Maytag ERV-210, HRV-210, HRV-150, ERV-150 manual To Order Parts Contact your local distributor

Page 5

1.0

Service

(cont’d)

1.2PARTS ORDERING CHART

	No	Description	150	150	210	210
	No	Description	HRV	ERV	HRV	ERV
			HRV	ERV	HRV	ERV
	1	Double collar port #2	00866	00866	00866	00866
	2	Wing nut #10-32	00874	00874	00874	00874
	3	Balancing double collar port	02256	02256	02256	02256
	4	Inlet ring	12913	12913	12913	12913
	5	Motor assembly	13504	13555	13556	13506
	6	Electronic board V99	13507	13507	13507	13507
	7	Square balancing damper	12645	12645	12645	12645
	8	Door latches (latch)	00886	00886	00886	00886
	9	Drain connector	02418	02418	02418	02418
	10	Drain gasket 0.625”DI	02419	02419	02419	02419
	11	Washer 5/8” ID x 1” OD	03117	03117	03117	03117
	12	Nut 5/8-18	02420	02420	02420	02420
	13	Recovery core	03132	03136	03133	03137
	14	Door assembly	15770	15770	15770	15770
	15	Door latches (keeper)	00887	00887	00887	00887
	16	Hinge assembly	00672	00672	00672	00672
	17	Filter	03096	03096	03097	03097
	18	Switch E69 10A	01825	01825	01825	01825
	19	Damper assembly #2	12643	12643	12649	12649
	20	Plastic balancing damper	02253	02253	02253	02253
	21	Damper rod	12620	12620	12620	12620
	22	Double collar port #5	02021	02021	02021	02021
	23	Damper #1	12459	12459	12459	12459
	24	Damper actuator assembly	03124	03124	03124	03124
	25	Electronic box cover	13046	13046	13046	13046
	26*	Thermistor kit	12895	12895	12895	12895

* Item 26 not shown.

Please take note that parts not listed are not available; those parts require assembly knowledge that only manufacturer can guarantee.

TO ORDER PARTS: Contact your local distributor

1.3 Technical Support (for assistance)

For assistance, call on week days, 8:00 AM to 4:30 PM (Cental Standard Time).

Technical Support Department

tel: 1-866-2MAYTAG

5

Image 5

Contents Ventilation Systems Installer Manual Table of Contents Nstallation of the C Ontrols About this ManualService To Order Parts Contact your local distributor High speed SizingHRV ERV-210 Technical DataModel Number ERV-150 Model Number HRV-150 Model numbers ERV-150, HRV-150 ERV-210, HRV-210 Fully Ducted System Typical InstallationInspect the Contents of the BOX InstallationCalculating the Duct Size Installation cont’dPlanning of the Ductwork Calculating the Duct Size CONT’D Installing the Ductwork and RegistersInstalling the Ductwork and Registers cont’d Method 2 return-return Method 1 return-supplyInsulated flexible duct Connecting Ducts to the UnitRigid duct Do not use screws to connect rigid ducts to the portsConnecting the Drain Installing the Exterior HoodsExhaust Hood 152 mm Intake Hood 18 457 mm Optional ductAll models require a main control Control DevicesOptional Control Special Cold Weather TBI Mode for Ervs Other FeaturesCharacteristics of cold weather TBI mode Main and Optional Controls Available for Your UnitDimensions and Specifications Main Controls Installation of the ControlsInstallation of the Main Control Never install more than one main control per unitInstallation of the Main Control cont’d Electrical Connection to the Furnace Electrical Connection to Optional ControlsDiagram WiringAir Flow Balancing If you are using Flow CollarsIf you are using Flow Measuring Stations Balancing Procedure Main Controls 11.0 Overall VerificationDo not oil the motor. It is already permanently lubricated Maintenance / Instructions for UserStart-up troubleshooting TroubleshootingLight does not stay on References Warranty