Xantech MRAUDIO8X8M, MRC88M installation instructions MRC88m Keypad mounting template

Page 23

Model MRC88m / MRAUDIO8x8m

Page: 23

b.Using a level, make proper horizontal and vertical marks on surface to be cut, to properly orient template.

Figure 7 – MRC88m Keypad mounting template

c. Locate the provided template so that the mark is in the center of the hole, which is in the center of the template.

d. Rotate the template around the center until the template is level.

e. Press or hammer the template in place so that the holding tabs pierce the wall and hold the template in place.

f. Mark or scribe the outline of the template on the wall.

g. Remove the template and cut a clean hole through the wall along the outline of the template, being sure that your cut is on the outline. Any cut outside of the outline by more than ¼” may not be covered by the MRC88m Keypad.

1 2

Figure 8 – Installing the MRC88m Keypad mounting bracket in the wall

2.Installing the Mounting Bracket

a.Attach the ground wire to the ground lug to the rear of the back-bar with the provided green nut, before beginning the bracket installation process.

NOTE: A ground wire connected to Earth ground is required to protect against static discharge.

b.Orient the Mounting Bracket so the ground lug is on the top portion of the bracket and run the supplied screws through the top front of the mounting bracket into the back-bar as shown in Figure 6.

Note: Do not tighten screws.

c.Pull the CAT5 cable through the hole in the wall.

d.Pull the CAT5 cable through the hole in the mounting bracket.

© 2009 Xantech Corporation

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model MRC88m Model MRAUDIO8x8m Not Expose this Appliance to Rain or Moisture Safety Instructions Read Before Operating EquipmentTable of Contents Programming the Controller ADVANCED/EXPANDED Programming Tweaking the System Model MRC88m / MRAUDIO8x8m Xantech Corporation MRC88m system includes the following components General InformationModel MRC88m / MRAUDIO8x8m System Overview System Block DiagramCONTROLLER/AMPLIFIER Features Keypad Features Front Panel MRC88M Front Panel Features and ConnectionsSystem Status Power-Up Mode Zone Status Active-Operational Mode Source Component Input Connections MRC88M Rear Panel Features and ConnectionsSource Loop-Thru Connections MRC88m Keypad MRC88M Keypad Front FeaturesModel MRC88m / MRAUDIO8x8m MRC88M Keypad Rear Features and Connections Model MRC88m Keypad Rear Panel Features and FunctionsOperation OUT-OF-THE-BOX PRE Test BASIC/ADVANCED/EXPANDED InstallationMRC88 Expanded Mounting and Installing the MRC88m KeypadMRC88m Keypad mounting template MRC88M Keypad Removal Optional Keypad Back-Box for pre-install applicationsVideo Connections MRC88m Only Audio ConnectionsBASIC/ADVANCED Advanced CSM1 Threshold AdjustmentsBASIC/ADVANCED/EXPANDED Zone Related Wiring ConnectionsStatus BASIC/ADVANCED/EXPANDED Composite VideoModulated Video Zone IR BASIC/ADVANCED/EXPANDED Control OutCO1 and CO2 Zones 7 OFF Connections AT the Zone Location BASIC/ADVANCED/EXPANDEDZone IR Zone Expansion Connecting TWO MRC88M Controllers ExpandedMRC88m Keypad CAT5 Cable Lengths MRC88m Connecting Block located on rear of KeypadVideo Connections SETTING-UP the MRC88m System Pre-Programming the MRC88m BASIC/ADVANCED/EXPANDED Computer Requirements Minimum Basic Mode Advanced Mode Expanded ModePlanning the System Starting MRC88M Dragon DROP-IR Software Connecting the MRC88M CONTROLLER/AMPLIFIER to the PCSoftware Installation Included Hardware & Software ItemsStarting a Project BUILT-IN IR Code Library BASIC/ADVANCED/EXPANDED Learning IR Commands Creating Palette FilesLearning IR Commands BASIC/ADVANCED/EXPANDED Built-In Mfg’s IR Command LibraryRecording Toggle Command Functions Creating a Palette File BASIC/ADVANCED/EXPANDED To Rename an Existing FunctionTo Add a New Function Importing CCF Files Getting Source Commands from the InternetEditing BRAND, COMPONENT, and Function Lists Importing Discrete IR Hex Codes ADVANCED/EXPANDED Entering RS232 Command StringsRS232 Palette Editor Window Using PC TestUsing MRC88m Test Creating an RS232 Palette File Creating AN RS232 Palette File ADVANCED/EXPANDEDProgramming The Controller Downloading Source Icons to the Keypad Creating NEW IconsSelecting Icons from the Icon Generator Placing Commands on the Virtual Keypad Basic Placing Commands Onto the Virtual KeypadSelecting RS232 Command Palettes ADVANCED/EXPANDED Selecting Internal Amplifier Commands ADVANCED/EXPANDEDProgramming Sequences Macros Editing Buttons on the Virtual Keypad Button Edit Pop-Up MenuEditing Commands in the Macro Command List Window Zone 1 thru Editing CommandsProgramming Power Management Programming Power Management and Sense Trigger CodesBasic Power Management Programming Sense Triggers Programming Sense Trigger Codes ADVANCED/EXPANDEDTesting Commands Under Power Management and Sense Triggers RC68 Code Group Zone Options ConfigurationDefault settings set in Basic Mode are as follows Name of Zone ADVANCED/EXPANDEDIR Loop Back Settings ADVANCED/EXPANDED PRE AMP Volume Adjust Settings ADVANCED/EXPANDEDTransferring the Project Configuring Commands for IR in ZoneZone Audio Input Controller Options ProgrammingExpanded Options Mode of OperationIR Routing BACK-LIGHT ControlMonitor Lockout Mode Factory default Disabled RS232 SettingsMonitor Lockout Mode Zone Linking Programming Dynamic Zone Link Mode Factory default Disabled Clear ALL RS232 Input TranslatorLink ALL Dynamic Link ALL StaticIRS232 Input Translator Programming IR Commands and SequencesRC68+ IR Code Triggered Sequencer RC68 IR Command Macro WindowInternal Amplifier Command Window Programming Internal Amplifier CommandsUsing Internal Amplifier Commands Internal Amplifier Commands Zone Expansion Connecting Multiple MRC88M ControllersPhysical Connections in Expanded Mode Programming in Expanded ModeEnabling Expanded Mode RS232 Control While in Expanded Mode Sources 1 through Completing the Programming Process Saving and BACKING-UP Files Downloading Firmware Files from the WEB Firmware Upgrade OptionsWarm Firmware Upgrade Cold Firmware UpgradeTweaking the System Trimming Source Audio Input Levels Making Fine AdjustmentsKeypad Adjustments Zone AdjustmentsSource Slection and Control Powering the Zone on and OFFSetting the Volume Accessing Tier 2 CommandsDynamic Monitor Lockout Parental Control ADVANCED/EXPANDED Zone SettingsAudio Adjustments BASIC/ADVANCED/EXPANDED System Status BASIC/ADVANCEDExpanded RS232 Control ?5SS3+ 7PR1+?5SS+ AO+ Commands?z#PR+ QueriesVolume Level 39 Steps Keypad Button ID MRC88m Setting Level in dB +14 +12 +10 Balance Level MRC88m Left Speaker Right Speaker Attenuation SettingProblem Probable Cause and Solution TroubleshootingModel MRC88m / MRAUDIO8x8mPage 96Model MRC88m / MRAUDIO8x8m Problem Probable Cause and Solution RS232 and Expansion PIN OUT Information IR Sensor SpecificationsCertifications VideoModel MRC88m / MRAUDIO8x8m Model MRC88m / MRAUDIO8x8m Xantech Corporation Xantech Corporation
Related manuals
Manual 7 pages 32.14 Kb Manual 10 pages 43.55 Kb Manual 12 pages 31.84 Kb

