button	to	confirm			the
	selection.		“Hot		water
	Confirm?” is displayed.
12.	Position a container with
	a minimum capacity of						34
	3.4 oz / 100 ml under the
	hot water spout.
13.	Press	the
	button	to	confirm			the
	selection. The appliance
	begins	delivering				hot
	water and the message
	“Please		wait		“	is
	displayed.						35A
14.	After	delivery,				the
	appliance				returns
	automatically			to		the
	“Ready		for		coffee”
	position.
The new filter is active.You can							35B
now use the coffee maker.
Replacing the filter
When “REPLACE				FILTER” is

displayed, after two months (see date indicator) or when

the appliance has not been used for 3 weeks, you should replace the filter:

1.Remove the exhausted filter;

2.Remove the new filter from the packaging.

3.Turn the date indicator disk (see fig. 33) until the next 2 months of use are displayed (the filter lasts about two months);

4.Refill the tank;

5.Insert the filter in the water tank and immerse it completely, tilting it to enable the air bubbles to escape (fig. 34);

6.Place the filter in the filter housing (fig. 35aa) and press as far as it will go. close the tank with the lid (fig. 35b), then replace the tank in the machine;

7.Position a container with a minimum capacity of 3.4 oz / 100 ml under the hot water spout.

8.Press the MENU/ESC button to enter the menu;

9.Press the MILK or CAPPUCCINO button until “Reset filter “ is displayed.

10.Press the button;

11.The message “Confirm?” is displayed.

12.	Press the	button to confirm the selection;
13.	“Hot water, Press OK” is displayed.
14.	Press the	button to confirm the selection. the
	appliance begins delivering hot water and the message
	“Please wait “ is displayed.

15.After delivery, the appliance returns automatically to the “ready for coffee” position.

The new filter is now active and you can use the coffee maker.

Removing the filter

If you want to continue using the appliance without a filter, you must remove it and notify the appliance of its removal as follows:

1.Extract the tank and exhausted filter;

2.Press the MENU/ESC button to enter the menu;

3.Press the MILK or CAPPUCCINO button (fig. 8) until “Install filter Enabled” is displayed;

4.Press the button

5.“Disable?” is displayed;

6.Press the button to confirm and the MENU/ESC button to exit the menu.

TECHNICAL SPECIFICATION

	Voltage:		120V~60 Hz
	Absorbed power:		1250W
	Pressure:		15 bar
	Water tank capacity:		67.62 fl. oz. / 2.0 liters max.
	Size Lxhxd:	9.3x13.8x17.5 in / 238x350x445 mm
	Cable length:		2,92 ft / 1.80 m
	Weight:		260 lb / 11.8 kg
19	Beans container capacity:		8.82 oz / 250 g max.