DeLonghi ECAM26455 Cup warmer, Setting water hardness, Setting the language, Install filter, Beep

“Enable?”if the function has been disabled);o

4. Press the	button to disable (or enable) energy
saving mode;

5.Then press the MENU/ESC button to exit the menu.

When the function is enabled, if the machine is not used for about 1 minute, “Energy Saving”is displayed.

Please note!

When in energy saving mode, a few seconds may elapse before the first drink with milk is delivered as the appliance must heat up again.

Cup warmer

This function enables or disables the cup warmer. Proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the HOT MILK or LATTE button (fig. 8) until “Cup

	warmer”appears on the display;
3.	Press the	button. “Disable?” is displayed (or
	“Enable?”if the function has been disabled);
4.	Press the	button to disable (or enable) the
	function.

5.Press the MENU/ESC button to exit the menu. Warming the cups keeps the coffee hot.

Setting water hardness

For instructions on setting water hardness, see page 17.

Setting the language

To change the language for the display, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the HOT MILK or LATTE button (fig. 8) until “Set language”is displayed;

3.Press the button;

4.Press the HOT MILK or LATTE button until the required language is displayed;

5.	Press the	button to confirm;
6.	Press the MENU/ESC button to exit the menu.

Install filter

For instructions on how to install the filter, see the section “Installing the filter”on page 18.

Replacing the filter

For instructions on how to replace the filter, see the section “Replacing the filter”on page 19.

Beep

This enables or disables the beep emitted by the machine each time the buttons are pressed or an accessory is inserted/ removed. The beep is enabled by default.

To disable or re-enable the beep, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the HOT MILK or LATTE button (fig. 8) until “Beep” is displayed;

3.	Press the	button. “ Disable?” or “ Enable?” is
	displayed;
4.	Press the	button to enable or disable the beep;
5.	Press the MENU/ESC button to exit the menu.

Cup lighting

This function enables or disables the cup lighting. The lighting is enabled by default.

The lights come on each time coffee and drinks with milk are made and during each rinse cycle.

To disable or re-enable this function, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the HOT MILK or LATTE button (fig. 8) until “Cup

	lighting”is displayed.
3.	Press the	button. “ Disable?” or “ Enable?” is
	displayed;
4.	Press the	button to enable or disable the cup
	lighting;
5.	Press the MENU/ESC button to exit the menu.

Default values (reset)

This resets all menu settings and programmed quantities back to the default values (with the exception of the language which remains as previously set).

To reset the default values, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the HOT MILK or LATTE button (fig. 8) until“Default values”is displayed;

3.Press the ; button

4.The message “Confirm?”is displayed.

5.Press the button to confirm and exit.

Statistics function

This displays statistics relating to the machine.

To display, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the HOT MILK or LATTE button (fig. 8) until “Statistics”is displayed;

3.Press the button;

4.Press the HOT MILK or LATTE button (fig. 8) to verify:

-how many coffees have been made;

-how many times the machine has been descaled;

-the total number of litres of water delivered;

-the total number of drinks made with milk;

-how many times the water filter has been replaced.

5. Press the MENU/ESC button twice to exit the menu.

11