Maytag HRV-210, ERV-210, HRV-150, ERV-150 manual Installing the Ductwork and Registers cont’d

Page 16

6.0

Installation(cont’d)

6.5Installing the Ductwork and Registers (cont’d)

6.5.2Exhaust Ducted System (Source Point Ventilation) (as illustrated in Section 5.2) Stale air exhaust ductwork: (same as for Fully Ducted System, described on page 15)

Fresh air distribution:

010! WARNING

When performing duct connection to the furnace, installation must be done in accordance with all applicable codes and standards. Please refer to your local building code.

CAUTION

When performing connection to the furnace supply duct, this duct must be sized to support the additional airflow produced by the HRV/ERV. Also, use a steel duct with a backdraft damper to pre- vent the risk of overheating the HRV/ERV.

There are two methods for connecting the unit to the furnace:

Method 1: supply side connection

•Cut an opening into the furnace supply duct at least 18 inches (0.5 m) from the furnace.

•Connect this opening to the fresh air distribution port of the HRV/ERV (use steel duct, see figure 10).

•Make sure that the HRV/ERV duct forms an elbow inside the furnace ductwork.

•If desired, interlock (synchronize) the furnace blower operation with the HRV/ERV operation.

(See Section 8.4).

Steel duct with backdraft damper

VD0040

figure 10

minimum 18” (0.5 m)

Method 2: return side connection

•Cut an opening into the furnace return duct not less than 10 feet (3.1 m) from the furnace (A+B).

•Connect this opening to the fresh air distribution port of the HRV/ERV (see figure 11).

NOTE: For Method 2, it is not essential that the furnace blower runs when the HRV/ERV is in operation,

but we recommend it. If desired, synchronize the VD0041 furnace blower operation (see Section 8.4).

A

B

A+B= not less than 10’ (3.1 m)

figure 11

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Installer Manual Ventilation SystemsTable of Contents About this Manual Nstallation of the C OntrolsService To Order Parts Contact your local distributor Sizing High speedHRV Technical Data ERV-210Model Number ERV-150 Model Number HRV-150 Model numbers ERV-150, HRV-150 ERV-210, HRV-210 Typical Installation Fully Ducted SystemInstallation Inspect the Contents of the BOXPlanning of the Ductwork Installation cont’dCalculating the Duct Size Installing the Ductwork and Registers Calculating the Duct Size CONT’DInstalling the Ductwork and Registers cont’d Method 1 return-supply Method 2 return-returnConnecting Ducts to the Unit Insulated flexible ductRigid duct Do not use screws to connect rigid ducts to the portsInstalling the Exterior Hoods Connecting the DrainExhaust Hood 152 mm Intake Hood 18 457 mm Optional ductOptional Control Control DevicesAll models require a main control Other Features Special Cold Weather TBI Mode for ErvsCharacteristics of cold weather TBI mode Main and Optional Controls Available for Your UnitInstallation of the Controls Dimensions and Specifications Main ControlsInstallation of the Main Control Never install more than one main control per unitInstallation of the Main Control cont’d Electrical Connection to Optional Controls Electrical Connection to the FurnaceWiring DiagramIf you are using Flow Measuring Stations If you are using Flow CollarsAir Flow Balancing Balancing Procedure 11.0 Overall Verification Main ControlsMaintenance / Instructions for User Do not oil the motor. It is already permanently lubricatedTroubleshooting Start-up troubleshootingLight does not stay on Warranty References

ERV-150, HRV-150, ERV-210, HRV-210 specifications

The Maytag HRV-210, ERV-210, HRV-150, and ERV-150 are advanced heat recovery and energy recovery ventilators designed to enhance indoor air quality while promoting energy efficiency in residential settings. Each model comes packed with features tailored to balance ventilation and energy conservation, making them suitable for a variety of home environments.

The HRV-210 and HRV-150 are heat recovery ventilators that excel in transferring heat from outgoing stale air to incoming fresh air. This process effectively maintains comfortable indoor temperatures, recovering up to 70% of the heat energy, which can lead to significant energy savings during colder months. Both models boast an airflow capacity of up to 210 CFM and 150 CFM, respectively, ensuring effective ventilation for medium to large-sized homes.

On the other hand, the ERV-210 and ERV-150 embody energy recovery technology that captures not only heat but also moisture content from the air. This is particularly beneficial in humid climates where maintaining humidity levels is crucial for comfort and health. With similar airflow capacities as the HRV models, these ERVs help regulate humidity levels, preventing the growth of mold and improving indoor air quality.

All four models are equipped with energy-efficient motors designed for quiet operation, ensuring that users experience minimal noise disruption while enjoying fresh air. The inclusion of user-friendly controls and adjustable settings allows homeowners to customize their ventilation strategy according to seasonal changes or personal preferences.

Another important characteristic of the Maytag ventilators is their durable build and ease of installation. With a design that promotes straightforward maintenance, the filters can be easily accessed and cleaned or replaced, extending the life of the unit and maintaining optimal performance over time.

In addition to their functional benefits, all models adhere to industry standards for energy efficiency, contributing to sustainable living practices. The Maytag HRV-210, ERV-210, HRV-150, and ERV-150 are comprehensive solutions for homeowners looking to enhance indoor air quality while optimizing energy consumption, making them a smart investment for modern living. Each model combines innovative technologies with practical features, making them a standout choice in the realm of home ventilation systems.
Top Page Image Contents