Xantech MRAUDIO8X8M, MRC88M Control Out, CO1 and CO2 Zones 7, Zone IR BASIC/ADVANCED/EXPANDED

Page 29

Model MRC88m / MRAUDIO8x8m

Page: 29

Mini jack to the appropriate zone Status connector on the rear of the MRC88m Controller/Amplifier and the other end to the device to control. Tip=Control Voltage; Sleeve=GND

Control Out

(BASIC/ADVANCED)

A single Common Control Output is provided on the rear of the MRC88m Controller/Amplifier –Figure 3- (20). When the Common Control Output is High (+12 volts, 50 mA), this indicates that ‘at least’ one zone is powered ON. When the Common Control Output is Low (0 volts), this indicates that ‘all’ zones are OFF. Using a 3.5mm mono mini phone connector, this control can be used to close relays (Xantech CC12) or turn on an AC outlet (Xantech AC1, AC2) for activity common to the system. Connect one end of the 3.5mm Mono Mini jack and the other end to the device to control. Tip=Control Voltage; Sleeve=GND

(EXPANDED)

When at least one zone on either the PRIMARY or SECONDARY controller is turned ON, the Control Out on the PRIMARY Controller is High (+12VDC). The Control Out on the SECONDARY Controller is inactive in EXPANDED mode.

PREAMP OUT

(BASIC/ADVANCED/EXPANDED)

Each zone has a Preamp Out to send ‘zone selected’ audio to another amplifier such as the Xantech PA435x or PA4100x. This may be desired for feeding a sub-zone on a separate amplifier, zones that require more than 35W, or for sending audio to another amplifier with Dolby™ surround decoding for ‘theater quality’ audio in the zone.

Using good quality RCA-type patch cables, connect the Preamp Out, Left(L) and Right(R) connectors – Figure 3-(25), to the desired external amplifiers Audio Left and Right Input connectors.

CO1 AND CO2 (ZONES 7 & 8)

(BASIC/ADVANCED/EXPANDED)

Zones 7 and 8 have a Remote Mute/Standby output for interfacing and controlling a Xantech PA435X (included) or PA4100X amplifier. The control is provided via a Stereo Mini Jack with the TIP controlling STANDBY logic (Standby Power On = +12 volts, Standby Power Off = 0 volts) and the RING controlling MUTE logic (Mute = +12 volts, Un-Mute = 0 volts).

Using a 3.5mm Stereo Mini Jack to 3.5mm Stereo Mini Jack cable, plug one end into the CO1 (or CO2) output jack on the rear of the MRC88m Controller/Amplifier – Figure 3-(21)and the other end into the corresponding jack labeled CO1 (or CO2) on the PA435X or PA4100X amplifier.

NOTE: Be sure to set the Control In (CI) switch to ON located on the rear of the PA435X or PA4100X amplifier.

ZONE IR (BASIC/ADVANCED/EXPANDED)

Using Xantech Emitters (282M, 283M,284M, or 286M), plug the 3.5mm Mono Mini jack into the appropriate zones Zone IR connector – Figure 3-(28). Affix the mouse emitter side to the desired zone related component you wish to control. If more than one device needs to be controlled, use a mono mini to stripped-ends wire (PN#6015900) wired to a Xantech 791-44 Amplified Connecting block. Any IR generated in the zone (either from MRC-88 Keypad, IR received at the Keypad, or routed from another zone (ADVANCED only)) will be passed to this emitter port.

AC POWER CONNECTIONS

(BASIC/ADVANCED/EXPANDED)

Use the supplied power cable and plug into a power source capable of delivering the rated amps shown in the specification section of this manual.

