Frymaster *8196329* manual General Use, Start-Up Procedures

Page 27

YSCFHC18G HIGH EFFICIENCY COOL ZONE SERIES GAS FRYERS

CHAPTER 4: DAILY OPERATION

4.1General Use

1.At opening, always check that the power switch and the computer are OFF.

2.For consistent quality product, convenience, and long-term savings, use a high-quality liquid shortening.

3.If using solid shortening, never melt a block of shortening by placing an entire block in the fryer vessel. Cut it into small pieces and pack it around fryer components.

4.Although 350°F (177°C) is the recommended temperature for most cooking operations, set the fryer at the lowest possible temperature which produces a high quality end product while ensuring maximum life for your oil.

4.2Start-Up Procedures

1.If the fryer is empty, pour enough oil into the frypot to fill it to the bottom OIL LEVEL line scribed on the rear wall. If solid shortening is used, melt the shortening following procedures in Section 3.10, Final Preparation.

A.Pilot lighting procedure – Electronic Ignition

a.Turn gas "ON."

b.Turn electric power "ON" with the appropriate rocker switch or controller/computer.

c.The ignition module will energize the pilot gas supply and the ignitor. The ignitor spark will ignite the pilot gas. The presence of the pilot flame is then proven by a flame sensor, which sends a signal to the main gas supply, opening the valve. The operating thermostat or computer/controller controls the fryer after ignition.

WARNING

In the event of prolonged power failure, the ignition module will shut down and lock out the system. Turn the unit power "OFF" and then back "ON" after power has been re-established.

d.If the pilot flame fails, the ignition module will shut down and lock out the system. To restart, turn the electric power "OFF,” wait approximately 5 minutes for the system to recycle itself, and then turn the power "ON" again. Repeat Steps a-c.

4-1

Page 26 Page 28
Image 27
Page 26 Page 28
Contents YSCFHC18G High Efficiency Cool Zone Series Gas Fryers Page Page YSCFHC18G Cool Zone Gas Fryers Ordering Parts After PurchaseService Information Safety InformationComputer Information Safety Information Service Personnel Receiving and Unpacking Equipment GeneralIf your equipment arrives damaged Pre-Installation Principles of OperationRating Plate ANSI/NFPA #70 Australian installations must meetAir Supply and Ventilation Equipment Installed at High AltitudesRestraining the Fryer Page Installing the Fryer Leg and Caster InstallationGeneral Leveling the Fryer InstallationInstalling Optional Swivel Casters Legs OnlyRigid Casters Only Gas Connections Rigid Connections Manual Shut-off ValveRegulating Gas Pressure Flexible Couplings, Connectors and Casters Adjustments/Adaptation To Different Gases GAS Supply for Which IT is not Configured Gas Conversion ProceduresSafety Switches Electrical ConnectionsFryer with KFC-1 Computer Microswitch is located on the red handle at the drain valve Return system Final Preparation Initial Cleaning Before StartupDrop Start-Up Procedures Pilot lighting procedure Electronic IgnitionGeneral Use ON/OFF Buttons See for detailed filtration procedures FilteringClosing Filter Powder Filter Paper Filter PreparationFilter Preparation Page Filter Operations Remove large debris floating in the oil Removing support grid from frypot prior to draining Filter Operations Filter Operations Page Weekly DailyBuilt-in Filtration Periodic/AnnualStainless Steel Periodic/ AnnualIntroduction Pressed Fryer TroubleshootingFryer Troubleshooting Burner Tube Remains after closing drain Main burner malfunctions Pump wont Start Filtration System TroubleshootingWiring Diagrams Fast-Equipped Control and Filter Circuit KFC-1 Equipped Control and Filter Circuit Service Hotline

*8196329* specifications

Frymaster 8196329 is a state-of-the-art commercial fryer that is engineered to meet the demands of busy kitchens while ensuring the highest quality of frying results. Known for its reliability and efficiency, this fryer's innovative features make it a preferred choice among chefs and restaurant operators.

One of the standout features of the Frymaster 8196329 is its advanced oil filtration system. This system extends the life of the cooking oil, resulting in lower operational costs and improved food quality. The automatic filtration process removes impurities from the oil, enhancing flavor and ensuring a consistent frying experience. This feature is especially beneficial in high-volume environments, as it allows for minimal downtime and easy maintenance.

The Frymaster 8196329 is equipped with a variety of cooking controls that enhance usability. Its digital control panel offers precise temperature settings, promoting better control over the frying process. The intelligent temperature adjustment technology ensures that the oil maintains the optimal frying temperature, which is crucial for achieving perfectly crispy results. This ensures food is cooked uniformly while saving energy.

In addition to its cooking controls, the Frymaster 8196329 boasts a large capacity, accommodating various food types, from French fries to chicken wings. With multiple fry baskets, operators can cook different items simultaneously, thus increasing kitchen efficiency. The fryer's design promotes even heat distribution, which results in a consistent texture across all fried foods.

Another notable characteristic of the Frymaster 8196329 is its robust construction. Designed with heavy-duty materials, this fryer is built to withstand the rigorous demands of any commercial kitchen. The easy-to-clean surfaces and ergonomic design make maintenance less cumbersome, allowing kitchens to maintain a high standard of cleanliness.

The energy efficiency of the Frymaster 8196329 cannot be understated. With features designed to minimize energy consumption while maximizing output, it promotes a more sustainable approach to frying. This not only benefits the environment but also contributes to cost savings in the long run.

In summary, the Frymaster 8196329 embodies the perfect blend of technology, efficiency, and durability. With its advanced oil filtration system, intuitive controls, ample cooking capacity, and energy-efficient operation, it remains a top choice for those seeking high-quality performance in commercial frying applications.
Top Page Image Contents