Euro-Pro EP96W owner manual Speed Control Dial, Operating the Food Processor, Setting up

Fig. 2

GETTING TO KNOW YOUR QUAD BLADE FOOD

OPERATING INSTRUCTIONS

PROCESSING CENTER

1.	Processor Body	17.	Juice Extractor Filter
2.	Safety Cover	18.	Whipping Attachment
3.	Safety Cover/Blender Location	19.	Citrus Juicer Filter
4.	On/Off Speed Control Dial	20.	Juice Reamer
5.	Turbo/Pulse Button	21.	Main Chopping Blade
6.	Drive Shaft	22.	Double Chopping Blade
7.	Storage Compartment	23.	Chopping Blade Protective Cover
8.	Blender Jar	24.	Blade Holder
9.	Blender Lid	25.	French Fry Disk Assembly
10.	Measuring Cap	26.	Dough Blade
11.	Processor Bowl	27.	Thick Slicing Blade
12.	Spindle	28.	Thin Slicing Blade
13.	Processor Lid	29.	Fine Chopping Blade
14.	Food Pusher	30.	Coarse Chopping Blade
15.	Juice Extractor Lid	31.	Spatula
16.	Juice Extractor Pusher

Technical Specifications

Voltage:	120V., 60Hz.
Power:	800 Watts
Food Processor Capacity:	6	Cups (1.5 Liters)
Blender Capacity:	7	Cups (1.75 Liters)

Speed Control Dial

The food processor and blender speed control dial has speeds settings as follows: (Fig. 1)

Off/1-9 + Max

Pulse/Turbo

The speed can be
adjusted while the
food processor is
in use.	Fig. 1

Use of the Pulse/Turbo button allows greater control over the texture of the food being processed. Use "Pulse" when the unit is in the "Off" position. Use "Turbo" when the unit is in the "On" position and you need a burst of power. Please note that the "Pulse" and "Turbo" is only intended to be used for short "bursts" of processing.

Operating the Food Processor

Setting up:

1.CAUTION: Make sure that the unit is unplugged from the power source and the the Speed control dial is in the "Off" position before inserting or removing any attachments and before cleaning.

2.Fit the safety cover into the food processor body and turn counterclockwise firmly until it “clicks” into place (the arrows will now be lined up). IMPORTANT THE FOOD

PROCESSOR WILL NOT OPERATE WITHOUT THE SAFETY COVER IN PLACE.

3.Place the food processor bowl onto the processor body.

There is no need to turn the bowl. (Fig. 2)

4.When fitted correctly, the handle will be to the right of the

assembly, and the ridge on the base

of the bowl will fit into the slot at the back of the processor body.

(Fig. 3 & Fig. 4)

Fig. 3 Fig. 4

5.Fit the spindle onto the motor shaft and the appropriate attachments onto the spindle. (Fig. 5)

WARNING

TO REDUCE THE RISK OF INJURY, NEVER PLACE THE CUTTING BLADE ON THE BASE WITHOUT FIRST PUTTING THE BOWL PROPERLY IN PLACE.

Fig. 5

6. Holding the	Fig. 6
processor lid
by the feed tube,
fit the lid by
rotating
counterclockwise.
(Fig. 6)

7.Ensure that the lid tab has “clicked” into place and the arrows are lined up. (Fig. 8)

8.Plug the processor Fig. 7 and switch on.

If the processor does not come on, check that the machine cover and processor lid are

both correctly fitted. Fig8 (Fig. 8)

For safety, always
use the food
pusher when
putting food into
the feeder tube.
Never feed by
hand. (Fig. 9)	Fig9

WARNING: Always remove the blender and fit the safety cover into the processor body when using the processor.

3 4