© 2009 Xantech Corporation

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Model MRC88m Model MRAUDIO8x8m Not Expose this Appliance to Rain or Moisture Safety Instructions Read Before Operating EquipmentTable of Contents Programming the Controller ADVANCED/EXPANDED Programming Tweaking the System Model MRC88m / MRAUDIO8x8m Xantech Corporation MRC88m system includes the following components General InformationModel MRC88m / MRAUDIO8x8m System Overview System Block DiagramCONTROLLER/AMPLIFIER Features Keypad Features Front Panel MRC88M Front Panel Features and ConnectionsSystem Status Power-Up Mode Zone Status Active-Operational Mode Source Component Input Connections MRC88M Rear Panel Features and ConnectionsSource Loop-Thru Connections MRC88m Keypad MRC88M Keypad Front FeaturesModel MRC88m / MRAUDIO8x8m MRC88M Keypad Rear Features and Connections Model MRC88m Keypad Rear Panel Features and FunctionsOperation OUT-OF-THE-BOX PRE Test BASIC/ADVANCED/EXPANDED InstallationMRC88 Expanded Mounting and Installing the MRC88m KeypadMRC88m Keypad mounting template MRC88M Keypad Removal Optional Keypad Back-Box for pre-install applicationsVideo Connections MRC88m Only Audio ConnectionsBASIC/ADVANCED Advanced CSM1 Threshold AdjustmentsBASIC/ADVANCED/EXPANDED Zone Related Wiring ConnectionsStatus BASIC/ADVANCED/EXPANDED Composite VideoModulated Video Zone IR BASIC/ADVANCED/EXPANDED Control OutCO1 and CO2 Zones 7 OFF Connections AT the Zone Location BASIC/ADVANCED/EXPANDEDZone IR Zone Expansion Connecting TWO MRC88M Controllers ExpandedMRC88m Keypad CAT5 Cable Lengths MRC88m Connecting Block located on rear of KeypadVideo Connections SETTING-UP the MRC88m System Pre-Programming the MRC88m BASIC/ADVANCED/EXPANDED Computer Requirements Minimum Basic Mode Advanced Mode Expanded ModePlanning the System Software Installation Connecting the MRC88M CONTROLLER/AMPLIFIER to the PCIncluded Hardware & Software Items Starting MRC88M Dragon DROP-IR SoftwareStarting a Project BUILT-IN IR Code Library BASIC/ADVANCED/EXPANDED Learning IR Commands Creating Palette FilesLearning IR Commands BASIC/ADVANCED/EXPANDED Built-In Mfg’s IR Command LibraryRecording Toggle Command Functions Creating a Palette File BASIC/ADVANCED/EXPANDED To Rename an Existing FunctionTo Add a New Function Importing CCF Files Getting Source Commands from the InternetEditing BRAND, COMPONENT, and Function Lists Importing Discrete IR Hex Codes ADVANCED/EXPANDED Entering RS232 Command StringsRS232 Palette Editor Window Using PC TestUsing MRC88m Test Creating an RS232 Palette File Creating AN RS232 Palette File ADVANCED/EXPANDEDProgramming The Controller Downloading Source Icons to the Keypad Creating NEW IconsSelecting Icons from the Icon Generator Selecting RS232 Command Palettes ADVANCED/EXPANDED Placing Commands Onto the Virtual KeypadSelecting Internal Amplifier Commands ADVANCED/EXPANDED Placing Commands on the Virtual Keypad BasicProgramming Sequences Macros Editing Buttons on the Virtual Keypad Button Edit Pop-Up MenuEditing Commands in the Macro Command List Window Zone 1 thru Editing CommandsProgramming Power Management Programming Power Management and Sense Trigger CodesBasic Power Management Programming Sense Triggers Programming Sense Trigger Codes ADVANCED/EXPANDEDTesting Commands Under Power Management and Sense Triggers Default settings set in Basic Mode are as follows Zone Options ConfigurationName of Zone ADVANCED/EXPANDED RC68 Code GroupIR Loop Back Settings ADVANCED/EXPANDED PRE AMP Volume Adjust Settings ADVANCED/EXPANDEDTransferring the Project Configuring Commands for IR in ZoneZone Audio Input Controller Options ProgrammingIR Routing Mode of OperationBACK-LIGHT Control Expanded OptionsMonitor Lockout Mode Factory default Disabled RS232 SettingsMonitor Lockout Mode Zone Linking Programming Dynamic Zone Link Mode Factory default Disabled Link ALL Dynamic RS232 Input TranslatorLink ALL Static Clear ALLIRS232 Input Translator Programming IR Commands and SequencesRC68+ IR Code Triggered Sequencer RC68 IR Command Macro WindowInternal Amplifier Command Window Programming Internal Amplifier CommandsUsing Internal Amplifier Commands Internal Amplifier Commands Zone Expansion Connecting Multiple MRC88M ControllersPhysical Connections in Expanded Mode Programming in Expanded ModeEnabling Expanded Mode RS232 Control While in Expanded Mode Sources 1 through Completing the Programming Process Saving and BACKING-UP Files Warm Firmware Upgrade Firmware Upgrade OptionsCold Firmware Upgrade Downloading Firmware Files from the WEBTweaking the System Trimming Source Audio Input Levels Making Fine AdjustmentsKeypad Adjustments Zone AdjustmentsSetting the Volume Powering the Zone on and OFFAccessing Tier 2 Commands Source Slection and ControlAudio Adjustments BASIC/ADVANCED/EXPANDED Zone SettingsSystem Status BASIC/ADVANCED Dynamic Monitor Lockout Parental Control ADVANCED/EXPANDEDExpanded RS232 Control ?5SS3+ 7PR1+?5SS+ AO+ Commands?z#PR+ QueriesVolume Level 39 Steps Keypad Button ID MRC88m Setting Level in dB +14 +12 +10 Balance Level MRC88m Left Speaker Right Speaker Attenuation SettingProblem Probable Cause and Solution TroubleshootingModel MRC88m / MRAUDIO8x8mPage 96Model MRC88m / MRAUDIO8x8m Problem Probable Cause and Solution RS232 and Expansion PIN OUT Information Certifications SpecificationsVideo IR SensorModel MRC88m / MRAUDIO8x8m Model MRC88m / MRAUDIO8x8m Xantech Corporation Xantech Corporation
Related manuals
Manual 7 pages 32.14 Kb Manual 10 pages 43.55 Kb Manual 12 pages 31.84 Kb

