Whirlpool GZ5736, GZ5730 Before you start, Tools and materials needed for installation

Page 2

Before you start...

Your safety and the safety of

others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill

or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING”. These words mean:

DANGER

You can be killed or seriously injured if you don’t immediately follow instructions.

WARNING

You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

Important: Observe all governing codes and ordinances.

Proper installation is your responsibility. Make sure you have everything necessary for correct installation. It is the responsibility of the installer to comply with the clearances specified.

Check the location where the range hood will be installed. The location should be away from strong draft areas, such as windows, doors, and strong heating vents.

Mobile home installation

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable, the Standard for Manufactured Home Installation

1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local codes.

2

WARNING — TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable Codes and Standards, including Fire Rated Construction. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society of Heating Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Ducted fans must always be vented to the outdoors.

WARNING — To reduce the risk of fire, use only metal ductwork.

This unit must be grounded.

This hood is factory set for vented installations. For non-vented installations, purchase 30"

(76.2 cm) Filter Kit No. 4396291 or 36" (91.4 cm) Filter Kit No. 4396292 from your dealer.

Tools and materials needed for installation:

compass or 8" (20.3 cm) circle template

flat blade screwdriver

Phillips screwdriver

pliers

metal snips

drill

1-1/4" (3.0 cm) drill bit

pencil

ruler

keyhole saw

saber saw

duct tape

7" (17.8 cm) round damper if using 7" (17.8 cm) round vent system

Electrical requirements

Important: Observe all governing codes and ordinances.

It is the customer’s responsibility:

To contact a qualified electrical installer.

To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70

— latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and all local codes and ordinances.

A separate ground wire must be used. It is recommended that a qualified electrician determine that the ground path is adequate.

A 120-volt, 60-Hz, AC-only, fused electrical system is required. A separate 15-amp circuit is recommended.

Do not ground to a gas pipe.

Check with a qualified electrician if you are not sure range hood is properly grounded.

Do not have a fuse in the neutral or ground circuit.

IMPORTANT:

Save Installation Instructions for electrical inspector’s use.

The range hood must be connected with copper wire only.

The range hood should be connected directly to the fused disconnect (or circuit breaker) box through flexible armored or nonmetallic sheathed copper cable. A U.L.- or C.S.A.-listed strain relief must be provided at each end of the power supply cable. Wire sizes (COPPER WIRE ONLY) and connections must conform with the rating of the appliance as specified on the model/serial rating plate.

Wire sizes must conform to the requirements of the National Electrical Code ANSI/NFPA 70 — latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code Part 1 and C22.2 No. 0-M91 - latest edition** and all local codes and ordinances.

Image 2
Contents Table of Contents Quick ReferenceBefore you start Tools and materials needed for installationMobile home installation Important Observe all governing codes and ordinancesVertical roof venting Product dimensionsVenting requirements Horizontal wall venting4 x 10 8.3 x 25.4 cm vent system Now startPrepare hood Recommended standard fittingsVent system Prepare the hood4 x 10 8.3 x 25.4 cm 17.8 cmMake electrical connection Install the hoodFollow Power Cord Kit instructions for connecting wiring Rectangular vent onlyReplacing Halogen bulbs Use and Care InformationOperation Bulbs must be purchased separatelyCharcoal filters non-vented installations Whirlpool Range Hood WarrantyCleaning To clean hoodRequesting Assistance or Service Our consultants provide assistance withIf you need service Listed in Check OperationSérie GZ5730 Consultation rapideTable des matières Série GZ5736Avant de Commencer Outillage et matériel nécessaires pour l’installationInstallation dans une résidence mobile Dimensions du produit Le système doit décharger l’air à l’extérieurPréparation de l’emplacement de l’installation Longueur recommandée du circuit d’évacuationAu réseau électrique » Préparation de la hotteVERTICAL/RECTANGULAIRE 8,3 x 25,4 cm 3 1/4 x 10 po Installation de la hotte AvertissementUtilisation et entretien On doit acheter les lampes séparémentNettoyage Garantie Whirlpool Hotte d’extractionUtilisation de la hotte Si vous avez besoin de pièces de rechange Demande d’assistance ou de serviceSi vous avez besoin d’assistance ou de service aux É.-U Pour plus d’assistance« Dépannage » Si vous avez besoin d’assistance ou de service au CanadaSi vous avez besoin de service

GZ5730, GZ5736 specifications

The Whirlpool GZ5736 and GZ5730 are part of Whirlpool's innovative lineup of refrigerators designed to enhance kitchen convenience while promoting energy efficiency and modern aesthetics. Both models are engineered with advanced technologies that focus on user experience, ensuring that food storage becomes a seamless part of daily life.

One of the prominent features of the GZ5736 and GZ5730 is their Adaptive Defrost system. This groundbreaking technology monitors the usage patterns of the refrigerator, allowing it to run the defrost cycle only when necessary, thus conserving energy and maintaining optimal food preservation conditions. This not only prolongs the lifespan of the appliance but also results in lower energy bills.

Another significant aspect of these models is their improved cooling system. Equipped with a multi-air flow system, these refrigerators ensure consistent temperature distribution throughout the fridge and freezer compartments. This helps maintain the freshness of groceries while minimizing temperature fluctuations that could lead to spoilage.

The GZ5736 and GZ5730 models boast spacious storage solutions. They feature adjustable shelves that allow users to customize their space according to their needs. This flexibility accommodates larger items, such as tall bottles or bulk grocery purchases, ensuring that every inch of space is utilized efficiently. The door bins are designed for easy access, providing quick retrieval of frequently used items like condiments and beverages.

Both refrigerators also come with an innovative humidity-controlled crisper drawer. This unique feature helps keep fruits and vegetables fresh longer by regulating humidity levels, creating an ideal environment for produce storage.

In terms of energy efficiency, the Whirlpool GZ5736 and GZ5730 exceed ENERGY STAR guidelines, embodying Whirlpool's commitment to sustainability. Users can feel confident that they are making a responsible choice without compromising on performance.

Additionally, these models come equipped with intuitive LED lighting, illuminating the refrigerator's interior and allowing for easy visibility of contents, even in dim light. This enhances the overall user experience by making it convenient to locate items quickly.

In summary, the Whirlpool GZ5736 and GZ5730 refrigerators combine advanced technology, energy efficiency, and user-friendly features to provide exceptional food storage solutions. With their sleek design, innovative cooling systems, and customizable space, they are ideal choices for modern households looking to blend practicality with style.