MRAUDIO8X8M, MRC88M specifications

The Xantech MRC88M is a sophisticated multi-room audio system that seamlessly integrates into modern home environments, offering unparalleled control and quality of sound distribution. Designed for audiophiles and casual listeners alike, this powerful system enables users to enjoy their favorite music, podcasts, and audio from multiple sources throughout their home.

One of the standout features of the MRC88M is its 8-zone capability, allowing users to create and control up to eight independent audio zones. Each zone can customize its volume, source selection, and audio settings, providing a highly personalized audio experience. This flexibility means that different rooms can enjoy varied audio at the same time, making it ideal for entertaining guests or relaxing in private spaces.

The MRC88M employs advanced technologies to ensure high-quality sound reproduction. It uses a reliable audio matrix router that allows for the precise routing of audio signals between connected sources and zones. This ensures minimal interference and maximum clarity, making the listening experience rich and immersive. The system supports multiple source components, including CD players, streaming devices, and more, ensuring compatibility with a variety of audio formats.

Another key characteristic of the MRC88M is its user-friendly interface. Users can control the system using an intuitive remote, mobile app, or wall-mounted keypads, allowing for easy operation regardless of the user’s technical expertise. The customizable interfaces enable users to tailor the controls to meet individual preferences, enhancing the ease of use throughout the home.

Integration with smart home systems is another significant advantage of the MRC88M. It supports control via popular platforms, which allows homeowners to incorporate their audio system into broader home automation settings. This connectivity enables voice control and advanced scheduling features, making it not only a multi-room audio solution but also a vital part of a smart home ecosystem.

The MRC88M also features robust build quality and supports a wide range of speaker configurations, ensuring that it can accommodate both in-wall and traditional speakers. This versatility makes it suitable for any living space, whether in a new build or retrofitted into an existing residence.

In conclusion, the Xantech MRC88M is a top-tier multi-room audio solution that combines high-quality sound, flexible zone control, and seamless integration into smart home systems. Its advanced technology and user-friendly design make it a perfect choice for those looking to elevate their audio experience throughout their home.
Top Page Image Contents