Whirlpool GZ5736, GZ5730 Install the hood, Make electrical connection, Rectangular vent only

Page 6

up to 1” (2.5 cm) side-to-side

adjustmenttop/back edge

damper/vent connector

pivot

VERTICAL

pivot

vent position

HORIZONTAL vent position

11.Rectangular vent only:

Attach damper/vent connector over knockout opening. Make sure damper pivot is nearest to top/back edge of hood. Remove tape from damper flap.

Note: For horizontal vent systems, it is recommended that the rectangular ventwork be attached to the damper/vent connector and sealed with duct tape before installing the hood.

12.Round vent only: Re-install round vent plate removed in Step 5 under “Prepare the hood” section. Install a 7" (17.8 cm) round damper (must be purchased separately). Damper flap must open freely in direction of air flow (away from range hood).

Note: Damper/vent connector and round vent plate can be installed up to 1" (2.5 cm) on either side of hood center if ventwork is off- center. In extreme off-center installations, one end of the vent connector may need to be trimmed to clear the electrical strain relief.

Make electrical connection

WARNING

Electrical Shock Hazard

Disconnect power before making electrical connections.

Connect ground wire to green ground screw in terminal box.

Failure to do so can result in death or electrical shock.

Do not turn on power until installation is complete. If not

previously done, run wiring through wall or cabinets according to electrical codes and ordinances.

protective cover

13.Stand hood up as shown. (Keep on protective cover to protect hood or cooking surface.)

green ground

screw

14.Connect the white and black wires of the power supply cable to the white and black leads in the hood with twist-on connectors. Connect the power supply ground wire to the green screw under the wiring cover.

Securely tighten the strain relief.

Using a U.L.-listed power supply cord-connection kit (U.S. only):

Follow Power Cord Kit instructions for connecting wiring.

15.Replace wiring cover.

Install the hood

WARNING

Excessive Weight Hazard

Use two or more people to move and install range hood.

Failure to do so can result in back or other injury.

1/4"

(6.4 mm)

16.Remove the 4 hood mounting screws from the parts bag and install in pilot holes. Leave screw heads away from shim strips about 1/4" (6.4 cm).

keyhole slots (4)

mounting screw

keyhole slots (4)

17. Lift range hood into final position, feeding electrical wire through wiring opening. To avoid damage, DO NOT PUSH ON FAN BLADE.

Position the range hood so that the large end of the keyhole slots are over the screws. Then push the hood toward the wall so that the screws are in the neck of the slots. Tighten mounting screws to cabinet, making sure mounting screws are in narrow neck of slots. Make sure that damper blade opens and closes freely.

18.Connect ventwork to hood. Seal joints with duct tape to make them secure and air tight.

6

Image 6
Contents Table of Contents Quick ReferenceBefore you start Tools and materials needed for installationMobile home installation Important Observe all governing codes and ordinancesVertical roof venting Product dimensionsVenting requirements Horizontal wall venting4 x 10 8.3 x 25.4 cm vent system Now startPrepare hood Recommended standard fittingsVent system Prepare the hood4 x 10 8.3 x 25.4 cm 17.8 cmMake electrical connection Install the hoodFollow Power Cord Kit instructions for connecting wiring Rectangular vent onlyReplacing Halogen bulbs Use and Care InformationOperation Bulbs must be purchased separatelyCharcoal filters non-vented installations Whirlpool Range Hood WarrantyCleaning To clean hoodRequesting Assistance or Service Our consultants provide assistance withIf you need service Listed in Check OperationSérie GZ5730 Consultation rapideTable des matières Série GZ5736Outillage et matériel nécessaires pour l’installation Installation dans une résidence mobileAvant de Commencer Dimensions du produit Le système doit décharger l’air à l’extérieurPréparation de l’emplacement de l’installation Longueur recommandée du circuit d’évacuationPréparation de la hotte VERTICAL/RECTANGULAIRE 8,3 x 25,4 cm 3 1/4 x 10 poAu réseau électrique » Installation de la hotte AvertissementUtilisation et entretien On doit acheter les lampes séparémentGarantie Whirlpool Hotte d’extraction Utilisation de la hotteNettoyage Si vous avez besoin de pièces de rechange Demande d’assistance ou de serviceSi vous avez besoin d’assistance ou de service aux É.-U Pour plus d’assistanceSi vous avez besoin d’assistance ou de service au Canada Si vous avez besoin de service« Dépannage »

GZ5730, GZ5736 specifications

The Whirlpool GZ5736 and GZ5730 are part of Whirlpool's innovative lineup of refrigerators designed to enhance kitchen convenience while promoting energy efficiency and modern aesthetics. Both models are engineered with advanced technologies that focus on user experience, ensuring that food storage becomes a seamless part of daily life.

One of the prominent features of the GZ5736 and GZ5730 is their Adaptive Defrost system. This groundbreaking technology monitors the usage patterns of the refrigerator, allowing it to run the defrost cycle only when necessary, thus conserving energy and maintaining optimal food preservation conditions. This not only prolongs the lifespan of the appliance but also results in lower energy bills.

Another significant aspect of these models is their improved cooling system. Equipped with a multi-air flow system, these refrigerators ensure consistent temperature distribution throughout the fridge and freezer compartments. This helps maintain the freshness of groceries while minimizing temperature fluctuations that could lead to spoilage.

The GZ5736 and GZ5730 models boast spacious storage solutions. They feature adjustable shelves that allow users to customize their space according to their needs. This flexibility accommodates larger items, such as tall bottles or bulk grocery purchases, ensuring that every inch of space is utilized efficiently. The door bins are designed for easy access, providing quick retrieval of frequently used items like condiments and beverages.

Both refrigerators also come with an innovative humidity-controlled crisper drawer. This unique feature helps keep fruits and vegetables fresh longer by regulating humidity levels, creating an ideal environment for produce storage.

In terms of energy efficiency, the Whirlpool GZ5736 and GZ5730 exceed ENERGY STAR guidelines, embodying Whirlpool's commitment to sustainability. Users can feel confident that they are making a responsible choice without compromising on performance.

Additionally, these models come equipped with intuitive LED lighting, illuminating the refrigerator's interior and allowing for easy visibility of contents, even in dim light. This enhances the overall user experience by making it convenient to locate items quickly.

In summary, the Whirlpool GZ5736 and GZ5730 refrigerators combine advanced technology, energy efficiency, and user-friendly features to provide exceptional food storage solutions. With their sleek design, innovative cooling systems, and customizable space, they are ideal choices for modern households looking to blend practicality with style.