MRAUDIO8X8M, MRC88M specifications

The Xantech MRC88M is a sophisticated multi-room audio system that seamlessly integrates into modern home environments, offering unparalleled control and quality of sound distribution. Designed for audiophiles and casual listeners alike, this powerful system enables users to enjoy their favorite music, podcasts, and audio from multiple sources throughout their home.

One of the standout features of the MRC88M is its 8-zone capability, allowing users to create and control up to eight independent audio zones. Each zone can customize its volume, source selection, and audio settings, providing a highly personalized audio experience. This flexibility means that different rooms can enjoy varied audio at the same time, making it ideal for entertaining guests or relaxing in private spaces.

The MRC88M employs advanced technologies to ensure high-quality sound reproduction. It uses a reliable audio matrix router that allows for the precise routing of audio signals between connected sources and zones. This ensures minimal interference and maximum clarity, making the listening experience rich and immersive. The system supports multiple source components, including CD players, streaming devices, and more, ensuring compatibility with a variety of audio formats.

Another key characteristic of the MRC88M is its user-friendly interface. Users can control the system using an intuitive remote, mobile app, or wall-mounted keypads, allowing for easy operation regardless of the user’s technical expertise. The customizable interfaces enable users to tailor the controls to meet individual preferences, enhancing the ease of use throughout the home.

Integration with smart home systems is another significant advantage of the MRC88M. It supports control via popular platforms, which allows homeowners to incorporate their audio system into broader home automation settings. This connectivity enables voice control and advanced scheduling features, making it not only a multi-room audio solution but also a vital part of a smart home ecosystem.

The MRC88M also features robust build quality and supports a wide range of speaker configurations, ensuring that it can accommodate both in-wall and traditional speakers. This versatility makes it suitable for any living space, whether in a new build or retrofitted into an existing residence.

In conclusion, the Xantech MRC88M is a top-tier multi-room audio solution that combines high-quality sound, flexible zone control, and seamless integration into smart home systems. Its advanced technology and user-friendly design make it a perfect choice for those looking to elevate their audio experience throughout their home.
Top Page Image Contents